Concept explainers
Pin B weighs 4 oz and is free to slide in a horizontal plane along the rotating arm OC and along the fixed circular slot DE of radius b = 20 in. Neglecting friction and assuming that
Fig. P12.70
Want to see the full answer?
Check out a sample textbook solutionChapter 12 Solutions
Vector Mechanics for Engineers: Statics and Dynamics
Additional Engineering Textbook Solutions
Mechanics of Materials
Fluid Mechanics Fundamentals And Applications
Fox and McDonald's Introduction to Fluid Mechanics
HEAT+MASS TRANSFER:FUND.+APPL.
Applied Fluid Mechanics (7th Edition)
Introduction to Heat Transfer
- Collar A has a mass of 3 kg and is attached to a spring of constant 1200 N/m and of undeformed length equal to 0.5 m. The system is set in motion with r= 0.3 m, v0 = 2 m/s, and vr = 0. Neglecting the mass of the rod and the effect of friction, determine the radial and transverse components of the velocity of the collar when r= 0.6 m.arrow_forwardA light train made up of two cars is traveling at 90 km/h when the brakes are applied to both cars. Knowing that car A has a mass of 25 Mg and car B a mass of 20 Mg, and that the braking force is 30 kN on each car, determine (a) the distance traveled by the train before it comes to a stop, (b) the force in the coupling between the cars while the train is slowing down.arrow_forwardThe double pulley shown in the figure has a mass of 3 kg and a radius of 100 mm rotation. Knowing that when the pulley is at rest, it is applied to the cable in B, a force P of magnitude equal to 24N, determine the speed of the center of the pulley after 1.5 s and the tensile force on cable C.arrow_forward
- A 5-kg collar A is at rest on top of, but not attached to, a spring with stiffness k1 = 400 N/m when a constant 150-N force is applied to the cable. Knowing A has a speed of 1 m/s when the upper spring is compressed 75 mm, determine the spring stiffness k2 . Ignore friction and the mass of the pulley.arrow_forwardA block of mass 20 kg is released from rest at the top of a ramp as shown in Figure 4. Thecoeficient of kinetic friction between block and ramp is μk = 0.25. When the block reaches thebottom ramp, it slides onto a belt moving to the right at constant speed, vc = 5 m/s. The kineticfriction coeficient between the block and belt is μk = 0.2. Determine the distance, d that theblock slides along the belt before the block’s velocity matches the velocity of the belt.arrow_forwardA pilot of mass m flies a jet in a half-vertical loop of radius R so that the speed of the jet, v , remains constant. Draw a FBD and KD of the pilot at points A, B, and c.arrow_forward
- To use the principle of work and energy to determine characteristics of a system of particles, including final velocities and positions. The two blocks shown have masses of mA = 56 kg and mB = 74 kg . The coefficient of kinetic friction between block A and the inclined plane is μk = 0.15 . The angle of the inclined plane is given by θ = 40 ∘ . Neglect the weight of the rope and pulley. Determine the magnitude of the normal force acting on block A, NA If both blocks are released from rest, determine the velocity of block B when it has moved through a distance of s = 2.00 m. If both blocks are released from rest, determine how far block A has moved up the incline when the velocity of block B is (vB)2 = 6.25 m/s.arrow_forwardA spring AB of constant k is attached to a support at A and to a collar of mass m. The unstretched length of the spring is 1 . Knowing that the collar is released from rest at x=x0 and neglecting friction between the collar and the horizontal rod, determine the magnitude of the velocity of the collar as it passes through point C.arrow_forwardFor the system of particles of Prob. 14.13, determine (a) the position vector r of the mass center G of the system, (b) the linear momentum mv of the system, (c) the angular momentum HG of the system about G . Also verify that the answers to this problem and to Problem 14.13 satisfy the equation given in Prob. 14.27.Reference to Problem 14.13:A system consists of three particles A, B, and C. We know that mA =3kg, mB =2kg, and mC = 4 kg and that the velocities of the particles expressed in m/s are, respectively, vA = 4i +2j +2k, vB = 4i + 3j, and vC = -2i + 4j +2k. Determine the angular momentum HO of the system about O.arrow_forward
- A spacecraft is placed into a polar orbit about the planet Mars at an altitude of 380 km. Knowing that the mean density of Mars is 3.94 Mg/m^3 and that the radius of Mars is 3397 km, determine the time t required for the spacecraft to complete one full revolution about Mars and the velocity with which the the spacecraft describes its orbit.arrow_forwardTwo spheres, each of mass m, can slide freely on a frictionless, horizontal surface. Sphere A is moving at a speed v0 = 16 ft/s when it strikes sphere B which is at rest, and the impact causes sphere B to break into two pieces, each of mass m/2.a) Knowing that 0.7 s after the collision one piece reaches Point C and 1.17 s after the collision the other piece reaches Point D, determine the velocity of sphere A after the collision.b) Knowing that 0.7 s after the collision one piece reaches Point C and 1.17 s after the collision the other piece reaches Point D, determine the angle θ and the speeds of the two pieces after the collision.arrow_forwardA 400-kg satellite was placed in a circular orbit 1500 km above the surface of the earth . At this elevation the acceleration of gravity is 6.43 m/s^2. Determine the kinetic energy of the satellite in kJ, knowing that its orbital speed is 25.6*10^ 3 km/h .arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY