EBK AUTOMOTIVE TECHNOLOGY
5th Edition
ISBN: 8220100659843
Author: Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 17, Problem 4RQ
What are four lubricants that a manual transmission/transaxle may require, depending on exact year, make, and model of the vehicle.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Why do you think a 5-speed manual Ford Mustang is geared as followed?
Gear 1, 3.35:1 Ratio
Gear 2, 1.93:1 Ratio
Gear 3, 1.29:1 Ratio
Gear 4, 1.00:1 Ratio
Gear 5, 0.68:1 Ratio (Overdrive)
Question 1
The coefficient of efficiencies between different transmission elements are not usually at the same
value. Table 1 below, shows the efficiencies of different transmission elements. Analyze table 1
and answer the questions below.
Table 1: Coefficient of Efficiencies between the transmission elements
Coefficient
Types of Transmission or
Support
of
Efficiency
Belt Drive with flat belt
0.98
Belt drive with V-Belt
0.96
Spur Gear drive
Helical Gear Drive
0.98
0.97
Bevel Gear Drive
0.96
Ball or Roller Bearing
0.995
Crank and Slider mechanism
Jaw Clutch
Multiple-disc friction clutch
operating in oil
0.9
0.95
0.9
a) How are these coefficient values are calculated?
b) Base on your analysis, why the value of Belt Drive with V-Belt is having a lower coefficient
compared to flat belt?
c) Define the highest coefficient of efficiency and state one (1) reason of why.
What is the importance of studying on how to pull-out and mount manual transmission?
Chapter 17 Solutions
EBK AUTOMOTIVE TECHNOLOGY
Ch. 17 - Why should brake fluid not be filled above the...Ch. 17 - Why should brake fluid be kept in an airtight...Ch. 17 - How do you check differential fluid?Ch. 17 - What are four lubricants that a manual...Ch. 17 - When should the engine oil be replaced? a....Ch. 17 - Prob. 2CQCh. 17 - Prob. 3CQCh. 17 - Prob. 4CQCh. 17 - Coolant can be checked using ____________. a....Ch. 17 - Accessory drive belt tension is determined by...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Find the change in length of side AB.
Mechanics of Materials, 7th Edition
Consider a subsonic compressible flow in cartesian coordinates where the velocity potential is given by (x,y)=V...
Fundamentals of Aerodynamics
Describe the structural changes that take place when a plain-carbon eutectoid steel is slowly cooled from the a...
Foundations of Materials Science and Engineering
How is the hydrodynamic entry length defined for flow in a pipe? Is the entry length longer in laminar or turbu...
Fluid Mechanics Fundamentals And Applications
What is the importance of modeling in engineering? How are the mathematical models for engineering processes pr...
Heat and Mass Transfer: Fundamentals and Applications
Locate the centroid of the area. Prob. 9-17
Engineering Mechanics: Statics
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Why do we need to follow the precautionary measures and safety procedures when performing pulling-out and mounting manual transmission?arrow_forwardWhat should you do to properly identify the type of transmission you are working on?arrow_forwardThe typical RWD drive shaft rotates how many times faster than wheelsarrow_forward
- the epicyclic gear train? 2- Why does efficiency increase with increasing load? VWhat is the reas on for the differ ence betwe en practi cal and theoretical efficien cy? 3- What is the function of the epicyclic system in the car when turning? Please write the ansv wer in word, not in hand writi ngarrow_forwardWhen servicing transfer cases, all of the following are correct, except_____. a. it must be supported on a transmission jack or safety stands b. the chain drive and a planetary gearset must be adjusted to specifications c. visual inspections for leaks and damage are necessary d. follow the manufacturers recommendations for lubricantsarrow_forwardIn a manual transmission what are the seven steps for power flow in final drivearrow_forward
- what are the mechanical differences between 4 wheel drive, front wheel drive and rear wheel drive systems?arrow_forwardTechnician A says that a prerequisite to accurate road-testing analysis is knowing what planetary controls are applied in a particular gear range. Technician B says that all slipping conditions can be traced to a leaking hydraulic circuit. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhy do we need to diagnose the transmission/transaxle failure?arrow_forward
- Braking torque applied?arrow_forward108) Technician A says that engine management malfunctions may be misinterpreted as transmission malfunction. Technician B says that imbalance in driveline components or wheels may be a likely cause of vibration. Which technician is correct? O Technician A O Technician B O Both technicians A and B O Neither technician A nor Barrow_forward32. Technician A says hypoid gearset are only used in RWD vehicle drivetrains. Technician B says hypoid gearset multiply torque. Which technician is correct? A- Technician A B- Technician B C- Both A and B D- Neither A nor B.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License