Manufacturing Engineering & Technology
Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133128741
Author: Serope Kalpakjian, Steven Schmid
Publisher: Prentice Hall
bartleby

Concept explainers

Nanomaterials and Applications
Nanomaterials are materials that are composed of nanoparticles having a size ranging from 1 to 100 nm. The constituent particles are 100,000 times smaller than the thickness of a strand of human hair. The nanoparticles cannot be seen through naked eyes a…
Question
Book Icon
Chapter 17, Problem 37QTP
To determine

Assume that the surface of a copper particle is covered by an oxide layer 0.1 mm in thickness. What is the volume (and the percentage of volume) occupied bythis layer if the copper particle itself is 75 μm in diameter?

Expert Solution & Answer
Check Mark

Want to see the full answer?

Check out a sample textbook solution
Blurred answer
Previous
Chapter 17, Problem 36QTP
Next
Chapter 17, Problem 38QTP
Students have asked these similar questions
Describe the advantages and the limitations for this application: 1) Deposition of ceramic coatings with a very high melting point.
Give one example of a nanomaterial excluding Nano-Titanium Dioxide, Silver Nanoparticles and Graphene and identify its properties and applications.
A coating process using suspended particles in a liquid can attain formation of an ultrafiltration ceramic top-layer on a porous support (substrate). Which type of coating mechanisms is most probable? What is the effect of the coating time on the thickness of the coated layer? What is the effect of the pulling rate out of the liquid on the thickness of the coated layer?

Chapter 17 Solutions

Manufacturing Engineering & Technology

Ch. 17 - Describe briefly the production steps involved in...Ch. 17 - Name the various methods of powder production and...Ch. 17 - Explain why metal powders may be blended.Ch. 17 - Describe the methods used in metal powder...Ch. 17 - What is isostatic pressing? How is it different...Ch. 17 - What hazards are involved in PM processing?...Ch. 17 - Describe what occurs to metal powders during...Ch. 17 - Prob. 8RQCh. 17 - Why might secondary and finishing operations be...Ch. 17 - Prob. 10RQ
Ch. 17 - Prob. 11RQCh. 17 - Prob. 12RQCh. 17 - Prob. 13RQCh. 17 - What is screening of metal powders? Why is it...Ch. 17 - Why are protective atmospheres necessary in...Ch. 17 - Why is there density variation in the compacting...Ch. 17 - What is the magnitude of the stresses and forces...Ch. 17 - List the similarities and differences of forging...Ch. 17 - Give some reasons that powder-injection molding is...Ch. 17 - How does the equipment used for powder compaction...Ch. 17 - Explain why the mechanical and physical properties...Ch. 17 - What are the effects of the different shapes and...Ch. 17 - Describe the relative advantages and limitations...Ch. 17 - How different, if any, are the requirements for...Ch. 17 - The powder metallurgy process can be competitive...Ch. 17 - What are the reasons for the shapes of the shown...Ch. 17 - Should green compacts be brought up to the...Ch. 17 - Because they undergo special processing, metal...Ch. 17 - In Fig. 17.12, it can be seen that the pressure is...Ch. 17 - Why do the compacting pressure and the sintering...Ch. 17 - What will be stronger: a blend of stainless steel...Ch. 17 - Name the various methods of powder production and...Ch. 17 - Estimate the maximum tonnage required to compact a...Ch. 17 - Refer to Fig. 17.11a. What should be the volume of...Ch. 17 - Determine the shape factors for (a) a cylinder...Ch. 17 - Estimate the number of particles in a 500-g sample...Ch. 17 - Prob. 37QTPCh. 17 - A coarse copper powder is compacted in a...Ch. 17 - A gear is to be manufactured from iron powders. It...Ch. 17 - What volume of powder is needed to make the gear...Ch. 17 - The axisymmetric part shown in Fig. P17.41 is to...Ch. 17 - Prepare an illustration similar to Fig. 13.1,...Ch. 17 - Prob. 44SDPCh. 17 - Compare the design considerations for PM products...Ch. 17 - Prob. 46SDPCh. 17 - Prob. 47SDPCh. 17 - Using the Internet, locate suppliers of metal...Ch. 17 - Explain why powder metal parts are commonly used...Ch. 17 - Prob. 50SDPCh. 17 - Describe how the information given in Fig. 17.15...Ch. 17 - It was stated that, in the process shown in Fig....Ch. 17 - Prob. 53SDPCh. 17 - The axisymmetric parts shown in Fig. P17.54 are to...Ch. 17 - Assume you are working in technical sales. What...
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
Recommended textbooks for you
Text book image
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Text book image
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Text book image
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Text book image
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Text book image
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Text book image
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
SEE MORE TEXTBOOKS