Fundamentals Of Physics - Volume 1 Only
11th Edition
ISBN: 9781119306856
Author: Halliday
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 12, Problem 48P
Figure 12-59 shows the stress versus strain plot for an aluminum wire that is stretched by a machine pulling in opposite directions at the two ends of the wire. The scale of the stress axis is set by s = 7.0, in units of 107 N/m2. The wire has an initial length of 0.800 m and an initial cross-sectional area of 2.00 × 10−6 m2. How much work does the force the machine do on the wire to produce a strain of 1.00 × 10−3?
Figure 12-59 Problem 48.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The upper surface of a cube of gelatin, 5.0 cm on a side, is displaced by 0.64 cm by a tangential force. If the shear modulus of the gelatin is 940 Pa, what is the magnitude of the tangential force?
An aluminum (ρ = 2.7 g/cm3) wire is suspended from the ceiling and hangs vertically. How long must the wire be before the stress at its upper end reaches the proportionality limit, which is 8.0 × 107 N/m2 ?
In her gymnastic routine, Regina dismounts from the uneven-parallel bars and lands straight-legged on the ground, compressing her 0.250 m long femur by 2.10×10^(-5) m. If the femur has a cross-sectional area of 3.00×10^(-4) m^2 and the stress modulus of bone is 2.00×10^10 N/m^2, with how much force does Regina hit the ground?
a. 550 N
b. 632 N
c. 504 N
d. 409 N
e. None of the above
Chapter 12 Solutions
Fundamentals Of Physics - Volume 1 Only
Ch. 12 - Figure 12-15 shows three situations in which the...Ch. 12 - In Fig, 12-16, a rigid beam is attached to two...Ch. 12 - Figure 12-17 shows four overhead views of rotating...Ch. 12 - A ladder leans against a frictionless wall but is...Ch. 12 - Figure 12-18 shows a mobile of toy penguins...Ch. 12 - Figure 12-19 shows an overhead view of a uniform...Ch. 12 - Prob. 7QCh. 12 - Three piatas hang from the stationary assembly of...Ch. 12 - In Fig. 12-22, a vertical rend is hinged at its...Ch. 12 - Figure 12-23 shows a horizontal block that is...
Ch. 12 - The table gives the initial lengths of three reds...Ch. 12 - A physical therapist gone wild has constructed the...Ch. 12 - Prob. 1PCh. 12 - An automobile with a mass of 1360 kg has 3.05 m...Ch. 12 - SSM WWWIn Fig. 12-26, a uniform sphere of mass m =...Ch. 12 - An archers bow is drawn at its midpoint until the...Ch. 12 - ILWA rope of negligible mass is stretched...Ch. 12 - A scaffold of mass 60 kg and Length 5.0 m is...Ch. 12 - A 75 kg window cleaner uses a 10 kg ladder that is...Ch. 12 - A physics Brady Bunch, whose weights in newtons...Ch. 12 - SSMA meter stick balances horizontally on a...Ch. 12 - GO The system in Fig. 12-28 is in equilibrium,...Ch. 12 - SSMFigure 12-29 shows a diver of weight 580 N...Ch. 12 - In Fig. 12-30, trying to gel his car out of mud, a...Ch. 12 - Figure 12-31 shows the anatomical structures in...Ch. 12 - In Fig. 12-32, a horizontal scaffold, of length...Ch. 12 - ILWForces F1, F2 and F3 act on the structure of...Ch. 12 - A uniform cubical crate is 0.750 m on each side...Ch. 12 - In Fig. 12-34, a uniform beam of weight 500 N and...Ch. 12 - GO In Fig. 12-35, horizontal scaffold 2, with...Ch. 12 - To crack a certain nut in a nutcracker, forces...Ch. 12 - A bowler holds a bowling ball M = 7.2 kg in the...Ch. 12 - ILWThe system in Fig. 12-38 is in equilibrium. A...Ch. 12 - GO In Fig-12-39, a 55 kg rock climber is in a...Ch. 12 - GO In Fig. 12-40, one end of a uniform beam of...Ch. 12 - GO In Fig. 12-41, a climber with a weight of 533.8...Ch. 12 - SSM WWWIn Fig. 12-42, what magnitude of constant...Ch. 12 - GO In Fig. 12-43, a climber leans out against a...Ch. 12 - GO In Fig. 12-44, a 15 kg block is held in place...Ch. 12 - GO In Fig. 12-45, suppose the length L of the...Ch. 12 - A door has a height of 2.1 m along a y axis that...Ch. 12 - GO In Fig. 12-46, a 50.0 kg uniform square sign,...Ch. 12 - GO In Fig. 12-47, a nonuniform bar is suspended at...Ch. 12 - In Fig. 12-48, the driver of a car on a horizontal...Ch. 12 - Figure 12-49a shows a vertical uniform beam of...Ch. 12 - In Fig. 12-45, a thin horizontal bar AB of...Ch. 12 - SSM WWWA cubical box is filled with sand and...Ch. 12 - Figure 12-50 shows a 70 kg climber hanging by only...Ch. 12 - GO In Fig. 12-51, a uniform plank, with a length L...Ch. 12 - In Fig, 12-52, uniform beams A and B are attached...Ch. 12 - For the stepladder shown in Fig. 12-53, sides AC...Ch. 12 - Figure 12-54a shows a horizontal uniform beam of...Ch. 12 - A crate, in the form of a cube with edge lengths...Ch. 12 - In Fig. 12-7 and the associated sample problem,...Ch. 12 - SSM ILWA horizontal aluminum rod 4.8 cm in...Ch. 12 - Figure 12-55 shows the stressstrain curve for a...Ch. 12 - In Fig. 12-56, a lead brick rests horizontally on...Ch. 12 - Figure 12-57 shows an approximate plot of stress...Ch. 12 - A tunnel of length L = 150 m, height H = 7.2 m,...Ch. 12 - Figure 12-59 shows the stress versus strain plot...Ch. 12 - GO In Fig. 12-60, a 103kg uniform log hangs by two...Ch. 12 - GO Figure 12-61 represents an insect caught at the...Ch. 12 - GO Figure 12-62 is an overhead view of a rigid rod...Ch. 12 - After a fall, a 95 kg rock climber finds himself...Ch. 12 - SSMIn Fig 12-63, a rectangular slab of slate rests...Ch. 12 - A uniform ladder whose length is 5.0 m and whose...Ch. 12 - SSM In Fig. 12-64, block A mass 10 kg is in...Ch. 12 - Figure 12-65a shows a uniform ramp between two...Ch. 12 - GO In Fig. 12-66, a 10 kg sphere is supported on a...Ch. 12 - In Fig. 12-67a, a uniform 40.0 kg beam is centered...Ch. 12 - SSM In Fig. 12-68, an 817 kg construction bucket...Ch. 12 - In Fig. 12-69, a package of mass m hangs from a...Ch. 12 - ILWThe force F in Fig. 12-70 keeps the 6.40 kg...Ch. 12 - A mine elevator is supported by a single steel...Ch. 12 - Four bricks of length L, identical and uniform,...Ch. 12 - Prob. 64PCh. 12 - In Fig. 12-73, a uniform beam with a weight of 60...Ch. 12 - A uniform beam is 5.0 m long and has a mass of 53...Ch. 12 - A solid copper cube has an edge length of 85.5 cm....Ch. 12 - A construction worker attempts to lift a uniform...Ch. 12 - SSM In Fig. 12-76, a uniform rod of mass m is...Ch. 12 - A 73 kg man stands on a level bridge of length L....Ch. 12 - SSMA uniform cube of side length 8.0 cm rests cm a...Ch. 12 - The system in Fig. 12-77 is in equilibrium. The...Ch. 12 - SSMA uniform ladder is 10 m long and weighs 200 N....Ch. 12 - A pan balance is made up of a rigid, massless rod...Ch. 12 - The rigid square frame in Fig. 12-79 consists of...Ch. 12 - A gymnast with mass 46.0 stands on the end of a...Ch. 12 - Figure 12-81 shows a 300 kg cylinder that is...Ch. 12 - In Fig. 12-82, a uniform beam of length 12.0 m is...Ch. 12 - Four bricks of length L, identical and uniform,...Ch. 12 - A cylindrical aluminum rod, with an initial length...Ch. 12 - Prob. 81PCh. 12 - If the square beam in Fig. 12-6a and the...Ch. 12 - Figure 12-84 shows a stationary arrangement of two...Ch. 12 - A makeshift swing is constructed by makings loop...Ch. 12 - Figure 12-85a shows details of a finger in the...Ch. 12 - A trap door in a ceiling is 0.91 m square, has a...Ch. 12 - A particle is acted on by forces given, in...Ch. 12 - The leaning Tower of Pisa is 59.1 m high and 7.44...
Additional Science Textbook Solutions
Find more solutions based on key concepts
The volume charge density of a spherical charge distribution is given by p(r)=p0ear , where p0 , and a are cons...
University Physics Volume 2
Suppose the red and blue beams of Exercise 26 are now propagating in the same direction inside the glass. For w...
Essential University Physics (3rd Edition)
Choose the best answer to each of the following. Explain your reasoning. In which of these possible models for ...
Cosmic Perspective Fundamentals
26. The mass in a pendulum clock completes one complete swing in 1.00 s. What is the length of the rod?
College Physics: A Strategic Approach (3rd Edition)
Just beneath Point I on the drawing is a tropical island. What will eventually happen to the island as the ocea...
Lecture- Tutorials for Introductory Astronomy
The effect on electric generator due to an increase in the length of wire of an armature.
Glencoe Physics: Principles and Problems, Student Edition
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- A uniform wire (Y = 2.0 1011 N/m2) is subjected to a longitudinal tensile stress of 4.0 107 N/m2. What is the fractional change in the length of the wire?arrow_forwardA steel cable 2.00 m in length and with cross-sectional radius 0.350 mm is used to suspend from the ceiling a 10.0-kg model aircraft that is flying in a horizontal circle with an angular speed of 6.00 rad/s. What is the strain produced in the cable?arrow_forwardAlarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?arrow_forward
- Two rods, one made of copper and the other of steel, have the same dimensions. If the copper rod stretches by 0.15mm under some stress, how much does the steel rod stretch under the same stress?arrow_forwardA material of Poisson's ratio 0.5. If a uniform rod it suffers a longitudinal strain of 2*10 -3, what is the percentage increase in volume?arrow_forwardA 1.25 m long cable has a diameter 3.50 mm with a Young’s Modulus, E, of 9.75 x 109 N/m2 . When the wire is placed under tension, it experiences a stress of 202.52 x 106 N/m2 , the length of the cable extends by 36.35 mm. Calculate the force that the cable experiences under tension and the strain energy density (U/V) due to deformation. Give your answers in newtons (N) to 2 decimal places for the force; and in joules per cubic metre (J/m3 ) for the strain energy density to 2 decimal places. Assume the cable is solid and the material is homogeneous.arrow_forward
- A wire of uniform 1mm ^ 2 radius is fixed at its top end and has a weight tied at the other end. If the strain energy per unit volume is 2 × 10 ^ 4 hertz⁄ cm^3 ,and the increase in length per unit length is 2 × 10 ^ (- 4). Calculate (a) Young's modulus (b) stress (c) tensile forcearrow_forwardsuppose the length L of the uniform bar is 3.4 m and its weight is 180 N. Also, let the block's weight W = 310 N and the angle 0 = 41°. The wire can withstand a maximum tension of 440 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A?arrow_forwardthe drawing shows a 150 kg crate hanging from one end of steel bar (S= 8.1 x10^10 n/m^2) The length of the bar is 0.428 m and its cross-sectional area is 7.94 x 10 ^-4 m^2. Neglect the weight of the bar itself and determine (a) the shear stress on the bar and (b) the vertical deflection deltaY of the right end of the bar.arrow_forward
- A 15 cm long animal tendon ( وتر ) was found to stretch 3.7 mm by a force of 13.4 N. The tendon was approximately round with an average diameter of 8.5 mm. the elastic modulus of this tendon?arrow_forwardDetermine the moment M that will produce a maximum stress of 70 MPa on the cross-section.arrow_forwardRubber has a Young's modiles of 1.5 x 10^8 Pa. If someone were to apply a force of 3 x 10^10 N to the side of a 12 m^3 cube, what would the strain on the cube of rubber bearrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage LearningUniversity Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice University
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
University Physics Volume 1
Physics
ISBN:9781938168277
Author:William Moebs, Samuel J. Ling, Jeff Sanny
Publisher:OpenStax - Rice University
An Introduction to Stress and Strain; Author: The Efficient Engineer;https://www.youtube.com/watch?v=aQf6Q8t1FQE;License: Standard YouTube License, CC-BY