![EBK FLUID MECHANICS: FUNDAMENTALS AND A](https://www.bartleby.com/isbn_cover_images/8220103676205/8220103676205_largeCoverImage.jpg)
EBK FLUID MECHANICS: FUNDAMENTALS AND A
4th Edition
ISBN: 8220103676205
Author: CENGEL
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Question
Chapter 12, Problem 145P
To determine
An expression for the stagnation pressure ratio after a shock wave to the static pressure before the shock wave as a function of
Expert Solution & Answer
![Check Mark](/static/check-mark.png)
Want to see the full answer?
Check out a sample textbook solution![Blurred answer](/static/blurred-answer.jpg)
Students have asked these similar questions
Find the expression for the ratio of the stagnation pressure after a shock wave to the static pressure before the shock wave as a function of k and the Mach number upstream of the shock wave Ma1
In a wind tunnel air enters with a velocity of 200kmph. The static pressure and temperature of the air at the inlet of the tunnel is 110kPa and 27°C respectively. Determine Mach number, stagnation temperature, stagnation pressure and the stagnation density on a test model installed in the wind tunnel. The size of the tunnel is given as 1m x1m square cross-section. Determine the mass flow rate of the air. For air assume R=287J/kgK ; γ=1.4.
2. Determine the final Mach number and density
in the compressive case with an initial Mach
number of 1.75 and a deflection of 10° using the
exact theory method. Assume normal sea-level
conditions.
Chapter 12 Solutions
EBK FLUID MECHANICS: FUNDAMENTALS AND A
Ch. 12 - What is dynamic temperature?Ch. 12 - Calculate the stagnation temperature and pressure...Ch. 12 - Prob. 6PCh. 12 - Prob. 7PCh. 12 - Prob. 8EPCh. 12 - Prob. 9PCh. 12 - Products of combustion enter a gas turbine with a...Ch. 12 - Is it possible to accelerate a gas to a supersonic...Ch. 12 - Prob. 72EPCh. 12 - Prob. 73P
Ch. 12 - Prob. 74PCh. 12 - Prob. 75PCh. 12 - For an ideal gas flowing through a normal shock,...Ch. 12 - Prob. 77CPCh. 12 - On a T-s diagram of Raleigh flow, what do the...Ch. 12 - What is the effect of heat gain and heat toss on...Ch. 12 - Prob. 80CPCh. 12 - Prob. 81CPCh. 12 - Prob. 82CPCh. 12 - Argon gas enters a constant cross-sectional area...Ch. 12 - Prob. 84EPCh. 12 - Prob. 85PCh. 12 - Prob. 86PCh. 12 - Prob. 87EPCh. 12 - Prob. 88PCh. 12 - Prob. 89PCh. 12 - Prob. 90PCh. 12 - Prob. 91PCh. 12 - Prob. 93CPCh. 12 - Prob. 94CPCh. 12 - Prob. 95CPCh. 12 - Prob. 96CPCh. 12 - Prob. 97CPCh. 12 - Prob. 98CPCh. 12 - Prob. 99CPCh. 12 - Prob. 100CPCh. 12 - Prob. 101PCh. 12 - Air enters a 5-cm-diameter, 4-m-long adiabatic...Ch. 12 - Helium gas with k=1.667 enters a 6-in-diameter...Ch. 12 - Air enters a 12-cm-diameter adiabatic duct at...Ch. 12 - Prob. 105PCh. 12 - Air flows through a 6-in-diameter, 50-ft-long...Ch. 12 - Air in a room at T0=300k and P0=100kPa is drawn...Ch. 12 - Prob. 110PCh. 12 - Prob. 112PCh. 12 - Prob. 113PCh. 12 - Prob. 114PCh. 12 - Prob. 115PCh. 12 - Prob. 116EPCh. 12 - A subsonic airplane is flying at a 5000-m altitude...Ch. 12 - Prob. 118PCh. 12 - Prob. 119PCh. 12 - Prob. 120PCh. 12 - Prob. 121PCh. 12 - Prob. 122PCh. 12 - Prob. 123PCh. 12 - An aircraft flies with a Mach number Ma1=0.9 at an...Ch. 12 - Prob. 125PCh. 12 - Helium expands in a nozzle from 220 psia, 740 R,...Ch. 12 - Prob. 127PCh. 12 - Prob. 128PCh. 12 - Prob. 129PCh. 12 - Prob. 130PCh. 12 - Prob. 131PCh. 12 - Prob. 132PCh. 12 - Prob. 133PCh. 12 - Prob. 134PCh. 12 - Prob. 135PCh. 12 - Prob. 136PCh. 12 - Prob. 137PCh. 12 - Prob. 138PCh. 12 - Air is cooled as it flows through a 30-cm-diameter...Ch. 12 - Prob. 140PCh. 12 - Prob. 141PCh. 12 - Prob. 142PCh. 12 - Prob. 145PCh. 12 - Prob. 148PCh. 12 - Prob. 149PCh. 12 - Prob. 150PCh. 12 - Prob. 151PCh. 12 - Prob. 153PCh. 12 - Prob. 154PCh. 12 - Prob. 155PCh. 12 - Prob. 156PCh. 12 - Prob. 157PCh. 12 - Prob. 158PCh. 12 - Prob. 159PCh. 12 - Prob. 160PCh. 12 - Prob. 161PCh. 12 - Prob. 162PCh. 12 - Assuming you have a thermometer and a device to...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Q4//B/ Heat is removed from airflow in a constant-area duct, if flow enters at Mach 2.20, T1= 310 K, and p1= 120 kPa. Determine exit Mach number and the amount of heat removing from the duct if the static temperature at exit section is 255 K. justify your solution for M2arrow_forwardUsing the Image below solve the following two questions, AND ONLY SOLVE FOR i and iii a.Determine The total pressure loss in the final state, after the 20 degree turn, for i and iii. (I'd also like to confirm for ii that the total pressure loss is 0?) b.Determine the Mach number in the final state. For which geometry is this highest? ( For ii it is 2.12)arrow_forwarddetermine the Mach number, total pressure, and total temperature after the heat interaction for the following gases: a) y= 1.4 and cp 0.24 Btu/(lbm- °R) b) y= 1.325 and cp = 0.28 Btu/(1bm · °R) %3Darrow_forward
- Q4/ Air enters a duct with a Mach number of 2.0, and the temperature and pressure are 170 K and 0.7 bar, respectively. Heat transfer takes place while the flow proceeds down the duct. A converging section (A2/A3 = 1.45) is attached to the outlet as shown in Fig. Q4, and the exit Mach number is 1.0. Assume that the inlet conditions and exit Mach number remain fixed. Find the amount and direction of heat transfer in the duct: (a) If there are no shocks in the system. (b) If there is a normal shock someplace in the duct. M, - 2.0 T,- 170 K P-0.7 bar M, = 1.0 Fig.Q4 AzlA, = 1.45arrow_forwardQ1: when aircraft is ffying at subsonic velocity, the pressure at its nose i e. the stagnation point is found to be 160 kpa. if the ambient pressure and temperature are 100 kpa and 298k respectively, find the speed and Mach number at which the aircraft is flying.-arrow_forwardRewrite dV/V in terms of only Mach number and γ for a steady, adiabatic flow. Showall steps of the derivation clearly. γ = 1.4, R=287 J/kgKarrow_forward
- Using the Image below solve the following two questions, AND ONLY SOLVE FOR i and iii a.Determine The total pressure loss in the final state, after the 20 degree turn, for i and iii. (I'd also like to confirm for ii that the total pressure loss is 0?) b.Determine the Mach number in the final state. For which geometry is this highest? ( For ii it is 2.12) ALSO USE THE OTHER PICTURE WITH TABLES TO HELP YOU ANSWERarrow_forwardThe Mach number of an aircraft that travels with a speed of 260 m/s in air at 25° C while it undergoes the compressibility effect will be: (Use speed of sound in air at 0° C: 331 m/s) Select one: a. M = 0.69 b. M= 0.70 c. M= 0.75arrow_forwardA normal shock occurs in a stream of oxygen. The oxygen flows at Ma=1.8 and the upstream pressure and temperature are 40 psia and 85 degrees Fahrenheit. a) Calculate the following on the downstream side of the shock: static pressure, stagnation pressure, static temperature, stagnation temperature, static density, and velocity. b)If the Mach number is doubled to 3.6, what will be the resulting values of the parameters listed in part (a)?arrow_forward
- What is the Mach number of an airflow with a velocity of 2000m/s, at 2,000 ft altitude?arrow_forwardFind the velocity of bullet fired in standard air if the Mach angle is 45°. Take R=287.14 J/kg K and k = 1.4 for air. Assume temperature as 27°Carrow_forwardWhat is the Mach Number of an air with a velocity of 250 m/s, at a temperature at 2800 meters?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
![Text book image](https://www.bartleby.com/isbn_cover_images/9780190698614/9780190698614_smallCoverImage.gif)
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
![Text book image](https://www.bartleby.com/isbn_cover_images/9780134319650/9780134319650_smallCoverImage.gif)
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
![Text book image](https://www.bartleby.com/isbn_cover_images/9781259822674/9781259822674_smallCoverImage.gif)
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
![Text book image](https://www.bartleby.com/isbn_cover_images/9781118170519/9781118170519_smallCoverImage.gif)
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
![Text book image](https://www.bartleby.com/isbn_cover_images/9781337093347/9781337093347_smallCoverImage.gif)
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
![Text book image](https://www.bartleby.com/isbn_cover_images/9781118807330/9781118807330_smallCoverImage.gif)
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License