Concept explainers
A bullet weighing 0.08 lb is fired with a horizontal velocity of 1800 ft/s into the lower end of a slender 15-lb bar of length L = 30 in. Knowing that h = 12 in. and that the bar is initially at rest, determine (a) the angular velocity of the bar immediately after the bullet becomes embedded, (b) the impulsive reaction at C, assuming that the bullet becomes embedded in 0.001 s.
Fig. P17.97
Trending nowThis is a popular solution!
Chapter 17 Solutions
Vector Mechanics for Engineers: Statics and Dynamics
Additional Engineering Textbook Solutions
Introduction to Heat Transfer
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
Machine Elements in Mechanical Design (6th Edition) (What's New in Trades & Technology)
Fluid Mechanics Fundamentals And Applications
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Fundamentals of Heat and Mass Transfer
- A uniform rod of mass m and length 5 a is bent into the shape shown and is suspended from a wire attached at point B. Knowing that the rod is hit at point A in the negative y direction and denoting the corresponding impulse by determine immediately after the impact (a) the velocity of the mass center G, (b) the angular velocity of the rod.arrow_forwardDisk A, of weight 5 lb and radius r = 3 in., is at rest when it is placed in contact with a belt that moves at a constant speed v = 50 ft/s. Knowing that μk = 0.20 between the disk and the belt, determine the time required for the disk to reach a constant angular velocity.arrow_forwardEach of the gears A and B has a mass of 675 g and a radius of gyration of 40 mm, while gear C has a mass of 3.6 kg and a radius of gyration of 100 mm. Assume that kinetic friction in the bearings of gears A, B C produces couples of constant magnitude 0.15 N.m, 0.15 N.m, 0.3 N.m, respectively. Knowing that the initial angular velocity of gear C is 2000 rpm, determine the time required for the system to come to rest.arrow_forward
- The ends of a 9-lb bar AB are constrained to move along slots cut in a vertical plate as shown. A resource of constant k = 3 lb/in. is attached to end A such that its tension is zero when e=0. If the bar is released from rest when e = 0, determine the angular velocity of the bar and the velocity of end B when =30°arrow_forwardA slender 9-lb rod can rotate in a vertical plane about a pivot at B. A spring of constant k = 30 lb/ft and of unstretched length 6 in. is attached to the rod as shown. Knowing that the rod is released from rest in the position shown, determine its angular velocity after it has rotated through 90°.arrow_forwardA 1200-kg satellite designed to study the sun has an angular velocity of w0 = (0.050 rad/s)i + (0.075 rad/s)k when two small jets are activated at A and B in a direction parallel to the y axis. Knowing that the coordinate axes are principal centroidal axes, that the radii of gyration of the satellite are and that each jet produces a 50-N thrust, determine (a ) the required operating time of each jet if the angular velocity of the satellite is to be reduced to zero, (b ) the resulting change in the velocity of the mass center G.arrow_forward
- The ABC bar has a mass of 2.4 kg and is connected to a support on B. An 800 g D sphere reaches the end A of the bar with a vertical velocity v1 of 3 m / s. Knowing that L = 750 mm and that the coefficient of refund between the sphere and the ABC bar is equal to 0.5, determine immediately after the shock, the angular velocity of the ABC bar and the velocity of the sphere.arrow_forwardTwo uniform rods, each of mass m, form the L-shaped rigid body ABC, which is initially at rest on the frictionless horizontal surface when hook D of the carriage E engages a small pin at C. Knowing that the carriage is pulled to the right with a constant velocity v0, determine immediately after the impact (a) the angular velocity of the body, (b) the velocity of corner B. Assume that the velocity of the carriage is unchanged and that the impact is perfectly plastic.arrow_forwardA slender 9-lb rod can rotate in a vertical plane about a pivot at B. A spring of constant k = 21 lb/ft and of unstretched length 6 in. is attached to the rod as shown in the figure. Knowing that the rod is released from rest in the position shown in the figure, determine its angular velocity after it has rotated through 90 degree .arrow_forward
- A 18-kg rear hatch of a vehicle opens as shown in the figure and can be modeled as a uniform 0.6-m long slender rod. Knowing that the tailgate is released from rest in the position shown in the figure, determine the angular velocity of the tailgate as it impacts the car body.arrow_forwardA semicircular panel with a radius r is attached with hinges to a circular plate with a radius r and initially is held in the vertical position as shown. The plate and the panel are made of the same material and have the same thickness. Knowing that the entire assembly is rotating freely with an initial angular velocity of w0 , determine the angular velocity of the assembly after the panel has been released and comes to rest against the plate.arrow_forwardA uniform slender bar of length L = 200 mm and mass m = 0.5 kg is supported by a frictionless horizontal table. Initially the bar is spinning about its mass center G with a constant angular speed w1 = 6 rad/s. Suddenly latch D is moved to the right and is struck by end A of the bar. Knowing that the coefficient of restitution between A and D is e= 0.6, determine the angular velocity of the bar and the velocity of its mass center immediately after the impact.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY