(a)
The peak current in the inverter during the switching cycle.
(a)
Answer to Problem 16.37P
The value of the current in the transistor is
Explanation of Solution
Calculation:
The expression to determine the value of the
Substitute
The expression to determine the value of the
Substitute
The expression to determine the transition points
Substitute
The expression for the maximum value of the current through the NMOS transistor is given by,
Substitute
Substitute
Conclusion:
Therefore, the value of the current in the transistor is
(b)
The peak current in the inverter during the switching cycle.
(b)
Answer to Problem 16.37P
The maximum value of the current in the transistor is
Explanation of Solution
Calculation:
The expression to determine the value of the
Substitute
The expression to determine the value of the
Substitute
The expression to determine the transition points
Substitute
The expression for the maximum value of the current through the NMOS transistor is given by,
Substitute
Substitute
Conclusion:
Therefore, the maximum value of the current in the transistor is
(c)
The peak current in the inverter during the switching cycle.
(c)
Answer to Problem 16.37P
The maximum value of the current in the transistor is
Explanation of Solution
Calculation:
The expression to determine the value of the
Substitute
The expression to determine the value of the
Substitute
The expression to determine the transition points
Substitute
The expression for the maximum value of the current through the NMOS transistor is given by,
Substitute
Substitute
Conclusion:
Therefore, the maximum value of the current in the transistor is
Want to see more full solutions like this?
Chapter 16 Solutions
Microelectronics Circuit Analysis and Design
- If,for a single phase half bridge inverter the amplitude of output voltage is Vs and the output power is P then their corresponding values for a single phase full-bridge inverter are a. 2Vs,2P b. 2Vs,4P c. 2Vs,P d. Vs,Parrow_forwardDesign an NMOS depletion load inverter (VDD =3.3 V, VL = 0.20 V, VTNS = 0.75 V, VTNL = −2 V,γ = 0) to have an average propagation delay of 1 nswith a capacitive load of 0.2 pF. What is the averagestatic power dissipation of this gate?arrow_forwardRedesign the resistive load inverter for operation at a power level of 0.30 mW withVDD = 3.3 V. Assume VT O = 0.7 V. Keep theother design parameters the same. What is the newsize of MS and the value of R? (b) What are thevalues for NMH and NML ?arrow_forward
- If a 3 phase inverter is feeding an appliance that is rated as 207v AC, 60Hz, 100kVA, compute the minimum DC input voltage, that must be feed to the inverter. Assume the Modulation Index Ma to 1. ...arrow_forwardThe single-phase half-bridge inverter has a resistive load of R = 2.4Ω and the DCinput voltage is 48V. Determine:1- the rms output voltage at the fundamental frequency2- fundamental displacement factor .3- fundamental power , drown from each source .4- fundamental load power .5- total power drown from each source .6- total load power .arrow_forwardRedraw the circuit using a saturated load transistor. (b) What is the logic functionof the new circuit? (c) What are the W/L ratios ofthe transistors based on the reference inverter design in 6.24(b)?arrow_forward
- Plot the noise margins of the inverter asa function of W/L of the switching transistorarrow_forwardDraw the schematic for a four-input NAND gatewith a depletion-mode load device. What are theW/L ratios of all the transistors, based on the reference inverter ?arrow_forwardA two-stage inverter is shown in this figure. Vs=50 V. v=110V2 sin 100 nt. The average voltage of C is set to be 200 V.1=2 A. The bipolar modulation scheme is applied on the inverter and the power factor of the inverter is set to be 1. Consider the two-stage inverter is lossless, Calculate the current of L. il (ii) Assume the voltage of Cr is a constant DC voltage of 200 V. Calculate the instantaneous duty ratio of the inverter. din if C = 75 HF, calculate the highest and lowest voltage of Cr.arrow_forward
- A resistive load of 30Ω is connected to an IGBT based Single-Phase Half-Bridge Inverter.The DC source voltage Vs=120V. EVALUATE Fundamental component of load voltage and fundamental component of load current;arrow_forwardA resistive load of 30Ω is connected to an IGBT based Single-Phase Half-Bridge Inverter.The DC source voltage Vs=120V. EVALUATE THE Output voltage (rms value) and peak voltage across the device at OFF state;arrow_forwardA resistive load of 30Ω is connected to an IGBT based Single-Phase Half-Bridge Inverter.The DC source voltage Vs=120V. Sketch the waveforms of load voltage, fundamental component of load voltage, fundamental component of load current, current through any one device and voltage across any device .arrow_forward
- Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSONDelmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningProgrammable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
- Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill EducationElectric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSONEngineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,