Concept explainers
A 0.5-kg block B slides without friction inside a slot cut in arm OA that rotates in a vertical plane. The rod has a constant angular acceleration
Fig. P12.69
Want to see the full answer?
Check out a sample textbook solutionChapter 12 Solutions
Vector Mechanics for Engineers: Statics and Dynamics
Additional Engineering Textbook Solutions
Engineering Mechanics: Dynamics (14th Edition)
Fundamentals of Heat and Mass Transfer
Engineering Mechanics: Statics
DESIGN OF MACHINERY
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
Vector Mechanics for Engineers: Statics, 11th Edition
- A spring AB of constant k is attached to a support at A and to a collar of mass m. The unstretched length of the spring is 1 . Knowing that the collar is released from rest at x=x0 and neglecting friction between the collar and the horizontal rod, determine the magnitude of the velocity of the collar as it passes through point C.arrow_forwardCollar A has a mass of 3 kg and is attached to a spring of constant 1200 N/m and of undeformed length equal to 0.5 m. The system is set in motion with r= 0.3 m, v0 = 2 m/s, and vr = 0. Neglecting the mass of the rod and the effect of friction, determine the radial and transverse components of the velocity of the collar when r= 0.6 m.arrow_forwardA 2000-kg automobile starts from rest at point A on a 6° incline and coasts through a distance of 50 m to point B. The brakes are then applied, causing the automobile to come to a stop at point C, 20 m from B. Knowing that slipping is impending during the braking period and neglecting air resistance and rolling resistance, determine the speed of the automobile at point B. The speed of the automobile at point B is ___ m/s.arrow_forward
- Two hemispheres are held together by a cord which maintains a spring under compression (the spring is not attached to the hemispheres). The potential energy of the compressed spring is 120 J and the assembly has an initial velocity v0 of magnitude v0 = 8 m/s. Knowing that the cord is severed when 0 = 30°, causing the hemispheres to fly apart, determine the resulting velocity of each hemisphere.arrow_forwarda 400-kg satellite was place in a circular orbit 1500 km above the surface of the earth at this elevation the acceleration of gravity is 6.43 m/s^2 determine the kinetic energy of the satellite in kJ knowing that its orbital speed is 25.6x10^3 km/harrow_forwardA 1-lb ball A and a 2-lb ball B are mounted on a horizontal rod that rotates freely about a vertical shaft. The balls are held in the positions shown by pins. The pin holding B is suddenly removed and the ball moves to position C as the rod rotates. Neglecting friction and the mass of the rod and knowing that the initial speed of A is vA = 8 ft/s, determine (a) the radial and transverse components of the acceleration of ball B immediately after the pin is removed, (b) the acceleration of ball B relative to the rod at that instant, (c) the speed of ball A after ball B has reached the stop at C.arrow_forward
- A 2000-kg automobile starts from rest at point A on a 6° incline and coasts through a distance of 150 m to point B. The brakes are then applied, causing the automobile to come to a stop at point C , which is 20 m from B . Knowing that slipping is impending during the braking period and neglecting air resistance and rolling resistance, determine (a) the speed of the automobile at point B, (b) the coefficient of static friction between the tires and the road.arrow_forwardA spring AB of constant k=200kn/m is attached to a support at A and to a collar of mass m=200 gm. The unstretched length of the spring is I=0.6m. Knowing that the collar is released from rest at x0 = 80 cm and neglecting friction between the collar and the horizontal rod, determine :the magnitude of the velocity of the collar as it passes through point C.arrow_forwardA polisher is started so that the fleece along the circumference undergoes a constant tangential acceleration of 4 m/s2 . Three seconds after it is started, small tufts of fleece from along the circumference of the 225-mm-diameter polishing pad are observed to fly free of the pad. At this instant, determine (a) the speed v of a tuft as it leaves the pad, (b ) the magnitude of the force required to free a tuft if the average mass of a tuft is 1.6 mg.arrow_forward
- To unload a bound stack of plywood from a truck, the driver first tilts the bed of the truck and then accelerates from rest. Knowing that the coefficients of friction between the bottom sheet of plywood and the bed are μs= 0.40 and μk= 0.30, determine (a) the smallest acceleration of the truck which will cause the stack of plywood to slide, (b) the acceleration of the truck which causes corner A of the stack to reach the end of the bed in 0.9 s.arrow_forwardA 500-g collar can slide without friction on the curved rod BC in a horizontal plane. Knowing that the undeformed length of the spring is 80 mm and that k= 400 kN/m, determine (a) the velocity that the collar should be given at A to reach B with zero velocity, (b) the velocity of the collar when it eventually reaches C.arrow_forwardA bowler projects an 8-in.-diameter ball weighing 12 lb along an alley with a forward velocity v0 of 15 ft/s and a backspin ω0 of 9 rad/s. Knowing that the coefficient of kinetic friction between the ball and the alley is 0.10, determine (a) the time t1 at which the ball will start rolling without sliding, (b) the speed of the ball at time t1, (c) the distance the ball will have traveled at time t1arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY