Vector Mechanics for Engineers: Statics and Dynamics
12th Edition
ISBN: 9781259638091
Author: Ferdinand P. Beer, E. Russell Johnston Jr., David Mazurek, Phillip J. Cornwell, Brian Self
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 14.1, Problem 14.9P
A 20-kg base satellite deploys three sub-satellites, each of which has its own thrust capabilities, to perform research on tether propulsion. The masses of sub-satellites A, B, and C are 4 kg, 6 kg, and 8 kg, respectively, and their velocities expressed in m/s are given by vA = 4i − 2j + 2k, vB = i + 4j, vC = 2i + 2j + 4k. At the instant shown, what is the angular momentum HO of the system about the base satellite?
Fig. P14.9 and P14.10
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The 18 000-kg F-35B uses thrust vectoring to allow it to take off vertically. In one maneuver, the pilot reaches the top of her static hover at 200 m. The combined thrust and lift force on the airplane applied at the end of the static hover can be expressed as F = (44t + 2500t2)i + (250t2 + t + 176 580)j, where F and t are expressed in newtons and seconds, respectively. Determine how long it will take the airplane to reach a cruising speed of 1000 km/hr (cruising speed is defined to be in the x-direction only).
Principle of Angular Impulse and Momentum
To apply the principle of angular impulse and momentum to find final speed and the time to reach a given speed.
As shown, ball B, having a mass of 10.0 kg, is attached to the end of a rod whose mass can be neglected.
Finding the final speed of the ball If the rod is 0.550 m long and subjected to a torque M=(1.95t2+3.75) N⋅m, where t is in seconds, determine the speed of the ball when t=4.80 s. The ball has a speed of v=2.25 m/s when t=0
Finding the time needed to reach a specific speed
If the shaft is 0.250 m long, the ball has a speed of v=2.85 m/s when t=0, and the rod is subjected to a torque M=(3.40t+2.15) N⋅m, where t is in seconds, determine the time it will take for the ball to reach a speed of 5.80 m/s.
A 540-kg spacecraft is mounted on top of a rocket with a mass of 19 Mg, including 17.8 Mg of fuel. Knowing that the fuel is consumed at a rate of 225 kg/s and ejected with a relative velocity of 3600 m/s, determine the maximum speed imparted to the spacecraft if the rocket is fired vertically from the ground.
Chapter 14 Solutions
Vector Mechanics for Engineers: Statics and Dynamics
Ch. 14.1 - A 30-g bullet is fired with a horizontal velocity...Ch. 14.1 - Two identical 1350-kg automobiles A and B are at...Ch. 14.1 - An airline employee tosses two suitcases in rapid...Ch. 14.1 - Car A weighing 4000 lb and car B weighing 3700 lb...Ch. 14.1 - Two swimmers A and B, of weight 190 lb and 125 lb,...Ch. 14.1 - A 180-lb man and a 120-lb woman stand side by side...Ch. 14.1 - A 40-Mg boxcar A is moving in a railroad...Ch. 14.1 - Two identical cars A and B are at rest on a...Ch. 14.1 - A 20-kg base satellite deploys three...Ch. 14.1 - For the satellite system of Prob. 14.9, assuming...
Ch. 14.1 - A system consists of three identical 19.32-lb...Ch. 14.1 - A system consists of three identical 19.32-lb...Ch. 14.1 - A system consists of three particles A, B, and C....Ch. 14.1 - For the system of particles of Prob. 14.13,...Ch. 14.1 - A 13-kg projectile is passing through the origin O...Ch. 14.1 - Prob. 14.16PCh. 14.1 - A 2-kg model rocket is launched vertically and...Ch. 14.1 - An 18-kg cannonball and a 12-kg cannonball are...Ch. 14.1 - 14.19 and 14.20 Cruiser A was traveling east at 60...Ch. 14.1 - 14.19 and 14.20 Cruiser A was traveling east at 60...Ch. 14.1 - Prob. 14.21PCh. 14.1 - Two spheres, each of mass m, can slide freely on a...Ch. 14.1 - In a game of pool, ball A is moving with a...Ch. 14.1 - Prob. 14.24PCh. 14.1 - Prob. 14.25PCh. 14.1 - In a scattering experiment, an alpha particle A is...Ch. 14.1 - Derive the relation HO=rmv+HG between the angular...Ch. 14.1 - Prob. 14.28PCh. 14.1 - Prob. 14.29PCh. 14.1 - Show that the relation MA=HA, where HA is defined...Ch. 14.2 - Determine the energy lost due to friction and the...Ch. 14.2 - In Prob. 14.3, determine the energy lost (a) when...Ch. 14.2 - Prob. 14.33PCh. 14.2 - Determine the energy lost as a result of the...Ch. 14.2 - Prob. 14.35PCh. 14.2 - Prob. 14.36PCh. 14.2 - Prob. 14.37PCh. 14.2 - Ball B is suspended from a cord of length l...Ch. 14.2 - A 15-lb block B starts from rest and slides on the...Ch. 14.2 - A 40-lb block B is suspended from a 6-ft cord...Ch. 14.2 - Prob. 14.41PCh. 14.2 - 14.41 and 14.42 In a game of pool, ball A is...Ch. 14.2 - Prob. 14.43PCh. 14.2 - In a game of pool, ball A is moving with the...Ch. 14.2 - Prob. 14.45PCh. 14.2 - Prob. 14.46PCh. 14.2 - Four small disks A, B, C, and D can slide freely...Ch. 14.2 - In the scattering experiment of Prob. 14.26, it is...Ch. 14.2 - Three identical small spheres, each weighing 2 lb,...Ch. 14.2 - Three small spheres A, B, and C, each of mass m,...Ch. 14.2 - Prob. 14.51PCh. 14.2 - Prob. 14.52PCh. 14.2 - Two small disks A and B of mass 3 kg and 1.5 kg,...Ch. 14.2 - Two small disks A and B of mass 2 kg and 1 kg,...Ch. 14.2 - Three small identical spheres A, B, and C, which...Ch. 14.2 - Prob. 14.56PCh. 14.3 - A stream of water with a density of = 1000 kg/m3...Ch. 14.3 - A jet ski is placed in a channel and is tethered...Ch. 14.3 - Tree limbs and branches are being fed at A at the...Ch. 14.3 - Prob. 14.60PCh. 14.3 - Prob. 14.61PCh. 14.3 - Prob. 14.62PCh. 14.3 - Prob. 14.63PCh. 14.3 - Prob. 14.64PCh. 14.3 - Prob. 14.65PCh. 14.3 - Prob. 14.66PCh. 14.3 - Prob. 14.67PCh. 14.3 - Prob. 14.68PCh. 14.3 - Prob. 14.69PCh. 14.3 - Prob. 14.70PCh. 14.3 - Prob. 14.71PCh. 14.3 - Prob. 14.72PCh. 14.3 - Prob. 14.73PCh. 14.3 - Prob. 14.74PCh. 14.3 - Prob. 14.75PCh. 14.3 - Prob. 14.76PCh. 14.3 - The propeller of a small airplane has a...Ch. 14.3 - Prob. 14.78PCh. 14.3 - Prob. 14.79PCh. 14.3 - Prob. 14.80PCh. 14.3 - Prob. 14.81PCh. 14.3 - Prob. 14.82PCh. 14.3 - Prob. 14.83PCh. 14.3 - Prob. 14.84PCh. 14.3 - Prob. 14.85PCh. 14.3 - Prob. 14.86PCh. 14.3 - Solve Prob. 14.86, assuming that the chain is...Ch. 14.3 - Prob. 14.88PCh. 14.3 - Prob. 14.89PCh. 14.3 - Prob. 14.90PCh. 14.3 - Prob. 14.91PCh. 14.3 - Prob. 14.92PCh. 14.3 - A rocket sled burns fuel at the constant rate of...Ch. 14.3 - Prob. 14.94PCh. 14.3 - Prob. 14.95PCh. 14.3 - Prob. 14.96PCh. 14.3 - Prob. 14.97PCh. 14.3 - Prob. 14.98PCh. 14.3 - Determine the distance traveled by the spacecraft...Ch. 14.3 - A rocket weighs 2600 lb, including 2200 lb of...Ch. 14.3 - Determine the altitude reached by the spacecraft...Ch. 14.3 - Prob. 14.102PCh. 14.3 - Prob. 14.103PCh. 14.3 - Prob. 14.104PCh. 14 - Three identical cars are being unloaded from an...Ch. 14 - A 50-kg mother and her 26-kg son are sledding down...Ch. 14 - An 80-Mg railroad engine A coasting at 6.5 km/h...Ch. 14 - Prob. 14.108RPCh. 14 - Mass C, which has a mass of 4 kg, is suspended...Ch. 14 - Prob. 14.110RPCh. 14 - A 6000-kg dump truck has a 1500-kg stone block...Ch. 14 - For the ceiling-mounted fan shown, determine the...Ch. 14 - Prob. 14.113RPCh. 14 - Prob. 14.114RPCh. 14 - Prob. 14.115RPCh. 14 - A chain of length l and mass m falls through a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A system consists of three particles A, B, and C. We know that mA =3kg, mB =2kg, and mC = 4 kg and that the velocities of the particles expressed in m/s are, respectively, vA = 4i +2j +2k, vB = 4i + 3j, and vC = -2i + 4j +2k. Determine the angular momentum HO of the system about O.arrow_forwardat an amusement park there are 200 kg bumper cars A, B, and C that have riders with masses of 40kg, 60 kg, and 35 kg, respectively. Car A is moving to the right with a velocity Va=2m/s when it hits stationary car B. The coefficient of restitution between each car is 0.8. Determine the velocity of car C so that after car B collides with car C the velocity of car B is zero.arrow_forwardA 1-lb stone is dropped down the “bottomless pit” at Carlsbad Caverns and strikes the ground with a speed of 108 ft/s. Neglecting air resistance, determine the kinetic energy of the stone as it strikes the ground and the height h from which it was dropped. The kinetic energy of the stone is ____ft·lb. The height from which the stone was dropped is ___ft.arrow_forward
- A block of mass 0.25 kg travels down a frictionless surface with a velocity of 4.5 m/s to the left and collides with a second block of mass 1.5 kg with a velocity of 0.5 m/s to the right. The two carts stick together after the collision. (1) Find the total momentum of the two carts just before the collision. (2) Find the velocity of the two carts just after the collision.arrow_forwardAn airline employee tosses two suitcases with weights of 30 lb and 40 lb, respectively, onto a 50-lb baggage carrier in rapid succession. Knowing that the carrier is initially at rest and that the employee imparts a 9-ft/s horizontal velocity to the 30-lb suitcase and a 6-ft/s horizontal velocity to the 40-lb suitcase, determine the final velocity of the baggage carrier if the first suitcase tossed onto the carrier is (a) the 30-lb suitcase, (b) the 40-lb suitcase.arrow_forwardTo find the maximum velocity of two dump trucks connected by a cable. As shown, two dump trucks are connected by a cable. One truck (Truck 1) is loaded, has a maximum engine power P , and is able to attain a maximum speed of v. Another truck (Truck 2) has a maximum engine power 2P and can attain a maximum speed of 1.5v. To solve this problem, assume that each truck, when not attached to the other truck, has a speed that is limited only by wind resistance. Also assume the following: The wind resistance is a constant force (although a different constant for each truck). Therefore, it is independent of a truck’s speed. The wind resistance force on each truck is the same before and after the cable is connected. The power that a truck's engine can generate is independent of that truck's speed. Find vmax, the maximum speed of the two trucks when they are connected. Assume that both engines are running at maximum power. Express your answer in terms of v.arrow_forward
- A pile-driver of mass 500 kg falls freely through a height of 1.5 m on to a pile of mass 200 kg. Determine the velocity with which the driver hits the pile. If, at impact, 3 kJ of energy are lost due to heat and sound, the remaining energy being possessed by the pile and driver as they are driven together into the ground a distance of 200 mm, determine (a) the common velocity immediately after impact, (b) the average resistance of the ground.arrow_forwardA 180-lb man and a 120-lb woman stand side by side at both ends of the 300-lb boat, ready to dive, each with a 16-ft/s speed relative to the boat. Determine the speed of the boat after they both dive, if (a) the woman dives first, (b) the man dives first. (show your solution) choices of correct answer: 3.0723 km/hr ; 0.251 km/hr 13.0723 km/hr ;1.251 km/hr 10.095 km/hr; 10.2815 km/hr 18.0723 km/hr; 0.521 km/hr 0.251 km/hr; 8.0723 km/hrarrow_forward(b) A package drops from a chute into a cart with a velocity of V m/s as shown in Figure Q5(b). Knowing that the cart is initially at rest and can roll freely, determine the final velocity of the cart and the impulse exerted by the cart on the package. The mass of package, Wp and cart, Wc with velocity are given Wp = 18 kg Wc= 35kg V= 7 m/sarrow_forward
- A 5.00 kg block is released from rest on a ramp that is inclined at an angle of 60.0° below the horizontal. The initial position of the block is a vertical distance of 2.00 m above the bottom of the ramp. (a) If the speed of the block is 5.00 m/s when it reaches the bottom of the ramp, what was the work done on it by the friction force? (b) If the angle of the ramp is changed but the block is released from a point that is still 2.00 m above the base of the ramp, both the magnitude of the friction force and the distance along the ramp that the block travels change. If the angle of the incline is changed to 50.0°, does the magnitude of the work done by the friction force increase or decrease compared to the value calculated in part (a)? (c) How much work is done by friction when the ramp angle is 50.0°?arrow_forwardA 36.0-g projectile is launched by the expansion of hot gas in an arrangement shown in figure a. The cross-sectional area of the launch tube is 1.0 cm2, and the length that the projectile travels down the tube after starting from rest is 32 cm. As the gas expands, the pressure varies as shown in figure b. The values for the initial pressure and volume are Pi = 12 ✕ 105 Pa and Vi = 8.0 cm3 while the final values are Pf = 1.1 ✕ 105 Pa and Vf = 40.0 cm3. Friction between the projectile and the launch tube is negligible. (a) If the projectile is launched into a vacuum, what is the speed of the projectile as it leaves the launch tube? In m/s. (b) If instead the projectile is launched into air at a pressure of 1.1 ✕ 105 Pa, what fraction of the work done by the expanding gas in the tube is spent by the projectile pushing air out of the way as it proceeds down the tube? w(spent)/w(env)=arrow_forwardIf a ball is dropped from a height (H) its velocity will increase until it hits the ground (assuming that aerodynamic drag due to the air is negligible). During its fall, its initial potential energy is converted into kinetic energy. If the ball is dropped from a height of 680 centimeters [cm], and the impact velocity is 38 feet per second [ft/s], determine the value of gravity in units of meters per second squared [m/s2].arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Dynamics - Lesson 1: Introduction and Constant Acceleration Equations; Author: Jeff Hanson;https://www.youtube.com/watch?v=7aMiZ3b0Ieg;License: Standard YouTube License, CC-BY