Engineering Mechanics: Statics & Dynamics (14th Edition)
14th Edition
ISBN: 9780133915426
Author: Russell C. Hibbeler
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 18.4, Problem 3P
The wheel is made from a 5-kg thin ring and two 2-kg slender rods. If the torsional spring attached to the wheel's center has a stiffness k = 2 N · m/rad, so that the torque on the center of the wheel is M = (2θ) N · m, where θ is in radians, determine the maximum angular velocity of the wheel if it is rotated two revolutions and then released from rest
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
If the cord is subjected to a horizontal force of P = 150 N, and gear is supported by a fixed pin at O,determine the angular velocity of the gear and the velocity of the 20-kg gear rack in 4 s, starting from rest. The mass of the gear is 50 kg and it has a radius of gyration of k0 = 125 mm. Assume that the contact surface between the gear rack and the horizontal plane is smooth.
The platform AB when empty has a mass of 400 kg centre of mass at G1 and natural period of oscillation t1=3.82 s. If a car, having a mass of 1.2 Mg and centre of mass at G2 is placed on the platform, the natural period of oscillation becomes t1=4.58 s. Determine the moment of inertia of the car about an axis passing through G2.
The wheel has a mass of 100 kg and a radius of gyration of kO = 0.2 m. A motor supplies a torque M = (40u + 900) N #m, where u is in radians, about the drive shaft at O. Determine the speed of the loading car, which has a mass of 300 kg, after it travels s = 4 m. Initially the car is at rest when s = 0 and u = 0°. Neglect the mass of the attached cable and the mass of the car’s wheels
Chapter 18 Solutions
Engineering Mechanics: Statics & Dynamics (14th Edition)
Ch. 18.4 - Determine the kinetic energy of the 100-kg object.Ch. 18.4 - The 80-kg wheel has a radius of gyration about its...Ch. 18.4 - The uniform 50-lb slender rod is subjected to a...Ch. 18.4 - The uniform 50-kg slender rod is at rest m the...Ch. 18.4 - The 50-kg wheel is subjected to a force of 50 N....Ch. 18.4 - If the uniform 30-kg slender rod starts from rest...Ch. 18.4 - The 20-kg wheel has a radius of gyration about its...Ch. 18.4 - At a given instant the body of mass m has an...Ch. 18.4 - The wheel is made from a 5-kg thin ring and two...Ch. 18.4 - The wheel is made from a 5-kg thin ring and two...
Ch. 18.4 - A force of P = 60 N is applied to the cable, which...Ch. 18.4 - A force of P = 20 N is applied to the cable, which...Ch. 18.4 - A force of P = 20 N is applied to the cable, which...Ch. 18.4 - The double pulley consists of two parts that are...Ch. 18.4 - The double pulley cons1sts of two parts that are...Ch. 18.4 - Prob. 9PCh. 18.4 - The spool has a mass of 40 kg and a radius of...Ch. 18.4 - Prob. 11PCh. 18.4 - Determine the velocity of the 50-kg cylinder after...Ch. 18.4 - The 10-kg uniform slender rod is suspended at rest...Ch. 18.4 - Prob. 14PCh. 18.4 - The pendulum consists of a 10-kg uniform disk and...Ch. 18.4 - A motor supplies a constant torque M = 6 kNm to...Ch. 18.4 - The center O of the thin ring of mass m is given...Ch. 18.4 - Prob. 18PCh. 18.4 - Prob. 19PCh. 18.4 - If P = 200 N and the 15-kg uniform slender rod...Ch. 18.4 - A yo-yo has a weight of 0.3 lb and a radius of...Ch. 18.4 - Prob. 22PCh. 18.4 - Prob. 23PCh. 18.4 - Prob. 24PCh. 18.4 - The 30-kg disk is originally at rest, and the...Ch. 18.4 - Two wheels of negligible weight are mounted at...Ch. 18.4 - Prob. 27PCh. 18.4 - The 10-kg rod AB is pin connected at A and...Ch. 18.4 - The 10-lb sphere starts from rest at = 0 and...Ch. 18.4 - Motor M exerts a constant force of P = 750 Non the...Ch. 18.4 - Prob. 31PCh. 18.4 - The linkage consists of two 6-kg rods AB and CD...Ch. 18.4 - The two 2-kg gears A and B are attached to the...Ch. 18.4 - The linkage consists of two 8-lb rods AB and CD...Ch. 18.4 - The linkage consists of two 8-lb rods AB and CD...Ch. 18.5 - F187. If the 30-kg disk is released from rest when...Ch. 18.5 - The 50-kg reel has a radius of gyration about its...Ch. 18.5 - The 60-kg rod OA is released from rest when = 0....Ch. 18.5 - Prob. 10FPCh. 18.5 - The 30-kg rod is released from rest when = 45....Ch. 18.5 - Prob. 12FPCh. 18.5 - Prob. 36PCh. 18.5 - Prob. 37PCh. 18.5 - An automobile tire has a mass of 7 kg and radius...Ch. 18.5 - The spool has a mass of 20 kg and a radius of...Ch. 18.5 - The spool has o mass of 20 kg and a radius of...Ch. 18.5 - A uniform ladder having a weight of 30 lb is...Ch. 18.5 - Prob. 44PCh. 18.5 - The 12-kg slender rod is attached to a spring,...Ch. 18.5 - Prob. 46PCh. 18.5 - The 40-kg wheel has a radius of gyration about its...Ch. 18.5 - The assembly consists of two 10-kg bars which are...Ch. 18.5 - The assembly consists of two 10-kg bars which are...Ch. 18.5 - The compound disk pulley consists of a hub and...Ch. 18.5 - Prob. 51PCh. 18.5 - Prob. 52PCh. 18.5 - The two 12-kg slender rods are pin connected and...Ch. 18.5 - If the 250-lb block is released from rest when the...Ch. 18.5 - The slender 15-kg bar is initially at rest and...Ch. 18.5 - If the chain is released from rest from the...Ch. 18.5 - Prob. 57PCh. 18.5 - Prob. 58PCh. 18.5 - The slender 6-kg bar AB is horizontal and at rest...Ch. 18.5 - Prob. 60PCh. 18.5 - Prob. 61PCh. 18.5 - The 50-lb wheel has a radius of gyration about its...Ch. 18.5 - The system consists of 60-lb and 20-lb blocks A...Ch. 18.5 - The door is made from one piece, whose ends move...Ch. 18.5 - Prob. 65PCh. 18.5 - Prob. 66PCh. 18.5 - Prob. 67PCh. 18.5 - The system consists of a 30-kg disk A, 12-kg...Ch. 18.5 - The pendulum of the Charpy impact machine has a...Ch. 18.5 - Prob. 2RPCh. 18.5 - The drum has a mass of 50 kg and a radius of...Ch. 18.5 - The spool has a mass of 60 Kg and a radius of...Ch. 18.5 - Prob. 5RPCh. 18.5 - At the Instant shown, the 50-lb bar rotates...Ch. 18.5 - Prob. 7RPCh. 18.5 - Prob. 8RP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The spring-held follower AB has a mass of 0.4 kg and moves back and forth as its end rolls on the contoured surface of the cam, where r = 0.15 m and z=(0.02cos2θ)m. The cam is rotating at a constant rate of 30 rad/s. The spring is uncompressed when θ = 90. Determine the maximum force component FzFz the follower exerts on the cam. Determine the minimum force component FzFz the follower exerts on the cam.arrow_forwardGears A and B each have a mass of 2.4 kg and a radius of gyration of 60 mm, while gear C has a mass of 12 kg and a radius of gyration of 150 mm. A torque M with constant magnitude of 10 N.m to gear C. Determine a) the number of revolutions of gear C that is required for its angular velocity to increase from 100 to 450 rpm. b) the corresponding tangential force acting on gear A Please include the free body diagram if necessary.arrow_forwardThe body and bucket of a skid steer loader has a weight of 2000 lb, and its center of gravity is located at G. Each of the four wheels has a weight of 100 lb and a radius of gyration about its center of gravity of 1ft. If the engine supplies a torque of M = 100 lb ft to each of the rear drive wheels, determine the speed of the loader in t = 10 s starting from rest. The wheels roll without slippingarrow_forward
- The double pulley consists of two wheels which are attached to one another and turn at the same rate. The pulley has a mass of 15 kg and a radius of gyration kO=110mm. If the block at A has a mass of 40 kg, determine the speed of the block in 3 s after a constant force F=2kN is applied to the rope wrapped around the inner hub of the pulley. The block is originally at rest. Neglect the mass of the rope.arrow_forwardThe spool has a mass of 200 kg and a radius of gyration of kG = 0.2 m. If the coefficients of static and kinetic friction at A are μs = 0.3 and μk = 0.2, respectively, determine the angularacceleration of the spool if P = 400 N.arrow_forwardAssuming there is no slippage for the belt assembly below, Determine the following: What is the average angular velocity of each pulley if the rope accelerates from 5 m/s to 10 m/s in 10 s? How many revolutions does the pulley turn in that time? R1 = 0.3 m R2 = 0.2 m R3 = 0.1 marrow_forward
- The 10-kg uniform slender rod is suspended at rest when the force of F = 150 N is applied to its end. Determine the angular velocity of the rod when it has rotated 180° clockwise from the position shown. The force is always perpendicular to the rod.arrow_forwardWhile the system shown is in equilibrium, a counter-clockwise torque T =T0sin(ωt) N-m(with T0 = 226.6 and ω=7) is applied to teh disk. What is the disk angular speed ω0 = ? in rad/s at time t = 4.2 sec? ( I = 0.2 kg.m2, b = 7.8 N-m-s/r, k = 1,504 N/m, r = 0.52m )arrow_forwardIn the figure, rod AB has a mass of 10 kg, and must slide within the slots as shown. If the spring is unstretched when θ = 0°, determine the angular velocity of the bar when it reaches that angle after being released from θ = 30°.arrow_forward
- Prove the relation that Hammer blow = ± mb x r*x ω2 where mb = Balancing mass placed at a radius of r* and ω= angular speed of the crank.arrow_forwardThe 3.8 kg block is descending at a rate of 1.2 m/s when the hydraulic cylinder BC exerts a force F=500 N on the brake arm. Determine the number of radians the wheel will rotate before the system comes to rest. The wheel has a mass of 25 kg and a radius of gyration about its center kO=300 mm. The coefficient of kinetic friction between the brake arm and the wheel is 0.25.arrow_forwardThe drum, with radius R = 1.9 m, is given an initial counterclockwise angular velocity ω0. The drum is kept from rolling towards the left by a smooth vertical slot acting on a thin rod which passes through its centre. A vertical force (where C = 38, k = 1.7 and t denotes time in seconds) is being applied to a cord wrapped around the inner hub, with radius r = 0.7 m, of the drum. If the frictional coefficient is μk = 0.62 and the change in the angular momentum about O is ΔHO = 238 kg.m2/s (counterclockwise) during the first 2.3 seconds, determine the mass of the drum. (The mass of the cord and the thin rod may be regarded as negligible.) a)214.2 kg b)68.28 kg c)19.83 kg d)109.6 kg e)69.86 kgarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
First Law of Thermodynamics, Basic Introduction - Internal Energy, Heat and Work - Chemistry; Author: The Organic Chemistry Tutor;https://www.youtube.com/watch?v=NyOYW07-L5g;License: Standard youtube license