Principles Of Highway Engineering And Traffic Analysis
7th Edition
ISBN: 9781119493969
Author: Mannering, Fred L., WASHBURN, Scott S.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 2, Problem 6P
To determine
The maximum grade that a car could ascend on a paved surface, while the engine is developing maximum torque.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Consider a truck with a maximum power of 500 kW and a frontal area of 11 m2 . The maximum speed the truck can maintain on an incline with a grade of 2.5% is 15 m/s. Assume air density ρ = 1.225 kg/m3 and the “drag coefficient” is CD = 0.75. What is the mass of the truck?
In an ore-mixing operation, a bucket full of ore is suspended from a travelling crane which moves along a stationary bridge. The bucket is to swing no more than 10 ft horizontally when the crane is brought to a sudden stop. Determine the maximum allowable speed v in ft / s of the crane .
A civil engineer's preliminary design for a freeway off-ramp is circular with radius R = 75m. What is the maximum speed (kph) at which vehicles will reach the ramp without losing traction of he believes that the coefficient of static friction between tires and road is least 0.35?
Solve correctly and explain! I'll rate!
Chapter 2 Solutions
Principles Of Highway Engineering And Traffic Analysis
Ch. 2 - Prob. 1PCh. 2 - Prob. 2PCh. 2 - Prob. 3PCh. 2 - Prob. 4PCh. 2 - Prob. 5PCh. 2 - Prob. 6PCh. 2 - Prob. 7PCh. 2 - Prob. 8PCh. 2 - Prob. 9PCh. 2 - Prob. 10P
Ch. 2 - Prob. 11PCh. 2 - Prob. 12PCh. 2 - Prob. 13PCh. 2 - Prob. 14PCh. 2 - Prob. 15PCh. 2 - Prob. 16PCh. 2 - Prob. 17PCh. 2 - Prob. 18PCh. 2 - Prob. 19PCh. 2 - Prob. 20PCh. 2 - Prob. 21PCh. 2 - Prob. 22PCh. 2 - Prob. 23PCh. 2 - Prob. 24PCh. 2 - Prob. 25PCh. 2 - Prob. 26PCh. 2 - Prob. 27PCh. 2 - Prob. 28PCh. 2 - Prob. 29PCh. 2 - Prob. 30PCh. 2 - Prob. 31PCh. 2 - Prob. 32PCh. 2 - Prob. 33PCh. 2 - Prob. 34PCh. 2 - Prob. 35PCh. 2 - Prob. 36PCh. 2 - Prob. 37PCh. 2 - Prob. 38PCh. 2 - Prob. 39PCh. 2 - Prob. 40P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- A car having a weight of 40 kN is moving at a certain speed around the curve. Assuming no lateral pressure between the tire and the pavement, compute for the following if the centrifugal ratio is 0.30. (a) Compute the force that will tend to pull the car away from the center of the curve. (b) If the degree of the curve is 4 degrees, determine the maximum speed that the car could move around the curve. (c) Compute for the embankment angle to be provided for this speed if the skid resistance is 0.12.arrow_forwardA car having a weight of 40kN 5 points is moving at a certain speed around the curve. Assuming no lateralpressure between the tire and pavement and considering a centrifugal ratio of 0.30, Compute the force in kN that will tend to pull the car away from the center of the curve. assume f = 1.0 for fatigue design.arrow_forwardCivil Engineering Q)If the horse power 107.1 hp produced by a passenger car traveling at a speed of 84 mi/h on a straight road of 6% grade with a smooth pavement.(Find the rolling / curve/ air/ grade)resistance ?(Note : Assume the cross-sectional area of the car is 45 ft2)arrow_forward
- A 15.6-kN vehicle (Cd = 0.40, Af = 2.4 m2, rho = 1.2256 kg/m3) is driven on a surface with a coefficient of adhesion of 0.5, and the coefficient of rolling friction is approximated as 0.015 for all speeds. Assuming minimum theoretical stopping distances, if the vehicle comes to a stop 76 m after brake application on a level surface and has a braking efficiency of 0.78, what was its initial speed (a) if aerodynamic resistance is considered and (b) if aerodynamic resistance is ignored?arrow_forwardEstimate the power requires to accelerate a 1350 kg vehicle traveling at 48 kph up a 5% grade at the rate of 1.8 m/sec². The roadway has a straight alignment and a badly broken and patched asphalt surface. Rolling resistance of vehicle is 167 N/metric-ton, Air density = 1.2 kg/m³, and Aerodynamic drag coefficient = 1.3. Express power in watts using the formula P = RV. Use the formula for:arrow_forwardA truck tractor unit, operating in its fourth gear range and at its full-rated rpm., is observed to maintain a steady speed of 7.5 mph, when operating under the conditions described herein. Ambient air temperature is 60°F. Altitude is sea level. The tractor is climbing a uniform 5.5% slope with a rolling resistance of 55 lb per ton, and it is towing a pneumatic-tired trailer loaded with fill material. The single-axle tractor has an operating weight of 66,000 lb. The loaded trailer has a weight of 48,000 lb. The weight distribution for the combined tractor trailer unit is 55% to the truck drive axle and 45% to the trailer rear axle. a. The manufacturer, for the environmental conditions just described rates the tractive effort of the new tractor at 330 rimpull horsepower. What percentage of this rated rimpull hp does the tractor develop? i. In performing your calculations, it will be acceptable to assume that the component of weight normal to the traveling surface is equal to the…arrow_forward
- The coefficients of friction between the load and the flat-bed trailer shown are 0.35 (static) and 0.30 (kinetic). Knowing that the speed of the rig is 72 km/h , at what deceleration in m/s^ 2 must the truck apply for a shortest distance in which the rig can be brought to a stop if the load is not to shift.arrow_forwardA vehicle weighing a 50 kN is moving at a constant speed around a circular curve. Neglecting the friction between the tires and the pavement and the centrifugal ratio (the ratio of the centrifugal force experience by the vehicle on the curve to its own weight) is 0.30. The degree of the curve is 5 degrees.a. Calculate the centrifugal force.b. Calculate the maximum speed the vehicle could move around the curve (in kph)c. If the skid resistance is 0.15, calculate the maximum super elevation that can be provided for the speed calculated from b.arrow_forward13.How much horsepower must be delivered to the wheels of a 10,000 lb loaded truck to maintain a constant speed of 55 mph on a +5% grade? Assume the following: Aerodynamic drag coefficient = 0.4 Vehicle’s frontal cross-sectional area = 100 ft2arrow_forward
- A truck weighing 35 tons is traveling at 32 km/h round a curve track of 43 m radius. If thecenter of gravity of the truck is 2.3 m above the rails, calculate the vertical reaction of eachwheel if the wheel distance is 1.7 m apart Additionally, if the track is banked at 13 degree and thecoefficient of friction is 0.4, and find the truck's maximum speed.arrow_forwardA vehicle moving at a speed at a speed of 90 kph along an incline surface having aslope of 5%. If the coefficient of friction is 0.20, determine the braking distance.arrow_forwardA 2500-lb passenger vehicle originally traveling on a straight and level road gets onto a section of the road with a horizontal curve of radius = 850 ft. If the vehicle was originally traveling at 55 mi/h, determine (a) the additional horsepower on the curve the vehicle must produce to maintain the original speed, (b) the total resistance force on the vehicle as it traverses the horizontal curve, and (c) the total horsepower. Assume that the vehicle is traveling at sea level and has a front cross-sectional area of 30 ft2. Show your step by step solutions.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Structural Analysis (10th Edition)Civil EngineeringISBN:9780134610672Author:Russell C. HibbelerPublisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Fundamentals of Structural AnalysisCivil EngineeringISBN:9780073398006Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel LanningPublisher:McGraw-Hill Education
Traffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage Learning
Structural Analysis (10th Edition)
Civil Engineering
ISBN:9780134610672
Author:Russell C. Hibbeler
Publisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Fundamentals of Structural Analysis
Civil Engineering
ISBN:9780073398006
Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning
Publisher:McGraw-Hill Education
Traffic and Highway Engineering
Civil Engineering
ISBN:9781305156241
Author:Garber, Nicholas J.
Publisher:Cengage Learning