Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
5th Edition
ISBN: 9780133994612
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 22, Problem 8CQ
The purpose of the oil fitter bypass valve is to ___________.
- a. allow oil to bypass the filter if the filter becomes clogged
- b. keep the oil from draining out of the filter when the engine is off and the oil pressure drops to zero
- c. allow oil to bypass the oil filter when the oil is hot, to help cool the oil
- d. Both a and b
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Technician A says that the engine oil drain
plug typically needs to be replaced with a
new one at each oil change. Technician B
says that engine oil drain plugs must be
tightened with a torque wrench when they
are installed. Who is correct?
Select one:
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
Which type of oil filter uses an anti drain back valve to prevent it from emptying of oil when the engine is shut off
When installing a spin-on oil filter, failure to
lube the O-ring will:
Select one:
a. lead to double gasketing.
b. damage the threads on the adapter.
C. cause it to bind and roll out of the
oil filter groove.
d. damage the threads on the adapter.
Chapter 22 Solutions
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Ch. 22 - What property of oil does the SAE ratings reflect?Ch. 22 - Prob. 2RQCh. 22 - Why is the oil filter bypassed when the engine oil...Ch. 22 - What are the steps in performing an oil change?Ch. 22 - The W in SAE 5W-20 means ___________. a. weight b....Ch. 22 - Oil change intervals as specified by the vehicle...Ch. 22 - Most conventional (mineral) oil is made from what...Ch. 22 - Which rating is the ACEA rating specified for use...Ch. 22 - Prob. 5CQCh. 22 - Technician A says that some vehicle manufacturers...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Find the change in length of side AB.
Mechanics of Materials, 7th Edition
Assume the following vectors are already defined: V1=[302]V2=[214]V3=[5131]V4=[0.50.10.20.2] For each of the fo...
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
A biological fluid moves at a flow rate of m=0.02kg/s through a coiled, thin-walled, 5-mm-diameter tube submerg...
Fundamentals of Heat and Mass Transfer
What is the importance of modeling in engineering? How are the mathematical models for engineering processes pr...
HEAT+MASS TRANSFER:FUND.+APPL.
For the beam loading of Figure P334, draw the complete shearing force and bending moment diagrams, and determin...
Machine Elements in Mechanical Design (6th Edition) (What's New in Trades & Technology)
19.8 Calculate the allowable tensile load for the connection shown. The plates are ASTM A36 steel and the weld ...
Applied Statics and Strength of Materials (6th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that broken engine mounts can cause the fan to hit the shroud. Technician B says that missing or broken air dams can cause an engine to overheat. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardMatch the correct advantage with the fluid power system.arrow_forwardThe amount of fluid allowed to enter the cylinder can be controlled, this is done with the use of a/an ______________ control valve.arrow_forward
- Technician A says that a two-stroke oil injection system uses a gravity-fed pressure system. Technician B says that a reservoir is not needed to store injection oil. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardIf oil pressure is higher than specifications: Select one: a. there may be excessive clearance in the engine bearings. b. the oil pump may be worn. c. the engine is noisy. d. the oil pressure regulator might be stickingarrow_forwardCarbon deposits on the intake valve or seat may cause the valve not to close properly. Tech a says that the flywheel will be harder to spin when starting the engine. Tech b says that the engine will loose power. Who is correct?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license