Fox and McDonald's Introduction to Fluid Mechanics
9th Edition
ISBN: 9781118912652
Author: Philip J. Pritchard, John W. Mitchell
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 11, Problem 37P
This large uniform open channel flow is to be modeled without geometric distortion in the hydraulic laboratory at a scale of 1:9. What flow rate, bottom slope, and Manning n will be required in the model?
P11.37
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Water at 65°F flows at a depth of 1.4 ft with an average velocity of 20 ft/s in a wide rectangular channel. Determine (a) the Froude number, (b) the critical depth, and (c) whether the flow is subcritical or supercritical. What would your response be if the flow depth were 0.2 ft
Water fl ows down a rectangular channel that is 4 ft wideand 2 ft deep. The fl ow rate is 20,000 gal/min. Estimate theFroude number of the fl ow.
In flowing from section (1) to section (2) along a rectangular open channel, the water depth decreases by a factor of three and the Froude number changes from a subcritical value of 0.7 to a supercritical value of 3.4. Determine the channel width at (2) if it is 8 ft. wide at section (1). Assume stead-state flow.
Chapter 11 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Ch. 11 - Verify the equation given in Table 11.1 for the...Ch. 11 - A pebble is dropped into a stream of water that...Ch. 11 - Solution of the complete differential equations...Ch. 11 - A water flow rate of 250 cfs flows at a depth of 5...Ch. 11 - Determine and plot the relation between water...Ch. 11 - Capillary waves (ripples) are small amplitude and...Ch. 11 - The Froude number characterizes flow with a free...Ch. 11 - Consider waves on the surface of a tank of water...Ch. 11 - A submerged body traveling horizontally beneath a...Ch. 11 - Water flows in a rectangular channel at a depth of...
Ch. 11 - A partially open sluice gate in a 5-m-wide...Ch. 11 - Find the critical depth for flow at 3 m3/s in a...Ch. 11 - Flow occurs in a rectangular channel of 6 m width...Ch. 11 - What is the maximum flow rate that may occur in a...Ch. 11 - A rectangular channel carries a discharge of 10...Ch. 11 - Flow in the channel of Problem 11.15 has a...Ch. 11 - Consider the Venturi flume shown. The bed is...Ch. 11 - Eleven cubic meters per second of water are...Ch. 11 - A rectangular channel 10 ft wide carries 100 cfs...Ch. 11 - At what depths can 800 cfs flow in a trapezoidal...Ch. 11 - At a section of a 10-ft-wide rectangular channel,...Ch. 11 - Water, at 3 ft/s and 2 ft depth, approaches a...Ch. 11 - A horizontal rectangular channel 3 ft wide...Ch. 11 - A hydraulic jump occurs in a rectangular channel...Ch. 11 - A hydraulic jump occurs in a wide horizontal...Ch. 11 - A hydraulic jump occurs in a rectangular channel....Ch. 11 - The depths of water upstream and downstream from a...Ch. 11 - Calculate y2, h, and y3 for this two-dimensional...Ch. 11 - The hydraulic jump may be used as a crude flow...Ch. 11 - A hydraulic jump occurs on a horizontal apron...Ch. 11 - A hydraulic jump occurs in a rectangular channel....Ch. 11 - A positive surge wave, or moving hydraulic jump,...Ch. 11 - A 2-m-wide rectangular channel with a bed slope of...Ch. 11 - Determine the uniform flow depth in a rectangular...Ch. 11 - Determine the uniform flow depth in a trapezoidal...Ch. 11 - Water flows uniformly at a depth of 1.2 m in a...Ch. 11 - This large uniform open channel flow is to be...Ch. 11 - A rectangular flume built of timber is 3 ft wide....Ch. 11 - A channel with square cross section is to carry 20...Ch. 11 - A triangular channel with side angles of 45 is to...Ch. 11 - A flume of timber has as its cross section an...Ch. 11 - At what depth will 4.25 m3/s flow uniformly in a...Ch. 11 - A semicircular trough of corrugated steel, with...Ch. 11 - A rectangular flume built of concrete with 1 ft...Ch. 11 - Water flows in a trapezoidal channel at a flow...Ch. 11 - What slope is necessary to carry 11 m3/s uniformly...Ch. 11 - Find the normal depth for the channel of Problem...Ch. 11 - For a trapezoidal shaped channel with n = 0.014...Ch. 11 - Compute the critical depth for the channel in...Ch. 11 - A trapezoidal canal lined with brick has side...Ch. 11 - An optimum rectangular storm sewer channel made of...Ch. 11 - For a sharp-crested suppressed weir of length B =...Ch. 11 - A rectangular sharp-crested weir with end...Ch. 11 - What is the depth of water behind a rectangular...Ch. 11 - A broad-crested weir 0.9 m high has a flat crest...Ch. 11 - The head on a 90 V-notch weir is 1.5 ft. Determine...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
The force in each member of truss and the state of members are in Tension or Compression.
Engineering Mechanics: Statics & Dynamics (14th Edition)
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Determine the maximum compression of the spring mounted on car A. Neglect rolling resistance.
Engineering Mechanics: Dynamics (14th Edition)
For the compound manometer shown in Fig.3.31, calculate the pressure at point A
Applied Fluid Mechanics (7th Edition)
Determine the normal stress in each member of the truss structure. All joints are ball joint, and the material ...
Introduction To Finite Element Analysis And Design
Steady state conduction rate to the warm compressor to the net power produces theoretically by thermodynamic ba...
Introduction to Heat Transfer
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A trapezoidal channel having a bottom slope of 0.001 is carrying a flow of 30 m/s. The bottom width is 10.0 m and the side slopes are 2H to 1V. A control structure is built at the downstream end which raises the water depth at the downstream end to 5.0 m. Compute the water surface profile till 1.20 m. Manning n is 0.013 and a = 1. Select an appropriate Month for your calculations. Please read the question carefully and provide the correct solution with simple steps fast. Please answer quickly.arrow_forwardDraw and label a hydraulic jump (in a channel of constant width). (a) Indicate regions of supercritical and subcritical flow. (b) What happens to Bernoulli’s constant through the jump? (c) Write down the relationship between the ratio of upstream and downstream water depths, and the upstream Froude number. (d) Derive a relationship between the ratio of upstream and downstream water depths, and the downstream Froude number. (e) A surge is moving at 5 m/s into an estuary of depth 1 m where the water is moving out to sea at 1 m/s. Find the water depth behind the surge.arrow_forwardWater flows uniformly in a rectangular channel with finished-concrete surfaces. The channel width is 3 m, the flow depth is 1.2 m, and the bottom slope is 0.002. Determine if the channel should be classified as mild, critical, or steep for this flow.arrow_forward
- Water flows at a steady and uniform depth of 2 m in an open channel of rectangular crosssection having a base width equal to 5 m and laid at a slope of 1 in 1000. It is desired to obtain critical flow in the channel by providing a hump in the bed. Calculate the height of the hump and sketch the flow profile. Consider the value of Manning’s roughness coefficient n =0.02 for the channel surface.arrow_forwardA rectangular channel is 3m wide and has a depth of flow of 1.5m. The channel roughness can be assumed to be 0.015 and the bed slope is 0.001. Calculate The height by which the bed should be raised to just produce critical depth The width by which the bed should be narrowed to just produce critical deptharrow_forwardWater flows in a 9-m-wide rectangular open channel at a rate of 55 m3/s. If the flow depth is 2.4 m, the Froude number is (a) 0.682 (b) 0.787 (c) 0.525 (d) 1.00 (e) 2.65arrow_forward
- Water fl owing in a wide channel 25 cm deep suddenlyjumps to a depth of 1 m. Estimate (a) the downstreamFroude number; (b) the fl ow rate per unit width; (c) thecritical depth; and (d ) the percentage of dissipation.arrow_forwardWater flows steadily and smoothly through an open-channel flow of varying width, as shown in Figure P10.21. The Froude number at the upstream station is subcritical and equal to F1, and the width and depth at this station are w1 and h1, respectively. At the point of minimum channel width (the “throat”), the Froude number F2 = 1, and the width and depth are w2 and h2. Downstream of the throat the channel expands to a constant width, and at this point the Froude number is F3 and the width and depth of the flow are w3 and h3. Note that h2/h1 = 3/4, and w3 = w1. State all your assumptions. (a) Find F1 (this is a number). (b) Find w2/w1 (this is a number). (c) Show that h1/h3 is approximately equal to 2.37.arrow_forwardWater is flowing uniformly in a rectangular open channel with unfinished-concrete surfaces. The channel width is 6 m, the flow depth is 2 m, and the bottom slope is 0.004. Determine if the channel should be classified as mild, critical, or steep for this flowarrow_forward
- Water in a two-dimensional channel flows smoothly over a submerged obstacle of height H as shown in Figure P10.12. The water depth at the peak of the obstacle is Y2, where Y2 = Y1/3. (a) Find the value of the Froude number of the incoming flow, F1, given that the Froude number is unity at the point where the depth is Y2. (b) Find the nondimensional height of the obstacle, H/Y1.arrow_forwardDesign a box culvert to carry a design discharge of 600 cfs. The culvert invert elevation is 2100 feet, and the allowable headwater elevation is 2114 feet. The paved roadway is 500 feet long and overtops at an elevation of 2115 feet. The culvert length is 200 feet with a slope of 1%. The following tailwater elevations apply up to the maximum discharge of 1000 cfs: Discharge (cfs) 200.00 400.00 600.00 800.00 1000.0Tailwater, ft 2101.4 2102.6 2103.1 2103.8 2104.1 Prepare a performance curve of the culvert design by hand and compare with the results of HY8. Also, use HY8 to prepare a performance curve if the slope is 0.5%.arrow_forwardFor an open channel having a trapezoidal section, the most efficient is the one whose shape is that of semi-regular hexagon. If such channel carries 4 m3/s of water flowing at 50 cm/s, the base width in meters isarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Everything About TRANSVERSE SHEAR in 10 Minutes!! - Mechanics of Materials; Author: Less Boring Lectures;https://www.youtube.com/watch?v=4x0E9yvzfCM;License: Standard Youtube License