Concept explainers
(III) A door 2.30 m high and 1.30 m wide has a mass of 13.0 kg. A hinge 0.40 m from the top and another hinge 0.40 m from the bottom each support half the door’s weight (Fig. 12–66). Assume that the center of gravity is at the geometrical center of the door, and determine the horizontal and vertical force components exerted by each hinge on the door.
FIGURE 12–66 Problem 29.
Want to see the full answer?
Check out a sample textbook solutionChapter 12 Solutions
Modified Mastering Physics With Pearson Etext -- Standalone Access Card -- For Physics For Scientists & Engineers With Modern Physics (5th Edition)
Additional Science Textbook Solutions
Modern Physics
Sears And Zemansky's University Physics With Modern Physics
College Physics: A Strategic Approach (3rd Edition)
Conceptual Integrated Science
An Introduction to Thermal Physics
Lecture- Tutorials for Introductory Astronomy
- A wooden door 2.1 m high and 0.90 m wide is hung by two hinges 1.8 m apart. The lower hinge is 15 cm above the bottom of the door. The center of mass of the door is at its geometric center, and the weight of the door is 260 N, which is supported equally by both hinges. Find the horizontal force exerted by each hinge on the door.arrow_forwardA uniform horizontal strut weighs 400.0 N. One end of the strut is attached to a hinged support the wall and the other end of the strut is attached to a sign that weighs 200.0 N The strut is also supported by a cable attached between the end of the strut and the wall. Assuming that the entire weight of the sign is attached at the very end of the s find the tension in the cable and the force at the hinge of the strut.arrow_forwardIn Figure 9.21, the cg of the pole held by the pole vaulter is 2.00 m from the left hand, and the hands are 0.700 m apart. Calculate the force exerted by (a) his right hand and (b) his left hand. (c) If each hand supports half the weight of the pole in Figure 9.19, show that the second condition for equilibrium (net =0 ) is satisfied for a pivot other than the one located at the center of gravity of the pole. Explicitly show how you follow the steps in the Problem-Solving Strategy for static equilibrium described above. Figure 9.21 A pole vaulter is holding a pole horizontally with both hands. The center of gravity is to the left side of the vaulter.arrow_forward
- When the structure shown below is supported at point P, it is in equilibrium. Find the magnitude .of force F and the force applied at P. the weight of the structure is negligible.arrow_forward(24) Assuming the lower arm has a mass of 2.8 kg and its CG is 12 cm from the elbow- joint pivot, how much force must the extensor muscle in the upper arm exert on the lower arm to hold a 7.5 kg shot put (Fig. 12-7)? 11) 2.5 cm F M A) 100 N 30.0 cm- Elbow joint B) 750 N C) 1500 N D) 500 N E) 1000 Narrow_forwardA uniform beam is hinged at one end and held in a hori- zontal position by a cable, as shown in Fig. 9–42. The tension in the cable (a) must be at least half the weight of the beam, no matter what the angle of the cable. (b) could be less than half the beam's weight for some angles. (c) will be half the beam's weight for all angles. (d) will equal the beam's weight for all angles. FIGURE 9–42 MisConceptual Question 3: beam and cable.arrow_forward
- (11) A tapered log 3.0 m long weighs 210 N and has its center of gravity 1.0 m from the thick end. It is being used as a bridge across a ditch and is supported at its ends by the edges of the ditch. A 600 N man stands on the log 1.0 m from the thin end. How much support is required at each end of the log? 3m FN=mant eug+ 1.omarrow_forward(I) A sign (mass 1700 kg) hangs from the bottom end of avertical steel girder with a cross-sectional area of 0.012 m2(a) What is the stress within the girder? (b) What is thestrain on the girder? (c) If the girder is 9.50 m long, howmuch is it lengthened? (Ignore the mass of the girder itself.)arrow_forward(II) A 20.0-m-long uniform beam weighing 650 N rests on walls A and B, as shown in Fig. 9–62. (a) Find the maxi- mum weight of a person who can walk to the extreme end D without tipping the beam. Find the forces that the walls A and B exert on the beam when the person is stand- ing: (b) at D; (c) 2.0 m to the right of A. - 20.0 m- A В D +3.0 m→ -12.0 m - FIGURE 9-62 Problem 22.arrow_forward
- 10) One end of a uniform beam is hinged to a wall and the other end is supported by a tension wire that makes angles 0 = 25° with both the wall and the beam as shown in the figure below. The beam is 1 m long and weighs 222 N with its center of mass located at the half of its total length. Find (a) the tensile force in the wire, (b) the horizontal component of the force of the hinge on the beam, and (c) the vertical component of the force of the hinge on the beam. Hingearrow_forward- 5. Two identical, uniform beams of length 3 m and weighing 260 N each are connected at one end by a frictionless hinge. A light horizontal crossbar, attached at the midpoints of the beams maintains an angle 50° between the beams. The beams are suspended from the ceiling by vertical wires so they form a V. See figure. (a) What force does the crossbar exert on each beam? (b) Is the crossbar under compression or tension, i.e. are the ends of the crossbar being pushed together or stretched farther apart? (c) What force (magnitude and direction) does the hinge exert on each beam? Crossbar Hingearrow_forward(II) A uniform steel beam has a mass of 940 kg. On it is resting half of an identical beam, as shown in Fig. 9-60. What is the vertical support force at each end? •M •Marrow_forward
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage LearningUniversity Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice UniversityCollege PhysicsPhysicsISBN:9781938168000Author:Paul Peter Urone, Roger HinrichsPublisher:OpenStax College