Physics for Scientists and Engineers, Technology Update, Hybrid Edition (with Enhanced WebAssign Multi-Term LOE Printed Access Card for Physics)
9th Edition
ISBN: 9781305116429
Author: Raymond A. Serway, John W. Jewett
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 14, Problem 14.77AP
To determine
The pressure required for the brake fluid in the cylinder.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
A uniform disk of mass 10.0 kg and radius 0.250 m spins at 300 rev/min on a low-friction axle. It must be brought to a stop in 1.00 min by a brake pad that makes contact with the disk at an average distance 0.220 m from the axis.The coefficient of friction between pad and disk is 0.500. A piston in a cylinder of diameter 5.00 cm presses the brake pad against the disk. Find the pressure required for the brake fluid in the cylinder.
Suppose you spray your sister with water from a garden hose. The water is supplied to the hose at a rate of 0.497×10−3 m3/s and the diameter of the nozzle you hold is 5.41×10−3 m. At what speed v does the water exit the nozzle?
In the calculation of pressures in fire hoses, it is often necessary to take into account the frictional losses suffered by the water as it flows along the hose. Consider a horizontal hose of diameter equal to 3.81 cm and length equal to 30 m carrying 394 liters/min of water. According to the tables used by firefighters, a pressure of 6.1 atm at the upstream end of this hose will result in a pressure of only 2.72 atm at the downstream end; the loss of 3.38 atm is attributed to friction. At what rate in does friction remove energy from the water?
Chapter 14 Solutions
Physics for Scientists and Engineers, Technology Update, Hybrid Edition (with Enhanced WebAssign Multi-Term LOE Printed Access Card for Physics)
Ch. 14 - Suppose you are standing directly behind someone...Ch. 14 - The pressure at the bottom of a filled glass of...Ch. 14 - Several common barometers are built, with a...Ch. 14 - You are shipwrecked and floating in the middle of...Ch. 14 - You observe two helium balloons floating next to...Ch. 14 - Figure OQ14.1 shows aerial views from directly...Ch. 14 - Prob. 14.2OQCh. 14 - A wooden block floats in water, and a steel object...Ch. 14 - An apple is held completely submerged just below...Ch. 14 - A beach ball is made of thin plastic. It has been...
Ch. 14 - A solid iron sphere and a solid lead sphere of the...Ch. 14 - Prob. 14.7OQCh. 14 - One of the predicted problems due to global...Ch. 14 - A boat develops a leak and, after its passengers...Ch. 14 - A small piece of steel is tied to a block of wood....Ch. 14 - A piece of unpainted porous wood barely floats in...Ch. 14 - A person in a boat floating in a small pond throws...Ch. 14 - Rank the buoyant forces exerted on the following...Ch. 14 - A water supply maintains a constant rate of flow...Ch. 14 - A glass of water contains floating ice cubes. When...Ch. 14 - An ideal fluid flows through a horizontal pipe...Ch. 14 - When an object is immersed in a liquid at rest,...Ch. 14 - Two thin-walled drinking glasses having equal base...Ch. 14 - Because atmospheric pressure is about 105 N/m2 and...Ch. 14 - A fish rests on the bottom of a bucket of water...Ch. 14 - You are a passenger on a spacecraft. For your...Ch. 14 - Prob. 14.6CQCh. 14 - Prob. 14.7CQCh. 14 - If you release a ball while inside a freely...Ch. 14 - (a) Is the buoyant force a conservative force? (b)...Ch. 14 - All empty metal soap dish barely floats in water....Ch. 14 - Prob. 14.11CQCh. 14 - Prob. 14.12CQCh. 14 - Prob. 14.13CQCh. 14 - Does a ship float higher in the water of an inland...Ch. 14 - Prob. 14.15CQCh. 14 - Prob. 14.16CQCh. 14 - Prairie dogs ventilate their burrows by building a...Ch. 14 - Prob. 14.18CQCh. 14 - Prob. 14.19CQCh. 14 - A large man sits on a four-legged chair with his...Ch. 14 - Prob. 14.2PCh. 14 - A 50.0-kg woman wearing high-heeled shoes is...Ch. 14 - Estimate the total mass of the Earths atmosphere....Ch. 14 - Calculate the mass of a solid gold rectangular bar...Ch. 14 - (a) A wry powerful vacuum cleaner has a hose 2.86...Ch. 14 - The spring of the pressure gauge shown in Figure...Ch. 14 - The small piston of a hydraulic lift (Fig. P14.8)...Ch. 14 - What must be the contact area between a suction...Ch. 14 - A swimming pool has dimensions 30.0 m 10.0 m and...Ch. 14 - (a) Calculate the absolute pressure at the bottom...Ch. 14 - Prob. 14.12PCh. 14 - Prob. 14.13PCh. 14 - A container is filled to a depth of 20.0 cm with...Ch. 14 - Review. The lank in Figure P14.15 is filled with...Ch. 14 - Prob. 14.16PCh. 14 - Prob. 14.17PCh. 14 - Review. A solid sphere of brass (bulk modulus of...Ch. 14 - Normal atmospheric pressure is 1.013 103 Pa. The...Ch. 14 - The human brain and spinal cord are immersed in...Ch. 14 - Blaise Pascal duplicated Torricellis barometer...Ch. 14 - Prob. 14.22PCh. 14 - A backyard swimming pool with a circular base of...Ch. 14 - A tank with a flat bottom of area A and vertical...Ch. 14 - A table-tennis ball has a diameter of 3.80 cm and...Ch. 14 - Prob. 14.26PCh. 14 - A 10.0-kg block of metal measuring 12.0 cm by 10.0...Ch. 14 - A light balloon is filled with 400 m3 of helium at...Ch. 14 - A cube of wood having an edge dimension of 20.0 cm...Ch. 14 - The United States possesses the ten largest...Ch. 14 - A plastic sphere floats in water with 50.0% of its...Ch. 14 - A spherical vessel used for deep-sea exploration...Ch. 14 - A wooden block of volume 5.24 104 m3 floats in...Ch. 14 - The weight of a rectangular block of low-density...Ch. 14 - A large weather balloon whose mass is 226 kg is...Ch. 14 - A hydrometer is an instrument used to determine...Ch. 14 - Refer to Problem 16 and Figure P14.16. A...Ch. 14 - On October 21, 2001, Ian Ashpole of the United...Ch. 14 - How many cubic meters of helium are required to...Ch. 14 - Water flowing through a garden hose of diameter...Ch. 14 - A large storage tank, open at the top and filled...Ch. 14 - Prob. 14.42PCh. 14 - Prob. 14.43PCh. 14 - A village maintains a large tank with ail open...Ch. 14 - A legendary Dutch boy saved Holland by plugging a...Ch. 14 - Water falls over a dam of height h with a mass...Ch. 14 - Water is pumped up from the Colorado River to...Ch. 14 - In ideal flow, a liquid of density 850 kg/m3 moves...Ch. 14 - The Venturi tube discussed in Example 14.8 and...Ch. 14 - Review. Old Faithful Geyser in Yellowstone...Ch. 14 - An airplane is cruising al altitude 10 km. The...Ch. 14 - An airplane has a mass of 1.60 104 kg, and each...Ch. 14 - Prob. 14.53PCh. 14 - The Bernoulli effect can have important...Ch. 14 - Prob. 14.55PCh. 14 - Decades ago, it was thought that huge herbivorous...Ch. 14 - (a) Calculate the absolute pressure at an ocean...Ch. 14 - Prob. 14.58APCh. 14 - A spherical aluminum ball of mass 1.26 kg contains...Ch. 14 - Prob. 14.60APCh. 14 - Review. Figure P14.61 shows a valve separating a...Ch. 14 - The true weight of an object can be measured in a...Ch. 14 - Water is forced out of a fire extinguisher by air...Ch. 14 - Review. Assume a certain liquid, with density 1...Ch. 14 - Prob. 14.65APCh. 14 - Prob. 14.66APCh. 14 - Prob. 14.67APCh. 14 - A common parameter that can be used to predict...Ch. 14 - Evangelista Torricelli was the first person to...Ch. 14 - Review. With reference to the dam studied in...Ch. 14 - A 1.00-kg beaker containing 2.00 kg of oil...Ch. 14 - A beaker of mass mb containing oil of mass mu and...Ch. 14 - In 1983, the United States began coining the...Ch. 14 - Review. A long, cylindrical rod of radius r is...Ch. 14 - Prob. 14.75APCh. 14 - The spirit-in-glass thermometer, invented in...Ch. 14 - Prob. 14.77APCh. 14 - Review. In a water pistol, a piston drives water...Ch. 14 - Prob. 14.79APCh. 14 - The water supply of a building is fed through a...Ch. 14 - A U-tube open at both ends is partially filled...Ch. 14 - A woman is draining her fish tank by siphoning the...Ch. 14 - The hull of an experimental boat is to be lifted...Ch. 14 - Prob. 14.84APCh. 14 - An ice cube whose edges measure 20.0 mm is...Ch. 14 - Why is the following situation impossible? A barge...Ch. 14 - Show that the variation of atmospheric pressure...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- A manometer containing water with one end connected to a container of gas has a column height difference of 0.60 m (Fig. P15.72). If the atmospheric pressure on the right column is 1.01 105 Pa, find the absolute pressure of the gas in the container. The density of water is 1.0 103 kg/m3. FIGURE P15.72arrow_forwardReview. In a water pistol, a piston drives water through a large tube of area A1 into a smaller tube of area A2 as shown in Figure P14.46. The radius of the large tube is 1.00 cm and that of the small tube is 1.00 mm. The smaller tube is 3.00 cm above the larger tube. (a) If the pistol is fired horizontally at a height of 1.50 m, determine the time interval required for the water to travel from the nozzle to the ground. Neglect air resistance and assume atmospheric pressure is 1.00 atm. (b) If the desired range of the stream is 8.00 m, with what speed v2 must the stream leave the nozzle? (c) At what speed v1 must the plunger be moved to achieve the desired range? (d) What is the pressure at the nozzle? (e) Find the pressure needed in the larger tube. (f) Calculate the force that must be exerted on the trigger to achieve the desired range. (The force that must be exerted is due to pressure over and above atmospheric pressure.) Figure P14.46arrow_forwardA vertical cylinder of cross-sectional area A is fitted with a tight-fitting, frictionless piston of mass m (Fig. P18.40). The piston is not restricted in its motion in any way and is supported by the gas at pressure P below it. Atmospheric pressure is P0. We wish to find the height h in Figure P18.40. (a) What analysis model is appropriate to describe the piston? (b) Write an appropriate force equation for the piston from this analysis model in terms of P, P0, m, A, and g. (c) Suppose n moles of an ideal gas are in the cylinder at a temperature of T. Substitute for P in your answer to part (b) to find the height h of the piston above the bottom of the cylinder. Figure P18.40arrow_forward
- In a water pistol, a piston drives water through a larger tube of radius 1.00 cm into a smaller tube of radius 1.00 mm as in Figure P9.41. (a) If the pistol is fired horizontally at a height of 1.50 m, use ballistics to determine the time it takes water to travel from the nozzle to the ground. (Neglect air resistance and assume atmospheric pressure is 1.00 atm.) (b) If the range of the stream is to be 8.00 m, with what speed must the stream leave the nozzle? (c) Given the areas of the nozzle and cylinder, use the equation of continuity to calculate the speed at which the plunger must be moved.(d) What is the pressure at the nozzle? (e) Use Bernoulli’s equation to find the pressure needed in the larger cylinder. Can gravity terms be neglected? (f ) Calculate the force that must be exerted on the trigger to achieve the desired range. (The force that must be exerted is due to pressure over and above atmospheric pressure.)arrow_forwardDuring a high Reynolds number experiment, the total drag force acting on a spherical body of diameter D = 12 cm subjected to airflow at 1 atm and 5°C is measured to be 5.2 N. The pressure drag acting on the body is calculated by integrating the pressure distribution (measured by the use of pressure sensors throughout the surface) to be 4.9 N. Determine the friction drag coefficient of the sphere.arrow_forwardA sump pump (used to drain water from the basement of houses built below the water table) is draining a flooded basement at the rate of 0.85 L/s, with an output pressure of 3.05 × 105 Pa. a. The water enters a hose with a 2.8 cm inside diameter and rises 2.4 m above the pump. What is its pressure at this point, in pascals? You may neglect frictional losses. b. The hose then goes over the foundation wall, losing 0.35 m in height, and widens to 4.4 cm in diameter. What is the pressure now, in pascals? You may neglect frictional losses.arrow_forward
- Consider a symmetrical U-shaped tube, of circular section and internal diameter d<<R, containing an incompressible liquid of density ρ. Before starting the rotation of the system, the system is in equilibrium, where the rotating branch has an initial height of fluid equal to L, while at the other end of the tube there is a chamber of height h and filled with a gas at initial pressure P0. The top cap of the chamber is attached to the tube. However, the bottom cap can be moved vertically acting as a “piston”, as shown in the diagram. Both the mass of the lower lid and that of the gas contained in the chamber are negligible.Suddenly the tube begins to rotate at constant angular velocity ω. About: For the initial instant find a relationship between the pressure P0 of the gas, the height h, the properties fluid physics and Patm.arrow_forwardA sump pump (used to drain water from the basement of houses built below the water table) is draining a flooded basement at the rate of 0.75 L/s, with an output pressure of 2.9 × 105 Pa. a) The water enters a hose with a 3.4 cm inside diameter and rises 2.5 m above the pump. What is its pressure at this point, in pascals? You may neglect frictional losses. b)The hose then goes over the foundation wall, losing 0.55 m in height, and widens to 4.1 cm in diameter. What is the pressure now, in pascals? You may neglect frictional losses.arrow_forwardA sump pump (used to drain water from the basement of houses built below the water table) is draining a flooded basement at the rate of 0.75 L/s, with an output pressure of 2.9 × 105 Pa. a)The water enters a hose with a 3.4 cm inside diameter and rises 2.5 m above the pump. What is its pressure at this point, in pascals? You may neglect frictional losses. b) The hose then goes over the foundation wall, losing 0.55 m in height, and widens to 4.1 cm in diameter. What is the pressure now, in pascals? You may neglect frictional losses.arrow_forward
- The crank and connecting rod of a theoretical steam engine are 0.4 m and 1.6 m long, respectively. The crank makes 180 rpm in clockwise direction. When it has turned 45° from the inner dead center position, determine the: a) Velocity of piston, b) Angular velocity of connecting rodarrow_forwardA cylindrical drum of radius 0.5 m is used to hold 400 liters of petroleum ether (density = .68 g/mL or 680 kg/m3 ). (Note: 1 liter = 0.001 m3 ) a. Determine the amount of pressure applied to the walls of the drum if the petroleum ether fills the drum to its top. b. Determine the amount of pressure applied to the floor of the drum if the petroleum ether fills the drum to its top. c. If the drum were redesigned to hold 800 liters of petroleum ether: i. How would the pressure on the walls change? Would it increase, decrease, or stay the same? ii. How would the pressure on the floor change? Would it increase, decrease, or stay the same?arrow_forwardLuigi is attempting to fix some Mushroom Kingdom plumbing. At one point in the plumbing, a horizontal pipe is carrying an incompressible frictionless fluid of density 1.31*10^ 3 kg/m^ 3 . The pipe widens from d_{1} = 2.59 cm at left to d_{2} = 6.61 cm at right , as shown below. If the fluid enters the narrower left end of the pipe at a speed of 2.33 m/s , by how much must the pressure drop or rise (in Pa) at the wider right end of the pipe? Be sure to include the appropriate sign! Explain how you solved the problem involving a fluid passing through a pipe. Be sure to state what your known and unknown quantities are, what concepts were applied , and what equations were used!arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
- Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and Engineers
Physics
ISBN:9781337553278
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...
Physics
ISBN:9781337553292
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning