EP ENGR.MECH.-MOD.MASTERING ACCESS
15th Edition
ISBN: 9780134867267
Author: HIBBELER
Publisher: PEARSON CO
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 19, Problem 39P
The 12-kg rod AB is pinned to the 40-kg disk. If the disk is given an angular velocity ωD = 100 rad/s while the rod is held stationary, and the assembly 15 then released, determine the angular velocity of the rod after the disk has stopped spinning relative to the rod due to frictional resistance at the bearing B. Motion is in the horizontal plane. Neglect friction at the pin A.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The 10-kg uniform slender rod is suspended at rest when the force of F = 150 N is applied to its end. Determine the angular velocity of the rod when it has rotated 180° clockwise from the position shown. The force is always perpendicular to the rod.
The 5-kg cylinder is initially at rest when it is placed in contact with the wall B and the rotor at A.
If the rotor always maintains a constant clockwise angular velocity, determine the initial angular
acceleration of the cylinder. The coefficient of kinetic friction at the contacting surfaces B and C is k
0.2.
=
B
125 mm
45°
1. The 6-kg cylinder is initially at rest when it is placed in contact with the wall B and the rotor at A.
If the rotor always maintains a constant clockwise angular velocity w = 7 rad/s, determine the
initial angular acceleration of the cylinder. The coefficient of kinetic friction at the contacting
surfaces B and Cis Hx = 0.2.
B
125 mm
45
Chapter 19 Solutions
EP ENGR.MECH.-MOD.MASTERING ACCESS
Ch. 19 - The 60-kg wheel has a radius of gyration about its...Ch. 19 - Prob. 2FPCh. 19 - Prob. 3FPCh. 19 - Gears A and B of mass 10 kg and 50 kg have radii...Ch. 19 - The 50-kg spool is subjected to a horizontal force...Ch. 19 - Prob. 6FPCh. 19 - The rigid body (slab) has a mass m and rotates...Ch. 19 - Prob. 2PCh. 19 - Show that if a slab is rotating about a fixed axis...Ch. 19 - Prob. 21P
Ch. 19 - The two gears A and B have weights and radii of...Ch. 19 - The 30-kg gear is subjected to a force of P =...Ch. 19 - Prob. 27PCh. 19 - The turntable T of a record player has a mass of...Ch. 19 - The 10-g bullet having a velocity of 800 m/s is...Ch. 19 - Prob. 31PCh. 19 - Disk A has a weight of 20 lb. An inextensible...Ch. 19 - The 12-kg rod AB is pinned to the 40-kg disk. If...Ch. 19 - A thin rod of mass m has an angular velocity o...Ch. 19 - Prob. 41PCh. 19 - Prob. 42PCh. 19 - Prob. 44PCh. 19 - The 10-lb block is sliding on the smooth surface...Ch. 19 - Prob. 46PCh. 19 - The pendulum consists of a 15-kg solid ball and...Ch. 19 - Prob. 48PCh. 19 - The 20-kg disk strikes the step Without...Ch. 19 - The solid ball of mass m is dropped with a...Ch. 19 - Prob. 54PCh. 19 - Prob. 55PCh. 19 - Prob. 56PCh. 19 - Prob. 58PCh. 19 - The cable is subjected to a force of P = (10t2)...Ch. 19 - Prob. 2RPCh. 19 - The tire has a mass of 9 kg and a rad1us of...Ch. 19 - Prob. 4RPCh. 19 - The spool has a weight of 30 lb and a radius of...Ch. 19 - Prob. 6RPCh. 19 - Prob. 7RPCh. 19 - Prob. 8RP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The small end rollers of the 8-lb uniform slender bar (length = 4 ft) are constrained to move in the slots, which lie in the verticalplane. At the instant when θ = 30°, the velocity of roller A is 14 ft/s down the vertical slot. Determine the angular acceleration of the bar, the acceleration of mass center G, and the reactions of points A and B, under the action of the 6-lb force P. Neglect the friction and the mass of the small rollers.arrow_forwardThe 10-kg wheel is rolling under the constant moment of M = 97 N-m. The wheel has radius r= 0.59 m, has mass center at point G, and the radius of gyration is kg = 0.27 m. The coefficients of friction between the wheel and the ground is ls = 0.25 and Hk = 0.14. If the wheel rolls while slipping, determine the magnitude of the linear acceleration of point G (in m/s2). Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s?. M Garrow_forwardThe uniform 80 kg slender rod is at rest in the position shown when P = 450 N is applied. Determine the value of angular velocity, w2 the rod if L1 = 5.5 m and L2 = 6.5 m. A L L2 L1 Barrow_forward
- The 10-kg rod AB shown is confined so that its ends move in the horizontal andvertical slots. The spring has a stiffness of k = 800N/m and is unstretched when θ = 0˚.Determine the angular velocity of AB when θ = 0˚, if the rod is released from rest when θ = 30˚.Neglect the mass of the slider blocks. It’s frictionless.arrow_forwardThe 29-kg wheel is rolling under the constant moment of M = 85 N·m. The wheel has radius r = 0.57 m, has mass center at point G, and the radius of gyration is kg = 0.25 m. The coefficients of friction between the wheel and the ground is g = 0.37 and μk = 0.16. If the wheel rolls while slipping, determine the magnitude of the linear acceleration of point G (in m/s²). Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s². M Your Answer: Answerarrow_forwardThe 12-kg slender rod is pinned to a small roller that slides freely in the slot. If the rod is released from rest with θ = 0o , determine the angular acceleration of the rod and the linear acceleration of the center of mass immediately after release.arrow_forward
- The small end rollers of the 6.2-lb uniform slender bar are constrained to move in the slots, which lie in a vertical plane. At the instant when e = 30°, the angular velocity of the bar is 2.6 rad/sec counterclockwise. Determine the angular acceleration of the bar, the reactions at A and B, and the accelerations of points A and B under the action of the 5.1-lb force P. Neglect the friction and mass of the small rollers. The angular acceleration is positive if counterclockwise, negative if clockwise. The acceleration of A is positive if downward, negative if upward. The acceleration of B is positive if down the slot, negative if up the slot. The reaction at A Is positive If to the right, negative If to the left. The reaction at 8 Is positive If up and to the right, negative If down and to the left. L= 5.2 ft 107 P= 5.1 lb Answers: Jad/sec? F = Fg =arrow_forwardThe 13.5-lblb disk rests on the 5-lblb plate. A cord is wrapped around the periphery of the disk and attached to the wall at BB. A torque MM = 40 lb⋅ftlb⋅ft is applied to the disk. Assume the disk does not slip on the plate and the plate rests on the surface at DD having a coefficient of kinetic friction of μkμk = 0.2. Neglect the mass of the Determine the angular acceleration of the disk measured counterclockwise . Determine the time needed for the end CC of the plate to travel 3 ftft and strike the wall.arrow_forwardQ8: The 25-kg bar BD is attached to the two light links AB and CD and moves in the vertical plane. The lower link is subjected to a clockwise torque M = 200 N. m applied through its shaft at A. If each link has an angular velocity w = 5 rad/s as it passes the horizontal position, calculate the force which the upper link exerts on the bar at D at this instant. Also find the angular acceleration of the links at this position. Ans.: F, = 234 N, a = 5.87 rad/s² CW D 300 mm 500 mm M B 600 mmarrow_forward
- The small end rollers of the 8-lb uniform slender bar (length = 4 ft) are constrained to move in the slots, which lie in the vertical plane. At the instant when Angle theta = 30°, the velocity of roller A is 13 ft/s down the vertical slot. Determine the angular acceleration of the bar, the acceleration of mass center G and the reactions of points A and B, under the action ofthe 6-lb force P. Neglect the friction and the mass of the small rollers.arrow_forwardIn the figure, rod AB has a mass of 10 kg, and must slide within the slots as shown. If the spring is unstretched when θ = 0°, determine the angular velocity of the bar when it reaches that angle after being released from θ = 30°.arrow_forwardThe 18-kg rod AB is pin-connected at A and subjected to a couple moment of M =15 N- m The rod is released from rest when the spring is unstretched at 0 = 30°. As the rod rotates, the spring always remains horizontal, because of the roller support at C. (Figure 1) Determine the rod' s angular velocity, measured clockwise, at the instant 0 = 60°. Express your answer using three significant figures. Enter positive value if the angular velocity is clockwise and negative value if the angular velocity is counterclockwise. vec rad/s k = 40 N/m 0.75 m M = 15 N- marrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License