EBK AUTOMOTIVE TECHNOLOGY
5th Edition
ISBN: 9780100659841
Author: Halderman
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 24, Problem 3CQ
Why are the EGR gases cooled before entering the engine on some engines?
- a. Cool exhaust gas is more effective at controlling NOx emissions
- b. To help prevent the exhaust from slowing down
- c. To prevent damage to the intake valve
- d. To prevent heating the air-fuel mixture in the cylinder
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
It is a multiple choice marine diesel engine question, please specify the correct option.
What is the difference between the 2 types of crankcase ventilation
systems used in engines?
The gas/oil mixture used in a two stroke engine has been properly mixed. The carburetor high speed & cruise circuit is adjusted to lean. Tech a says that the lean adjustment may cause the engine to fail due to improper lubrication: tech b says that it may cause the engine to fail because of overheating. Who is correct?
Chapter 24 Solutions
EBK AUTOMOTIVE TECHNOLOGY
Ch. 24 - Prob. 1RQCh. 24 - Prob. 2RQCh. 24 - Prob. 3RQCh. 24 - How does a muffler quiet exhaust noise?Ch. 24 - Prob. 1CQCh. 24 - The air filter restriction indicator uses what to...Ch. 24 - Why are the EGR gases cooled before entering the...Ch. 24 - Prob. 4CQCh. 24 - How can fuel -injected engine intake manifolds be...Ch. 24 - What is a variable intake manifold?
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
23.23 A highly oxidized and uneven round bar is being turned on a lathe. Would you recommend a small or a large...
Manufacturing Engineering & Technology
3.3 It is known that a vertical force of 200 lb is required to remove the nail at C from the board. As the nail...
Vector Mechanics for Engineers: Statics
The spring of k and unstretched length 1.5R is attached to the disk at a radial distance of 0.75R from the cent...
Engineering Mechanics: Statics
What types of polymers are most commonly blow molded?
Degarmo's Materials And Processes In Manufacturing
Three rigid bodies, 2,3, and 4, are connected by four springs as shown in the figure. A horizontal force of 1,0...
Introduction To Finite Element Analysis And Design
Describe the structural changes that take place when a plain-carbon eutectoid steel is slowly cooled from the a...
Foundations of Materials Science and Engineering
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Carbon deposits on the intake valve or seat may cause the valve not to close properly. Tech a says that the flywheel will be harder to spin when starting the engine. Tech b says that the engine will loose power. Who is correct?arrow_forwardExplain the importance of keeping the pre-cleaner trash-free on enginearrow_forwardWhich emission control system introduces exhaust gases into the intake air to reduce the formation of NOXin the combustion chamber? EVAP EGR Air injection PCVarrow_forward
- Which of the following are not typically found in the block of a modern engine? a. Pistons b. Crankshaft c. Valves d. Oil pumparrow_forwardTechnician A says that only offshore engines are permitted to use port-helix metering fuel systems on EPA MY 2010 compliant and later engines. Technician B says that port-helix metering injection pumps can be used on current diesel engines when the peak power rating is less than 70 BHP (52 kW). Who is correct?arrow_forwardan engine is being discussed for lean running condition. technician A checks for air leak in the intake. Technician B checks for alcohol in the fuel. who is correct?arrow_forward
- For Diesel engine, the turbocharger will increase the pressure of a. air fuel mixture entering into cylinder O b. air and exahust gases entering into cycliner. O c. air entering in to cylinder. d. fuel entering into engine cylinderarrow_forwardWhich of the following is similar to a PCV valve but is specific to diesel engines? PCM EGR AIR CDRarrow_forward1 Before conducting a __________ test, disable the ignition and the __________ injection system. Most manufacturers recommend that the engine be __________ when testing.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
The Refrigeration Cycle Explained - The Four Major Components; Author: HVAC Know It All;https://www.youtube.com/watch?v=zfciSvOZDUY;License: Standard YouTube License, CC-BY