Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
6th Edition
ISBN: 9780135257272
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 21, Problem 8CQ
A customer complains that the heater works sometimes, but sometimes only cold air comes out while driving. Technician A says that the water pump is defective. Technician B says that the cooling system could be low on coolant. Which technician is correct?
- a. Technician A only
- b. Technician B only
- c. Both Technicians A and B
- d. Defective pressure cap
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Match the correct advantage with the fluid power system.
Technician A says that excessively high pressure from an electric fuel pump can be caused by a faulty pressure regulator. Technician B says that the typical problem may be an obstructed return line. Who is correct?
Technician A says that suction lines become verywarm during A/C operation. Technician B says that discharge lines connect the compressor tothe condenser. Who is correct?
Chapter 21 Solutions
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Ch. 21 - What is normal operating coolant temperature?Ch. 21 - Explain the flow of coolant through the engine and...Ch. 21 - Why is a cooling system pressurized?Ch. 21 - Describe how to diagnose a heater problem.Ch. 21 - What are 10 common causes of overheating?Ch. 21 - What diagnostic trouble code (DTC) could be set if...Ch. 21 - Prob. 2CQCh. 21 - What type of pump is a water pump? a. Positive...Ch. 21 - Water pumps __________. a. only work at idle and...Ch. 21 - Which statement is true about thermostats? a. The...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
A nozzle at A discharges water with an initial velocity of 36 ft/s at an angle with the horizontal. Determine ...
Vector Mechanics for Engineers: Dynamics
Determine the velocity of block D if end A of the rope is pulled down with a speed of vA = 3 m/s.
Engineering Mechanics: Dynamics (14th Edition)
The moment of inertia Iy for the slender rod in terms of the rod’s total mass m .
Engineering Mechanics: Statics & Dynamics (14th Edition)
Locate the centroid of the area. Prob. 9-17
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
A number of common substances are
Some of these materials exhibit characteristics of both solid and fluid beha...
Fox and McDonald's Introduction to Fluid Mechanics
17–1C A high-speed aircraft is cruising in still air. How does the temperature of air at the nose of the aircra...
Thermodynamics: An Engineering Approach
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Briefly describe the function of a non-short-cycling, or "one-time," automatic pumpdown system.arrow_forwardTechnician A says that some refrigerant leaks can also be traced to pinholes in the evaporator caused by acid, which forms when water and refrigerant mix. Technician B says that leaks are most often found at the compressor hose connections and at the various fittings and joints in the system. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forward1-While refilling an 8-quart (7.57 L) system with coolant: Technician A initially puts in 4 quarts (3.78 L) of straight coolant and tops it off with water. Technician B fills the system with the correct mixture, tightens the radiator cap, and then checks for leaks. Who is correct? 2-While checking for conditions that might cause coolant electrolysis: Technician A places the positive lead of a voltmeter into the coolant and connects the negative lead to a ground. Technician B checks for the presence of voltage in the coolant with the ignition off. Who is correct? 3-Technician A says that if the PCV valve or connecting hoses become clogged, excessive pressure will develop in the crankcase and can cause oil leaks. Technician B says that if the PCV valve or connecting hoses become clogged, oil may be pushed into the air cleaner or cause it to be drawn into the intake manifold. Who is correct? 4-While bleeding air from a cooling system: Technician A loosens a heater hose at its highest…arrow_forward
- Technician A says PVE refrigerant oil is com monly recommended for electric A/C compres sors. Technician B says PAG refrigerant oil can be used in many electric A / C compressors . Who is correct ?arrow_forwardWhat can be done to get water out from under the oil level in a compressor?arrow_forwardDescribe the operation of the exhaust and fresh-air control.arrow_forward
- Trying to stop escaping liquid refrigerant with your hands will result in ______.arrow_forwardWhy is a plastic or metal restrictor placed in either the end of the vent pipe or in the vapor-vent hose on some vehicles?arrow_forwardAdvantages in using a dual cylinder water pumping system using scotch yoke mechanismarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
The Refrigeration Cycle Explained - The Four Major Components; Author: HVAC Know It All;https://www.youtube.com/watch?v=zfciSvOZDUY;License: Standard YouTube License, CC-BY