Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
5th Edition
ISBN: 9780133994612
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 14, Problem 6RQ
What math function is needed to calculate the overall gear ratio if the transmission and differential ratios are both known?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Determine gear ratio and transfer function
5(a) Why mechanical actuation is important in mechatronics system? Classify various types of gears. Define gear ratio. Give some illustrations of calculating gear ratio. Why belt and chain drives are utilised in industrial process? Mention various types of belts.
what factors determine the design of the power transmission mechanisms in a rear wheel drive van (Diesel) and how do you calculate power and torque at the driveshaft, assuming the following: its 5 speed transmission, Gear system efficiency is 88% Gear ratios: 1 st: 4.17:1
2 nd 2.34:1
3 rd 1.52:1
4 th 1.14:1
and power and torque to be calculated at the point where engine is generating its maximum power
Chapter 14 Solutions
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Ch. 14 - What is the formula for determining fuel economy?Ch. 14 - Why are the torque and horsepower of an engine...Ch. 14 - What service operation may require the technician...Ch. 14 - What service operation may require the technician...Ch. 14 - Prob. 5RQCh. 14 - What math function is needed to calculate the...Ch. 14 - Prob. 1CQCh. 14 - Which of the following shows the relationship of...Ch. 14 - Prob. 3CQCh. 14 - Prob. 4CQ
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Repeat Problem 4-6 except solve by the vector loop method.
DESIGN OF MACHINERY
Determine the velocity of block D if end A of the rope is pulled down with a speed of vA = 3 m/s.
Engineering Mechanics: Dynamics (14th Edition)
A windowmounted air conditioner removes 3.5kJ from the inside of a home using 1.75 kJ work input. How much ener...
EBK FUNDAMENTALS OF THERMODYNAMICS, ENH
What types of polymers are most commonly blow molded?
DeGarmo's Materials and Processes in Manufacturing
Steady state conduction rate to the warm compressor to the net power produces theoretically by thermodynamic ba...
Introduction to Heat Transfer
Convert the following quantities from English to SI units: a. 98 Btu/(hr-ft-F) b. 0.24 Btu/(lbm-F) C. 0.04 Ibm/...
Heating Ventilating and Air Conditioning: Analysis and Design
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- How are Gear ratio and Speed ratio related? Are they equal to each other?arrow_forwardWhat is the extreme transmission angle values by using maxima and minima condition, of the transmission angle occur when the crank is perpendicular to the slider path in a slider-crank linkage.arrow_forwardTechnician A says that if a single idler gear is used to obtain reverse gear, its size and number of teeth must be used to calculate gear ratios. Technician B says that an idler gear is often used for reverse gear because it causes the output shaft to rotate in the reverse direction of the input shaft. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- When a transmission is described as having two planetary gearsets in tandem, what does this mean?arrow_forwardWhy do you think a 5-speed manual Ford Mustang is geared as followed? Gear 1, 3.35:1 Ratio Gear 2, 1.93:1 Ratio Gear 3, 1.29:1 Ratio Gear 4, 1.00:1 Ratio Gear 5, 0.68:1 Ratio (Overdrive)arrow_forwardfirst and last gear having teeth 30 and 5C respectively of a simple gear train. What will be the train value and speed ratiorespectively if first gear is driving geararrow_forward
- When discussing the various gear positions of a transfer case, Technician A says that when the transfer case is in low, the overall gear ratio is numerically increased. Technician B says that when the transfer case is in the high position, the vehicle operates in an overdrive mode due to the decrease in torque multiplication. Who is correct?arrow_forwardThere is a motor with a power of 38 HP. The driving pinion has a speed of 20 rpm and the driven pinion of 5 rpm. Design the driving pinion and driven pinion based on the rpm of each pinion. do not forget the module and the number of teeth for each pinion. Gear ratio value: i= 5 rpm / 20 rpm = 0.25arrow_forwardDiscuss the main advantages and disadvantages of at least 2 drive systems that can be used to drive a camshaft ?arrow_forward
- Q#2: For the two-gear system shown in following figure; a) Calculate Gear Ratio b) If the speed of Driver Gear is 30 revolutions per minute (rpm) then what will be speed of Driven Gear? c) Among two gears (driven gear and driver gear), which gear has highest speed in revolutions per minute.? d) What should be number of teeth on Driven gear to move with speed of 4 times than that of Driver Gear?arrow_forwardYou have engaged in open discussion in which you have to evaluate the conditions needed for anepicyclic gear train to become a differential. Using appropriate schematic and hand sketch show how adifferential works in this applicationarrow_forwardwhat pushes the baulk ring onto the come on the gear when the sleeve starts to move on the hub? how does the baulk ring block the sleeve from engaing with the dog teeth on the gear before synchronization occurs? when would a noisy input shaft bearing be more noticeable? what is the difference between a fulltime and part-time four wheel (4WD) system?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License