EBK FLUID MECHANICS: FUNDAMENTALS AND A
4th Edition
ISBN: 8220103676205
Author: CENGEL
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 12, Problem 10P
Products of combustion enter a gas turbine with a stagnation pressure of 0.90 MPa and a stagnation temperature of 840°C, and they expand to a stagnation pressure of 100 kPa. Taking
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
2- Products of combustion enter a gas turbine with a stagnation pressure of 0.75
MPa and a stagnation temperature of 690 °C, and they expand to a stagnation
pressure of 100 kPa. Taking cp = 1.157 kJ/kg.K, k = 1.33 and R = 0.287 kJ/kg-K for the
products of combustion, and assuming the expansion process to be isentropic,
determine the power output of the turbine per unit mass flow.
Nitrogen is expanded isentropically in a nozzle from a pressure of 2000 kPa, at a
temperature of 1000 K, to a pressure of 101 kPa. If the velocity of the nitrogen entering the
nozzle is negligible, determine the exit nozzle area required for a nitrogen flow of 0.5 kg/s.
Assume the nitrogen to behave as a perfect gas with constant specific heats, mean molecular
mass of 28.0, and y 1.4.
A 5-feet diameter Chimney is designed to handle a flue gas produced in a steam power plant at a rate of 17 lb/s. The barometric pressure is 29.92-inch Hg. Outside air enters the combustion chamber at 90 F. The average temperature of the flue gas inside the Chimney is 572 F and its molecular weight is 30. Cv = 0.35, Rair = 53.342 ft-lb/lb-R. Calculate:
5. The total draft, feet of air.
6. The height of the Chimney, feet
Chapter 12 Solutions
EBK FLUID MECHANICS: FUNDAMENTALS AND A
Ch. 12 - What is dynamic temperature?Ch. 12 - Calculate the stagnation temperature and pressure...Ch. 12 - Prob. 6PCh. 12 - Prob. 7PCh. 12 - Prob. 8EPCh. 12 - Prob. 9PCh. 12 - Products of combustion enter a gas turbine with a...Ch. 12 - Is it possible to accelerate a gas to a supersonic...Ch. 12 - Prob. 72EPCh. 12 - Prob. 73P
Ch. 12 - Prob. 74PCh. 12 - Prob. 75PCh. 12 - For an ideal gas flowing through a normal shock,...Ch. 12 - Prob. 77CPCh. 12 - On a T-s diagram of Raleigh flow, what do the...Ch. 12 - What is the effect of heat gain and heat toss on...Ch. 12 - Prob. 80CPCh. 12 - Prob. 81CPCh. 12 - Prob. 82CPCh. 12 - Argon gas enters a constant cross-sectional area...Ch. 12 - Prob. 84EPCh. 12 - Prob. 85PCh. 12 - Prob. 86PCh. 12 - Prob. 87EPCh. 12 - Prob. 88PCh. 12 - Prob. 89PCh. 12 - Prob. 90PCh. 12 - Prob. 91PCh. 12 - Prob. 93CPCh. 12 - Prob. 94CPCh. 12 - Prob. 95CPCh. 12 - Prob. 96CPCh. 12 - Prob. 97CPCh. 12 - Prob. 98CPCh. 12 - Prob. 99CPCh. 12 - Prob. 100CPCh. 12 - Prob. 101PCh. 12 - Air enters a 5-cm-diameter, 4-m-long adiabatic...Ch. 12 - Helium gas with k=1.667 enters a 6-in-diameter...Ch. 12 - Air enters a 12-cm-diameter adiabatic duct at...Ch. 12 - Prob. 105PCh. 12 - Air flows through a 6-in-diameter, 50-ft-long...Ch. 12 - Air in a room at T0=300k and P0=100kPa is drawn...Ch. 12 - Prob. 110PCh. 12 - Prob. 112PCh. 12 - Prob. 113PCh. 12 - Prob. 114PCh. 12 - Prob. 115PCh. 12 - Prob. 116EPCh. 12 - A subsonic airplane is flying at a 5000-m altitude...Ch. 12 - Prob. 118PCh. 12 - Prob. 119PCh. 12 - Prob. 120PCh. 12 - Prob. 121PCh. 12 - Prob. 122PCh. 12 - Prob. 123PCh. 12 - An aircraft flies with a Mach number Ma1=0.9 at an...Ch. 12 - Prob. 125PCh. 12 - Helium expands in a nozzle from 220 psia, 740 R,...Ch. 12 - Prob. 127PCh. 12 - Prob. 128PCh. 12 - Prob. 129PCh. 12 - Prob. 130PCh. 12 - Prob. 131PCh. 12 - Prob. 132PCh. 12 - Prob. 133PCh. 12 - Prob. 134PCh. 12 - Prob. 135PCh. 12 - Prob. 136PCh. 12 - Prob. 137PCh. 12 - Prob. 138PCh. 12 - Air is cooled as it flows through a 30-cm-diameter...Ch. 12 - Prob. 140PCh. 12 - Prob. 141PCh. 12 - Prob. 142PCh. 12 - Prob. 145PCh. 12 - Prob. 148PCh. 12 - Prob. 149PCh. 12 - Prob. 150PCh. 12 - Prob. 151PCh. 12 - Prob. 153PCh. 12 - Prob. 154PCh. 12 - Prob. 155PCh. 12 - Prob. 156PCh. 12 - Prob. 157PCh. 12 - Prob. 158PCh. 12 - Prob. 159PCh. 12 - Prob. 160PCh. 12 - Prob. 161PCh. 12 - Prob. 162PCh. 12 - Assuming you have a thermometer and a device to...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- An ideal gas enters a turbine with a velocity of 40 m/s through an inlet pipe with a diameter of 160 mm. The ideal gas enters the turbine at a temperature of 660°C and a pressure of 800 kPa. The ideal gas leaves the turbine with a velocity of 150 m/s through an outlet pipe with a diameter of 100 mm. The power output from the turbine is 350 kW. The heat lost from the turbine to the surrounding amounts to 6% of the power output from the turbine. Changes in kinetic energy and potential energy can be neglected. For the ideal gas, use R = 0.287 kJ/kg.K and c, = 1.11 kJ/kg.K| i) Sketch the system/control volume for the above problem Show the boundary/control surface and energy interactions clearly in the sketch. 11) Determine the mass flow rate of the ideal gas, kg/s. i11) Determine the temperature of the ideal gas leaving the turbine, °C. iv) Determine the pressure of the ideal gas leaving the turbine, kPa. v) Suggest one way to increase the power output from the turbine.arrow_forwardAir flows steadily through a varying cross-sectional area duct such as a nozzle at a mass flow rate of 10 lb/s. The air enters the duct at a pressure of 200 lb/in2 and 445°F with a low velocity, and it expands in the nozzle to an exit pressure of 30 lb/in2. The duct is designed so that the flow can be approximated as isentropic. Determine the density, velocity, flow area, and Mach number at each location along the duct that corresponds to an overall pressure drop of 30 lb/in2.arrow_forwardQuestion B2 A civilian aircraft is flying at a Mach number of 0.8 at an altitude where the ambient pressure and temperature are 26.5 kPa and 223 K, respectively. The aircraft is equipped with two simple turbojet engines. The stagnation temperature at the entrance to their nozzles is 1200K and remains unchanged. You may assume the nozzles are operating under ideal conditions and the properties of hot gases leaving the nozzles are the same as air. 1- Under certain operating conditions each engine produces a gross thrust of 50×10³ N with an exit velocity of 600 m/s. For each nozzle determine its mass flow rate, exit area and the corresponding stagnation pressure at its entrance. 2- For a fuel to air ratio of 0.02, determine the net thrust of each engine corresponding to the above (part 1) operating condition. 3- What should be the minimum supply pressure to the nozzles if they were operating at choked condition? Then determine the gross thrust of each nozzle. 4- Show that for a choked…arrow_forward
- Steam at a pressure of 0.58 MPa has an internal energy of 2725.2 kJ/kg. What is the temperature, specific volume, enthalpy, and entropy?arrow_forward4-Steam flows through a device with a stagnation pressure of 120 psia, a stagnation temperature of 7008F, and a velocity of 900 ft/s. Assuming ideal- gas behavior, determine the static pressure and temperature of the steam at this state.arrow_forwardQUESTION 6 Air enters a diffuser with an averaged velocity of 360 m/s at a temperature of 340 kPa and 420 K and leaves at a stagnation pressure of 300 kPa with an averaged velocity of 120 m/s and a static pressure of 285 kPa. Determine, stagnation pressure and (i) the static pressure and Mach number of the air at inlet; (ii) the diffuser efficiency (iii the Mach number at exit and the overall entropy increasearrow_forward
- Steam at a pressure of 0.90 Mpa has entropy of 4.9678 kJ/kg (K). What are the specific volume, internal energy, and enthalpy?arrow_forward4. A converging nozzle is fed with air from a large reservoir where the. pressure and temperature are 250 kPa and 300 K, respectively. If the nozzle discharges to a region where the pressure is 100 kPa, determine the pressure and cross-sectional area at the exit of the nozzle. Assume that the flow is reversible and adiabatic with a mass flow rate of 10 kg-s". (100 kPa, 0.01714 m)arrow_forward5- An aircraft is flying at an altitude of (12000 m) (T = 216.65 k, P = 0.193bar) at a Mach number of (0.82). The cross-sectional area of the inlet diffuser is (0.5 m2).Determine: (a) The mass of air entering the compressor per second. (b) The speed of aircraft. (c) The stagnation pressure and temperature of air at the diffuser entry.arrow_forward
- A 5-feet diameter Chimney is designed to handle a flue gas produced in a steam power plant at a rate of 17 lb/s. The barometric pressure is 29.92-inch Hg. Outside air enters the combustion chamber at 90 F. The average temperature of the flue gas inside the Chimney is 572 F and its molecular weight is 30. Cv = 0.35, Rair = 53.342 ft-lb/lb-R. Calculate: a. The total draft, feet of air. b. The height of the Chimney, feetarrow_forwardQ-3/ A vessel is divided equally in two parts. The first part is evacuated, while the second part of the tank contains 2.5 kg of compressed liquid water at a pressure of 4 bar and temperature 333 kelvin. The partition is now removed, and the water expands to fill the entire tank. During this process, estimate the entropy change of water and the heat, if the final pressure in the tank is 40 КРа.arrow_forwardThe mass flow rate of gas entering nozzle is 25 /m3 . The inlet total pressure= 200kPa and inlet total temperature = 900 K. The exit pressure = 80 kPa ,and isentropic efficiency =92%.Determine the density of gases at the exit and the exit area . (Specific heat is 1100 J/kg.K and gas constant 287 J/kg.K ).arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Power Plant Explained | Working Principles; Author: RealPars;https://www.youtube.com/watch?v=HGVDu1z5YQ8;License: Standard YouTube License, CC-BY