Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 12, Problem 2TF
True False? Camshaft straightness is checked using V-blocks and a feeler gauge?
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
List six checks that should be carried out when inspecting camshafts
Technician A says that an in-line six-cylinder diesel engine is usually longer and heavier than a V8 engine of the same displacement. Technician B says that there are twice as many teeth on the crankshaft as there are on the camshaft sprocket.
Who is correct? and why?
Technician A
Technician B
Both A and B
Neither A nor B
True or False? The camshaft is always locatedin the engine block.
Chapter 12 Solutions
Automotive Technology
Ch. 12 - Explain staged and continuously variable value...Ch. 12 - Prob. 2SACh. 12 - Define valve margin.Ch. 12 - What usually causes warpage in an aluminum cylin...Ch. 12 - What are the two ways pushrods can be checked for...Ch. 12 - True False? Fiats MultiAir system relies on...Ch. 12 - True False? Camshaft straightness is checked using...Ch. 12 - Which of the following is not true of knurling? It...Ch. 12 - To allow the engine to run on the Atkinson cycle,...Ch. 12 - To ensure proper seating of the valve, the valve...
Ch. 12 - Many engines with WT have a phaser mounted to the...Ch. 12 - Multiple valve engines tend to be more efficient...Ch. 12 - Which of the following is not a type of valve...Ch. 12 - What type of valve lifter automatically...Ch. 12 - Prob. 8MCCh. 12 - While discussing the reasons for resurfacing a...Ch. 12 - While inspecting the timing gears of an engine:...Ch. 12 - Technician A says that positive valve stem seals...Ch. 12 - Prob. 4ASRQCh. 12 - Technician A says an engine may use one or more...Ch. 12 - Technician A says it is not necessary to measure...Ch. 12 - While discussing the Valvetronic system:...Ch. 12 - While checking a hydraulic phaser after the...Ch. 12 - While servicing a pair of aluminum cylinder heads:...Ch. 12 - While discussing camshafts Technician A says valve...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- True or False? The camshaft is always located in the engine block.arrow_forwardWhile discussing camshafts Technician A says valve lift is based only on the height of the cam lobe. Technician B says valve duration is based on the height of the lobe. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardWhile diagnosing the cause for an engine having good results from a compression test and cylinder leakage test but poor results from a cylinder power balance test: Technician A says that incorrect valve timing is the most likely cause. Technician B says that a severely worn cam lobe is a likely cause. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- True or False? Some crankshaft and camshaft timing sensors have a specified gap that must be set during installation.arrow_forwardWhile driving straight, a FWD car pulls to the right. The most likely cause is. more positive camber on the left front wheel compared to the right front wheel sagged front springs and improper front-wheel toe setting less positive caster on the right front wheel compared to the left front wheel the SAI on the right front wheel is 1*A degrees more than the SAI on the left.arrow_forwardTechnician A says off-square springs may cause increased stem-to-guide wear. Technician B says excessive spring tension may cause premature camshaft wear. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- (A)What are the fuctions of engine camshaft and cranck shaft.arrow_forwardTech A states to check the camshaft for lift, the cam must be removed from the engine. Tech B says to check for a bent camshaft, the cam must be removed and placed onto a set of V-blocks and checked with a dial indicator. Who is correct?arrow_forwardTechnician A checks crankshaft oil clearance with a feeler gauge. Technician B uses a dial indicator to check crankshaft oil clearance. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- True or False? Valve lash is adjusted in many different ways; however, on many OHC engines, the clearance is set by replacing a shim.arrow_forwardTechnician A says that negative caster provides directional stability . Technician B says that pos caster results from excessive positive cam ber . Who is correct ?arrow_forwardWhen removing the balance shaft assembly: tech a inspects the bearings for unusual wear or damage. Tech b smoothens a damaged camshaft or balance shaft journal by lightly sanding it. Who is correct?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY