EBK NUMERICAL METHODS FOR ENGINEERS
7th Edition
ISBN: 9780100254145
Author: Chapra
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 21, Problem 18P
Develop a user-friendly computer program for integratingunequally spaced data based on Fig. 21.15b. Test it by duplicating the computation from Example 21.8.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
4. Using the method of Least Squares, determine to 6-decimal place the necessary values of the
coefficient C1 and C2 in the equation from the given data points.
1
y =
C, + C2x
A
C
2.07
8.60
14.42
15.8
Where:
ABCDEF is your student number.
Example, if your student number is 484321.
A = 4
B = 8
C = 4
D = 3
5. Using the same data points given in problem 4, solve for the Newton's Interpolating
Polynomials.
Use bisection to determine the drag coefficient needed so that an 80-kg parachutist has a velocity of 36 m/s after 4 s of free fall. Note: The acceleration of gravity is 9.81 m/s2 . Start with initial guesses of xl = 0.1 and xu = 0.2 and iterate until the approximate relative error falls below 2%.
Find the three unknown on this problems using
Elimination Method and Cramer's Rule. Attach your
solutions and indicate your final answer.
Problem 1.
7z 5y
3z
16
%3D
3z
5y + 2z
-8
%3D
5z + 3y
7z
= 0
Problem 2.
4x-2y+3z 1
*+3y-4z -7
3x+ y+2z 5
Chapter 21 Solutions
EBK NUMERICAL METHODS FOR ENGINEERS
Ch. 21 - 21.1 Evaluate the following...Ch. 21 - 21.2 Evaluate the following...Ch. 21 - Evaluate the following integral: 24(1x4x3+2x5)dx...Ch. 21 - Integrate the following function analytically and...Ch. 21 - 21.5 Integrate the following function both...Ch. 21 - Integrate the following function both analytically...Ch. 21 - 21.7 Integrate the following function both...Ch. 21 - 21.8 Integrate the following function both...Ch. 21 - 21.9 Suppose that the upward force of air...Ch. 21 - 21.10 Evaluate the integral of the following...
Ch. 21 - Prob. 11PCh. 21 - 21.12 Determine the mean value of the...Ch. 21 - 21.13 The function can be used to generate the...Ch. 21 - Evaluate the following double integral:...Ch. 21 - Evaluate the following triple integral...Ch. 21 - Develop a user-friendly computer program for the...Ch. 21 - Develop a user-friendly computer program for the...Ch. 21 - Develop a user-friendly computer program for...Ch. 21 - The following data was collected for a...Ch. 21 - 21.20 The outflow concentration from a reactor is...Ch. 21 - 21.21 An 11-m beam is subjected to a load, and the...Ch. 21 - The work produced by a constant temperature,...Ch. 21 - Determine the distance traveled for the following...Ch. 21 - 21.24 The total mass of a variable density rod is...Ch. 21 - 21.25 A transportation engineering study requires...Ch. 21 - Determine the average value for the data in Fig....
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
|4.2| = ?
Basic Technical Mathematics
(a) Show that (x) = x2 is an explicit solution to xdydx = 2y on the interval (, ). (b) Show that (x) = ex x is...
Fundamentals of Differential Equations (9th Edition)
Analytic Functions. Find fz=ux,y+ivx,y with u or v as given. Check by the Cauchy Reimann equations for analyti...
Advanced Engineering Mathematics
Find how many SDs above the mean price would be predicted to cost.
Intro Stats, Books a la Carte Edition (5th Edition)
In the following exercises, multiply the monomials. 138. (14d5)(36d2)
Elementary Algebra
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 1. The following transportation problem of cost matrix is: Destination Supply A 7. 10 6. 80 15 Demand 75 20 50 Sources Requirement: Is it what type of transportation problem? Discuss the other types of it. The penalty costs for not satisfying demand at the warehouses D, E, and F are TK. 5, 3, and 2 per unk respectively. Determine minimum transportation cost by using Lest Cost Method (LCM)arrow_forward33.2 solve using MATLAB. do not use syms.arrow_forwarda) b) c) Use composite Simpson's rule to estimate xe*dx with n=4. Subsequently, find the absolute error. dy dx Given 3y + 2x, where y(0) = 1 and h = 0.2. Approximate the solution for the differential equation for one iteration only by using Runge Kutta method of order two. Set up the Gauss-Siedel iterative equations the following linear system: 6x₁-3x₂ = 2 -x₁ + 3x₂ + x3 =1 x₂ + 4x₂ = 3 (Do not solve)arrow_forward
- The parts department of a large automobile dealership has a counter used exclusively for mechanics’ requests for parts. The time between requests can be modeled by a negative exponential distribution that has a mean of five minutes. A clerk can handle requests at a rate of 15 per hour, andthis can be modeled by a Poisson distribution that has a mean of 15. Suppose there are two clerksat the counter.a. On average, how many mechanics would be at the counter, including those being served?arrow_forwardThe following data describe the dissolved oxygen concentration at sea level for freshwater as a function of temperature. In the light of these data, the amount of dissolved oxygen at a temperature of 18 degreesa) Estimate with using the linear interpolation polynomial.b) Estimate using the 2nd order Lagrangian interpolation polynomial.arrow_forwardHello Sir.Good night.Permission, i have a question in my homework related numerical methods lesson. The following bellow is question. Please advice. Thank you so much Regards,Irfan Mention the types of problems that exist in the field of engineering, especially mechanical engineering that can be solved by the linear regression methodarrow_forward
- for 0 < x < 1 у (х) %3 Зех - 5 Use the Bisection Method to look for a root of the equation. Begin with values of x = 0.5 and = 0.6. Complete three iterations of the method by filling out the table below. Show your %3D calculations. Xc f(x,) f (x.) Iterations Xr 1 0.5 0.8arrow_forwardRead the questions carefully and answer with complete solution and units. Use the steam tables provided and use 4 decimal places for solving. Final answers shown are in 2 decimal places. Draw the T-S diagrams properly with respect to the saturation line A steam power plant uses the ideal Reheat-Regenerative Rankine cycle where the steam enters the high-pressure turbine at 4 MPa and 300C. It partially expands to 600 kPa where some steam is extracted for feedwater heating while the rest is reheated to the same temperature. After expanding again, it enters the condenser at 10 kPa. Sketch the schematic diagram and the TS diagram with labeled points, and solve for mass taken for feedwater heating, Qa, Qr, Wt, Wp, Wnet, thermal efficiency, and Steam rate. Neglect the condensate pump work. 20.01%, 2667.841,1715.52,955.97, 3.74,952.32¹,3 35.69%, 3.78- kg kg kg kg kWh Iarrow_forwardFour technicians are required to do four different jobs. Estimates of time to complete every job as provided by the technicians are as below: Technician Hours to Complete Job Job 1 Job 2 Job 3 Job 4 A 20 36 31 27 В 24 34 45 22 45 38 18 37 40 35 28 Assign the jobs to technicians to minimize the total work-time. State the steps taken in the algorithm used.arrow_forward
- 3. Using the trial function u¹(x) = a sin(x) and weighting function w¹(x) = b sin(x) find an approximate solution to the following boundary value problems by determining the value of coefficient a. For each one, also find the exact solution using Matlab and plot the exact and approximate solutions. (One point each for: (i) finding a, (ii) finding the exact solution, and (iii) plotting the solution) a. (U₁xx -2 = 0 u(0) = 0 u(1) = 0 b. Modify the trial function and find an approximation for the following boundary value problem. (Hint: you will need to add an extra term to the function to make it satisfy the boundary conditions.) (U₁xx-2 = 0 u(0) = 1 u(1) = 0arrow_forward3. Using the trial function uh(x) = a sin(x) and weighting function wh(x) = b sin(x) find an approximate solution to the following boundary value problems by determining the value of coefficient a. For each one, also find the exact solution using Matlab and plot the exact and approximate solutions. (One point each for: (i) finding a, (ii) finding the exact solution, and (iii) plotting the solution) a. (U₁xx - 2 = 0 u(0) = 0 u(1) = 0 b. Modify the trial function and find an approximation for the following boundary value problem. (Hint: you will need to add an extra term to the function to make it satisfy the boundary conditions.) (U₁xx - 2 = 0 u(0) = 1 u(1) = 0arrow_forwardFour technicians are required to do four different jobs. Estimates of time to complete every job as provided by the technicians are as below: Technician Hours to Complete Job Job 1 Job 2 Job 3 Job 4 A 20 36 31 27 В 24 34 45 22 C 45 38 18 37 40 35 28 Assign the jobs to technicians to minimize the total work-time. State the steps taken in the algorithm used.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Graph Theory: Euler Paths and Euler Circuits; Author: Mathispower4u;https://www.youtube.com/watch?v=5M-m62qTR-s;License: Standard YouTube License, CC-BY
WALK,TRIAL,CIRCUIT,PATH,CYCLE IN GRAPH THEORY; Author: DIVVELA SRINIVASA RAO;https://www.youtube.com/watch?v=iYVltZtnAik;License: Standard YouTube License, CC-BY