ENGR.MECH.:DYNAMICS-PACKAGE
14th Edition
ISBN: 9780134267463
Author: HIBBELER
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 19.4, Problem 6RP
Spool B is at rest and spool A is rotating at 6 rad/s when the slack in the cord connecting them is taken up If the cad does not stretch, determine the angular velocity of each spool immediately after the cord is jerked light. The spools A and B have weights and radii of gyration WA = 30 lb, kA = 0.8 ft, WB = 15 lb, kB = 0.6 ft, respectively.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
In the helicopter shown; a vertical tail propeller is used to pre-
vent rotation of the cab as the speed of the main blades is
changed. Assuming that the tail propeller is not operating
determine the final angular velocity of the cab after the speed
of the main blades has been changed from I80 to 240 rpm. (The
speed of the main blades is measured relative to the cab, and
the cab has a centroidal moment of inertia of 650 lb.ft.s2.
Each of the four main blades is assumed to be a slender rod 14 ft weighing 55 lb.)
The differential pulley C, which rotates as a unit, has a mass of 14.1 kg, an inner radius of 75 mm, an outer radius of 150 mm, and a radius of gyration of 100 mm about its stationary centre of gravity at O. Each cylinder (A and B) has a mass of 18.6 kg. At the instant shown, the light cables do not slip and cylinder A has a velocity of vA= 2.5 m/s (downwards). The motion occurs in a vertical plane. What is the total kinetic energy of the system at this instant? Choose the correct answer.
a) 78.4 Joule
b) 87.6 Joule
c) 73.8 Joule
d) 55.3 Joule
e) 92.2 Joule
The rod AB has a mass of 20 kg，the mass of the piston A and B are both 5kg. Piston B is attached to a spring of constant k = 1200 N/m. The spring is un-stretched when θ = 0. If the rod is released from rest whenθ = 45°
Please find÷
(1) the moment inertia of the rod AB about its mass center G
(2)The angular velocity of rod AB at θ = 0°
(3）the velocity of piston A at θ = 0°
(4) the velocity of Piston B at θ = 0°
(hint: regard the piston A, B, rod as a system, during the motion, except the spring, the weight of rod AB, the weight of pistonB also does work). g = 9.8 m/s2
Chapter 19 Solutions
ENGR.MECH.:DYNAMICS-PACKAGE
Ch. 19.2 - Determine the angular momentum of the 100-kg disk...Ch. 19.2 - Determine the angular impulse about point O for t...Ch. 19.2 - If it is subjected to a couple moment of M = (3t2)...Ch. 19.2 - The 300-kg wheel has a rad1us of gyration about...Ch. 19.2 - If rod OA of negligible mass is subjected lo the...Ch. 19.2 - Gears A and B of mass 10 kg and 50 kg have radii...Ch. 19.2 - The 50-kg spool is subjected to a horizontal force...Ch. 19.2 - The reel has a weight of 150 lb and a radius of...Ch. 19.2 - The rigid body (slab) has a mass m and rotates...Ch. 19.2 - At a given Instant, the body has a linear momentum...
Ch. 19.2 - Show that if a slab is rotating about a fixed axis...Ch. 19.2 - The 40-kg disk is rotating at = 100 rad/s. When...Ch. 19.2 - The Impact wrench cons1sts of a slender 1-kg rod...Ch. 19.2 - The airplane is traveling in a straight line with...Ch. 19.2 - The double pulley consists of two wheels which are...Ch. 19.2 - The assembly weighs 10 lb and has a radius of...Ch. 19.2 - The disk has a weight of 10 lb and is pinned at...Ch. 19.2 - The 30-kg gear A has a radius of gyration about...Ch. 19.2 - Determine the angular velocity of the pulley when...Ch. 19.2 - The 40-kg roll of paper rests along the wall where...Ch. 19.2 - The slender rod has a mass m and is suspended at...Ch. 19.2 - The rod of length L and mass m lies on a smooth...Ch. 19.2 - A 4-kg disk A is mounted on arm BC. which has a...Ch. 19.2 - The frame of a tandem drum roller has a weight of...Ch. 19.2 - The 100-lb wheel has a radius of gyration of kG =...Ch. 19.2 - The 4-kg slender rod rests on a smooth floor If it...Ch. 19.2 - The double pulley consists of two wheels which are...Ch. 19.2 - The 100-kg spool is resting on the inclined...Ch. 19.2 - The spool has a weight of 30 lb and a radius of...Ch. 19.2 - The two gears A and B have weights and radii of...Ch. 19.2 - The hoop (thin ring) has a mass of 5 kg and is...Ch. 19.2 - The 30-kg gear is subjected to a force of P =...Ch. 19.2 - The 30-lb flywheel A has a radius of gyration...Ch. 19.2 - If the shaft is subjected to a torque of M = (...Ch. 19.2 - The double pulley consists of two wheels which are...Ch. 19.2 - The crate has a mass mc. Determine the constant...Ch. 19.4 - The turntable T of a record player has a mass of...Ch. 19.4 - The 10-g bullet having a velocity of 800 m/s is...Ch. 19.4 - The 10-g bullet having a velocity of 800 m/s is...Ch. 19.4 - The circular disk has a mass m and is suspended at...Ch. 19.4 - The 80-kg man is holding two dumbbells while...Ch. 19.4 - The platform swing consists of a 200-lb flat plate...Ch. 19.4 - The 2-kg rod ACB supports the two 4-kg disks at...Ch. 19.4 - The satellite has a mass of 200 kg and a radius of...Ch. 19.4 - Disk A has a weight of 20 lb. An inextensible...Ch. 19.4 - The plank has a weight of 30 lb, center of gravity...Ch. 19.4 - The 12-kg rod AB is pinned to the 40-kg disk. If...Ch. 19.4 - A thin rod of mass m has an angular velocity o...Ch. 19.4 - Tests of impact on the fixed crash dummy are...Ch. 19.4 - The vertical shaft is rotating with an angular...Ch. 19.4 - The mass center of the 3-lb ball h3s a velocity of...Ch. 19.4 - Prob. 44PCh. 19.4 - The 10-lb block is sliding on the smooth surface...Ch. 19.4 - Determine the height hat which a billiard ball of...Ch. 19.4 - The pendulum consists of a 15-kg solid ball and...Ch. 19.4 - The 4-lb rod AB is hanging in the vertical...Ch. 19.4 - Determine the largest angular velocity 1 the disk...Ch. 19.4 - The solid ball of mass m is dropped with a...Ch. 19.4 - The wheel has a mass of 50 kg and a radius of...Ch. 19.4 - The wheel has a mass of 50 kg and a radius of...Ch. 19.4 - The rod of mass m and length L is released from...Ch. 19.4 - Prob. 55PCh. 19.4 - A ball having a mass of 8 kg and initial speed of...Ch. 19.4 - A solid ball with a mass m is thrown on the ground...Ch. 19.4 - The pendulum consists of a 10-lb solid ball and...Ch. 19.4 - The cable is subjected to a force of P = (10t2)...Ch. 19.4 - The space capsule has a mass of 1200 kg and a...Ch. 19.4 - The tire has a mass of 9 kg and a rad1us of...Ch. 19.4 - The wheel having a mass of 100 kg and a radius of...Ch. 19.4 - The spool has a weight of 30 lb and a radius of...Ch. 19.4 - Spool B is at rest and spool A is rotating at 6...Ch. 19.4 - A thin disk of mass m has an angular velocity 1...Ch. 19.4 - Prob. 8RP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The 100-kgkg spool is resting on the inclined surface for which the coefficient of kinetic friction is μkμkmu = 0.1. The radius of gyration about the mass center is kGkGk_G = 0.26 mm. Determine the angular velocity of the spool, measured clockwise, when ttt = 6 ss after it is released from rest.arrow_forwardThe pendulum has a mass of 8.8 kg, a centre of gravity at G, and a radius of gyration of 0.31 m about the fixed pin support at O. At what position (in degrees) must the pendulum by released from rest so that its angular acceleration is 18.6 (clockwise) at that instant? Take = 0.25 m. The motion occurs in a vertical plane and friction is negligible. Choose the correct answer. 43.2 36.7 34.6 48.4 41.1arrow_forwardThe turbine rotor of a ship has a mass of 2.2 tonnes and CO1(L2) rotates at 1800 rpm clockwise when viewed from the aft The radius of gyration of the rotor is 320 mm. Determine the gyroscopic couple and its effect when (a) The ship turns right at a radius of 250 m with a speed of 25 km/h. (b) The ship pitches with the bow rising at an angular velocity of 0.8 rad/s (c) The ship rolls at an angular velocity of 0.1 rad/s.arrow_forward
- A cable is wrapped around the spool’s center hub. The mass of the spool is m= 100 kg, the radius r1 = 0.4 m, r2 =0.6 m, and the radius of gyration is kG = 0.3 m. A horizontal force P = 10 N is applied to the cord. The spool is initially at rest and rolls without slipping. (1) The angular impulse of the spool about point A after 2 second, =________(N·m·s) (two decimal places)arrow_forwardThe two gears A and B have weights and radii of gyration of WA = 15 lb , kA = 0.5 ft and WB = 15 lb , kB = 0.35 ft, respectively. A motor transmits a couple moment to gear B of M=2(1−e−0.5t)lb⋅ft, where t is in seconds. Determine the angular velocity of gear A in t = 5 s , measured counterclockwise, starting from rest.arrow_forwardThe 100-kg spool is resting on the inclined surface for which the coefficient of kinetic friction is μk = 0.11. The radius of gyration about the mass center is kG = 0.26 m Determine the angular velocity of the spool, measured clockwise, when t = 7 s after it is released from rest.arrow_forward
- The 30 kg rod is released from rest when theta =0°. The spring is unstretched when theta = 0°. Find the angular velocity of the rod when theta = 30° and length of stretched spring is 1 m.arrow_forwardThe slotted circular disk whose mass is 4.9 kg has a radius of gyration about O of 230 mm. The disk carries the four steel balls, each of mass 0.17 kg and located as shown, and rotates freely about a vertical axis through O with an angular speed of 164 rev/min. Each of the small balls is held in place by a latching device not shown. If the balls are released while the disk is rotating and come to rest relative to the disk at the outer ends of the slots, compute the new angular speed N of the disk. Also find the magnitude |ΔE| of the energy loss due to the impact of the balls with the ends of the slots. Neglect the diameter of the balls and discuss this approximation.arrow_forwardAssuming that the tail propeller in Prob. 17.84 is operating and that the angular velocity of the cab remains zero, determine the final horizontal velocity of the cab when the speed of the main blades is changed from 180 to 240 rpm. The cab weighs 1250 lb and is initially at rest. Also, determine the force exerted by the tail propeller if the change in speed takes place uniformly in 12 s.arrow_forward
- The 25-kg cylinder A is free to slide along rod BC. When the cylinder is at x=0, the 46-kg circular disk D is rotating with an angular velocity of 4.8 rad/s. (Figure 1) If the cylinder is given a slight push, determine the angular velocity of the disk when the cylinder strikes B at x=600mm. Neglect the mass of the brackets and the smooth rod.arrow_forwardTwo homogeneous rods BC and CD of mass 2 kg/m are welded together to form an L-shaped member and pin jointed at B. At the instant shown, the spring of stiffness k = 150 N/m is stretched to 0.5 m while the resisting couple M = 5 Nm. If the mechanism is released from rest, determine the angular velocity of member BCD when CD is vertical after member BCD rotates counterclockwise.arrow_forwardA cable is wrapped around the spool’s center hub. The mass of the spool is m= 100 kg, the radius r1 = 0.4 m, r2 =0.6 m, and the radius of gyration is kG = 0.3 m. A horizontal force P = 10 N is applied to the cord. The spool is initially at rest and rolls without slipping. (3) The angular velocity after 2 seconds is __________rad/s (two decimal places)arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license