AUTMOTIVE TECH, TECH MANUAL & MIND TAP
6th Edition
ISBN: 9781305383180
Author: ERJAVEC
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 13, Problem 8ASRQ
To determine
While tightening a TTY bolt: The technician with correct approach.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Technician A says a metric bolt with the marking of 8.9 has more yield strength than a 10.9 bolt. Technician B says only grade 8 nuts should be used on 10.9 rated bolt. Who is correct?
Which of the following is the most common method of snug tightening bolts?
O Heat tightening
O Tension Control Bolting
O Angle Tightening (Turn of Nut)
O Direct Tension Indicators
From the following identify a true statement regarding the adjustment of drive belt tension.
a.
Less than 8 mm should be the correct a deflection for each belt which is under tension
b.
More than 6 mm should be the correct a deflection for each belt which is under tension
c.
More than 8 mm should be the correct a deflection for each belt which is under tension.
d.
More than 6 mm and less than 8 mm should be the correct a deflection for each belt which is under tension.
Chapter 13 Solutions
AUTMOTIVE TECH, TECH MANUAL & MIND TAP
Ch. 13 - True or False? Make sure you locate and adhere to...Ch. 13 - How does a torque-to-yield bolt differ from...Ch. 13 - How do seals differ from gaskets?Ch. 13 - Where are thread sealers most often used?Ch. 13 - What are the major differences between aerobic and...Ch. 13 - Which of the following statements is incorrect?...Ch. 13 - True or False? Valve lash is adjusted in many...Ch. 13 - Which of the following statements about the...Ch. 13 - True or False? The computer in most late-model...Ch. 13 - Graphite is. an anaerobic substance an RTV an...
Ch. 13 - Which of the following are considered soft, cut...Ch. 13 - What material is typically not used to form a rear...Ch. 13 - Which of the following statements about preparing...Ch. 13 - On hybrid vehicles, how can you identify the high...Ch. 13 - True or False? Some crankshaft and camshaft timing...Ch. 13 - Prob. 1ASRQCh. 13 - Technician A uses adhesives to hold gaskets in...Ch. 13 - Technician A uses soft gaskets on valve covers....Ch. 13 - Technician A inspects all sealing surfaces for...Ch. 13 - Technician A says that oil pan gaskets are often...Ch. 13 - Prob. 6ASRQCh. 13 - While discussing proper engine break-in:...Ch. 13 - Prob. 8ASRQCh. 13 - Prob. 9ASRQCh. 13 - While selecting the proper RTV for a particular...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following is the most likely cause for a shudder during the engagement of a lock-up torque converter? a. A bad converter b. Worn or damaged CV or U-joints c. A worn front planetary gearset d. Loose flexplatearrow_forwardWhile discussing proper band adjustment procedures: Technician A says that on some vehicles the bands can be adjusted externally with a torque wrench. Technician B says that a calibrated inch- pound torque wrench is normally used to tighten the band adjusting bolt to a specified torque. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhile installing a timing belt: Technician A installs the belt, turns the crankshaft two full rotations, then applies tension to the belt. Technician B installs the belt, applies tension, then turns the crankshaft two full rotations. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
- True or False? Make sure you locate and adhere to the wet torque specs when tightening a bolt that has been lubricated with oil or any other liquid.arrow_forwardTechnician A says a bolt may become fatigued if it is over tightened. Technician B says that a bolt may become fatigued if it is under tightened. Who is correct?arrow_forwardwhat is the minnimum proof strength mpa for M14x2 hex boltarrow_forward
- Technician A uses a micrometer to measure the connecting rod journal for taper. Technician B uses a micrometer to measure the connecting rod journal for out-of-roundness. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardHow does a torque-to-yield bolt differ from standard bolts?arrow_forwardWhile inspecting the timing gears of an engine: Technician A says a gear with cracks, spalling, or excessive wear on the tooth surface indicates improper gear backlash. Technician B says the diameter of many of the engines timing gears and sprockets should be measured with the drive chain wrapped around the individual gears. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- The CV joint boots on the left side of a vehicle appear to be squeezed together; the boots on the right side of the vehicle appear to be stretched apart. Technician A says that one or more of the engine/transaxle's mounts may be broken. Technician B says that one or more of the engine/transaxle's subframe mounts may be broken. Who is correct? O a. A only O b.B only C. Both A and B O d. Neither A nor Barrow_forwardA vehicle makes a loud clicking sound during a left turn; during a right turn, the clicking noise is still apparent but is less pronounced. Technician A says that the left inner CV joint may be the source of the noise. Technician B says that the left outer CV joint may be causing the noise. Who is correct? O a. A only Ob.B only O c. Both A and B O d. Neither A nor Barrow_forwardTechnician A says that the transmission rear seal at the driveline is particularly prone to leakage. When Technician B pushes up and down on the transmission, he says that the mounts require replacement because the case moves up and down. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,