Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
5th Edition
ISBN: 9780133994612
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 22, Problem 6CQ
Technician A says that some vehicle manufacturers recommend an ILSAC grade be used in the engine. Technician B says that an oil with the specified API rating and SAE viscosity rating should be used in an engine. Which technician is correct?
- a. Technician A only
- b. Technician B only
- c. Both Technicians A and B
- d. Neither Technician A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Technician A says that if the oil pressure
shows low on the vehicle's gauge, engine
oil pressure should be verified using a
manual test gauge. Technician B says that
if a vehicle's oil pressure gauge reads too
high, engine oil pressure should be
verified using a manual test gauge. Who is
correct?
Select one:
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
When performing an engine oil level
check, if additional oil is needed, estimate
the amount by checking the emissions
standards guide to the dipstick markings.
Select one:
True
False
Given two oil According to the standard by Society Automotive
Engineers the oil , by comparing the 5W-30 with the 10W-30,
a. The 5W-30 has lower viscosity than 10W-30 at low
temperature.
O b. The 5W-30 has higher viscosity at the high temperature.
c.
Both of the oils are suitable for cold weather
O d. All of the above are true.
Chapter 22 Solutions
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Ch. 22 - What property of oil does the SAE ratings reflect?Ch. 22 - Prob. 2RQCh. 22 - Why is the oil filter bypassed when the engine oil...Ch. 22 - What are the steps in performing an oil change?Ch. 22 - The W in SAE 5W-20 means ___________. a. weight b....Ch. 22 - Oil change intervals as specified by the vehicle...Ch. 22 - Most conventional (mineral) oil is made from what...Ch. 22 - Which rating is the ACEA rating specified for use...Ch. 22 - Prob. 5CQCh. 22 - Technician A says that some vehicle manufacturers...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Three rigid bodies, 2,3, and 4, are connected by four springs as shown in the figure. A horizontal force of 1,0...
Introduction To Finite Element Analysis And Design
A nozzle at A discharges water with an initial velocity of 36 ft/s at an angle with the horizontal. Determine ...
Vector Mechanics for Engineers: Dynamics
What is the importance of modeling in engineering? How are the mathematical models for engineering processes pr...
HEAT+MASS TRANSFER:FUND.+APPL.
Convert the following quantities from English to SI units: a. 98 Btu/(hr-ft-F) b. 0.24 Btu/(lbm-F) C. 0.04 Ibm/...
Heating Ventilating and Air Conditioning: Analysis and Design
Repeat Problem 4-6 except solve by the vector loop method.
DESIGN OF MACHINERY
17–1C A high-speed aircraft is cruising in still air. How does the temperature of air at the nose of the aircra...
Thermodynamics: An Engineering Approach
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A reddish-colored oil is discovered to be leaking during an engine oil change and inspection: Technician A says it may be from a leak in the cooling system. Technician B says it may be leaking transmission fluid. Who is correct?arrow_forwardTechnician A says that when draining the engine oil, the engine should be fully cold for best results. Technician B says that the engine should be running when checking the engine oil level. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardList five different types of oil rating systemsarrow_forward
- Technician A says that if an engine had good results from a compression test, it will have good results from a cylinder leakage test Technician B says that if an engine had good results from a cylinder leakage test, it will have good results from a running compression test Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says that the engine oil drain plug typically needs to be replaced with a new one at each oil change. Technician B says that engine oil drain plugs must be tightened with a torque wrench when they are installed. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward1.Name type of failures in engine blocksarrow_forward
- Which of these provides stringent classifications formulated for engine oils used in European vehicles? Select one: a. SAE b. API c. ILSAC d. ACEAarrow_forwardAutomotive cooling system problems are being discussed. Technician A states that engine overheating is a common failure. Technician B states that an engine remaining below proper engine operating temperature is a common failure. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor Barrow_forwardWhen discussing oil consumption: Technician A says using one-quart of oil every 2,000 miles is acceptable. Technician B says oil consumption may increase depending on driving conditions. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
- P Flag question An increase in oil prices will create a situation where consumers will start buying conventional cars. Select one: O a. True O b. False Clear my choicearrow_forwardTechnician A says that you may be able to smell antifreeze from a leaking heater core. Technician B says that you may be able to hear a loose belt when the engine is running. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardThe Diesel Opacity (Smoke Meter) Emissions Inspection procedure requires that the Certified Inspector use an approved diesel opacity (smoke meter) tester to check emissions at the tailpipe and that the following must also be hooked up during the test: 1,RPM (tach) probe and oil temperature probe. 2. Oil temperature probe only. 3. RPM (tach) probe only. 4. Camshaft postion sensor.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Principles of Lubrication | Automobile Engineering; Author: Magic Marks;https://www.youtube.com/watch?v=MGbbSxZTdCQ;License: Standard Youtube License