Engineering Mechanics: Statics & Dynamics (14th Edition)
14th Edition
ISBN: 9780133915426
Author: Russell C. Hibbeler
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 18.5, Problem 7RP
To determine
The velocity of the collar when the rod becomes horizontal.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The 7.5-lb disk A has a radius r A = 6 in. and is initially at rest. The 10-lb disk B has a radius r B = 8 in. and an angular velocity w0 of 900 rpm when it is brought into contact with disk A. Neglecting friction in the bearings, determine (a) the final angular velocity of each disk, (b) the total impulse of the friction force exerted on disk A.
The 10-kg uniform cylinder is pin supported at its center O. The square isacted upon by a constant force F = 10N and a constant couple moment M = 10 Nm.If the disk starts from rest, determine1) The reactions at the pin O and the angular acceleration of the disk2) The number of revolutions it must take to attain an angular velocity of 10 rad/s
The 12-kg slender rod is pinned to a small roller A
that slides freely along the slot. If the rod is released from
rest at f) = 0°, determine the angular acceleration of the rod
and the acceleration of the roller immediately after the
release.
Chapter 18 Solutions
Engineering Mechanics: Statics & Dynamics (14th Edition)
Ch. 18.4 - Determine the kinetic energy of the 100-kg object.Ch. 18.4 - The 80-kg wheel has a radius of gyration about its...Ch. 18.4 - The uniform 50-lb slender rod is subjected to a...Ch. 18.4 - The uniform 50-kg slender rod is at rest m the...Ch. 18.4 - The 50-kg wheel is subjected to a force of 50 N....Ch. 18.4 - If the uniform 30-kg slender rod starts from rest...Ch. 18.4 - The 20-kg wheel has a radius of gyration about its...Ch. 18.4 - At a given instant the body of mass m has an...Ch. 18.4 - The wheel is made from a 5-kg thin ring and two...Ch. 18.4 - The wheel is made from a 5-kg thin ring and two...
Ch. 18.4 - A force of P = 60 N is applied to the cable, which...Ch. 18.4 - A force of P = 20 N is applied to the cable, which...Ch. 18.4 - A force of P = 20 N is applied to the cable, which...Ch. 18.4 - The double pulley consists of two parts that are...Ch. 18.4 - The double pulley cons1sts of two parts that are...Ch. 18.4 - Prob. 9PCh. 18.4 - The spool has a mass of 40 kg and a radius of...Ch. 18.4 - Prob. 11PCh. 18.4 - Determine the velocity of the 50-kg cylinder after...Ch. 18.4 - The 10-kg uniform slender rod is suspended at rest...Ch. 18.4 - Prob. 14PCh. 18.4 - The pendulum consists of a 10-kg uniform disk and...Ch. 18.4 - A motor supplies a constant torque M = 6 kNm to...Ch. 18.4 - The center O of the thin ring of mass m is given...Ch. 18.4 - Prob. 18PCh. 18.4 - Prob. 19PCh. 18.4 - If P = 200 N and the 15-kg uniform slender rod...Ch. 18.4 - A yo-yo has a weight of 0.3 lb and a radius of...Ch. 18.4 - Prob. 22PCh. 18.4 - Prob. 23PCh. 18.4 - Prob. 24PCh. 18.4 - The 30-kg disk is originally at rest, and the...Ch. 18.4 - Two wheels of negligible weight are mounted at...Ch. 18.4 - Prob. 27PCh. 18.4 - The 10-kg rod AB is pin connected at A and...Ch. 18.4 - The 10-lb sphere starts from rest at = 0 and...Ch. 18.4 - Motor M exerts a constant force of P = 750 Non the...Ch. 18.4 - Prob. 31PCh. 18.4 - The linkage consists of two 6-kg rods AB and CD...Ch. 18.4 - The two 2-kg gears A and B are attached to the...Ch. 18.4 - The linkage consists of two 8-lb rods AB and CD...Ch. 18.4 - The linkage consists of two 8-lb rods AB and CD...Ch. 18.5 - F187. If the 30-kg disk is released from rest when...Ch. 18.5 - The 50-kg reel has a radius of gyration about its...Ch. 18.5 - The 60-kg rod OA is released from rest when = 0....Ch. 18.5 - Prob. 10FPCh. 18.5 - The 30-kg rod is released from rest when = 45....Ch. 18.5 - Prob. 12FPCh. 18.5 - Prob. 36PCh. 18.5 - Prob. 37PCh. 18.5 - An automobile tire has a mass of 7 kg and radius...Ch. 18.5 - The spool has a mass of 20 kg and a radius of...Ch. 18.5 - The spool has o mass of 20 kg and a radius of...Ch. 18.5 - A uniform ladder having a weight of 30 lb is...Ch. 18.5 - Prob. 44PCh. 18.5 - The 12-kg slender rod is attached to a spring,...Ch. 18.5 - Prob. 46PCh. 18.5 - The 40-kg wheel has a radius of gyration about its...Ch. 18.5 - The assembly consists of two 10-kg bars which are...Ch. 18.5 - The assembly consists of two 10-kg bars which are...Ch. 18.5 - The compound disk pulley consists of a hub and...Ch. 18.5 - Prob. 51PCh. 18.5 - Prob. 52PCh. 18.5 - The two 12-kg slender rods are pin connected and...Ch. 18.5 - If the 250-lb block is released from rest when the...Ch. 18.5 - The slender 15-kg bar is initially at rest and...Ch. 18.5 - If the chain is released from rest from the...Ch. 18.5 - Prob. 57PCh. 18.5 - Prob. 58PCh. 18.5 - The slender 6-kg bar AB is horizontal and at rest...Ch. 18.5 - Prob. 60PCh. 18.5 - Prob. 61PCh. 18.5 - The 50-lb wheel has a radius of gyration about its...Ch. 18.5 - The system consists of 60-lb and 20-lb blocks A...Ch. 18.5 - The door is made from one piece, whose ends move...Ch. 18.5 - Prob. 65PCh. 18.5 - Prob. 66PCh. 18.5 - Prob. 67PCh. 18.5 - The system consists of a 30-kg disk A, 12-kg...Ch. 18.5 - The pendulum of the Charpy impact machine has a...Ch. 18.5 - Prob. 2RPCh. 18.5 - The drum has a mass of 50 kg and a radius of...Ch. 18.5 - The spool has a mass of 60 Kg and a radius of...Ch. 18.5 - Prob. 5RPCh. 18.5 - At the Instant shown, the 50-lb bar rotates...Ch. 18.5 - Prob. 7RPCh. 18.5 - Prob. 8RP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The assembly consists of a 3-kg pulley A and 10-kg pulley B. If a 2-kg block is suspended from the cord, determine the distance the block must descend, starting from rest, in order to cause B to have an angular velocity of 6 rad/s. Neglect the mass of the cord and treat the pulleys as thin disks. No slipping occurs.arrow_forwardThe plank AB has a mass of 7 kg. The rollers D and E are each of mass 5kg and are 0.5 m in diameter. The plank is released from rest with roller D under the end A and the roller E, under the mass center C. assuming no slipping, determine the velocity of the plank when roller E is under end B.arrow_forwardThe trailer has a mass of 400kg and the mass center at G. is being pulled by a horizontal force of magnitude of F = 800N. Determine the acceleration of the trailer, as well as the normal forces (Na and Nb) on the pair of wheels at A and B respectively. Assume the wheels are free to roll and have negligible mass.arrow_forward
- 5. The 25-kg block AA is released from rest.arrow_forwardThe 10-gg bullet having a velocity of vvv = 750 m/sm/s is fired into the edge of the 4-kgkg disk as shown. The disk is originally at rest. The rod ABAB has a mass of 3 kg Determine the magnitude of the angular velocity of the disk just after the bullet becomes embedded into its edge. Calculate the angle θθ the disk will swing when it stops.arrow_forwardThe 2.5-kgkg rod ACBACB supports the two 4.1-kgkg disks at its ends. If both disks are given a clockwise angular velocity (ωA)1=(ωB)1=4.6rad/s(ωA)1=(ωB)1=4.6rad/s while the rod is held stationary and then released, determine the angular velocity of the rod after both disks have stopped spinning relative to the rod due to frictional resistance at the pins AA and BB. Motion is in the horizontal plane. Neglect friction at pin CC.arrow_forward
- In the equilibrium position, the 30 kg cylinder causes a static deflection of [60] mm in the coiled spring. If the cylinder is depressed an additional [45] mm and released from rest, calculate: The position , velocity and acceleration of the cylinder at t = 1.2 s.arrow_forwardThe double pulley consists of two wheels which are attached to one another and turn at the same rate. The pulley has a mass of 15 kg and a radius of gyration kO=110mm. If the block at A has a mass of 40 kg, determine the speed of the block in 3 s after a constant force F=2kN is applied to the rope wrapped around the inner hub of the pulley. The block is originally at rest. Neglect the mass of the rope.arrow_forwardThe particle of mass m = 2.4 kg is attached to the light rigid rod of length L = 0.77 m, and the assembly rotates about a horizontal axis through O with a constant angular velocity θ˙θ˙ = ω = 3.5 rad/s. Determine the force T in the rod when θ = 29°. The force T is positive if in tension, negative if in compression.arrow_forward
- The 10-kg rod AB shown is confined so that its ends move in the horizontal andvertical slots. The spring has a stiffness of k = 800N/m and is unstretched when θ = 0˚.Determine the angular velocity of AB when θ = 0˚, if the rod is released from rest when θ = 30˚.Neglect the mass of the slider blocks. It’s frictionless.arrow_forwardThe 100-kg spool is resting on the inclined surface for which the coefficient of kinetic friction is μk = 0.13. The radius of gyration about the mass center is kG = 0.22 m Determine the angular velocity of the spool, measured clockwise, when t = 7 s after it is released from rest. Express your answer using three significant figures. Enter positive value if the angular velocity is clockwise and negative value if the angular velocity is counterclockwisearrow_forwardThe 25-kg cylinder A is free to slide along rod BC. When the cylinder is at x=0, the 46-kg circular disk D is rotating with an angular velocity of 4.8 rad/s. (Figure 1) If the cylinder is given a slight push, determine the angular velocity of the disk when the cylinder strikes B at x=600mm. Neglect the mass of the brackets and the smooth rod.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License