AUTOMOTIVE TECHNOLOGY-NATEF TASK SHEETS
6th Edition
ISBN: 9780135257418
Author: Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 24, Problem 6CQ
Why are the EGR gases cooled before entering the engine on some engines?
- a. Cool exhaust gas is more effective at controlling NOx emissions
- b. To help prevent the exhaust from slowing down
- c. To prevent damage to the intake valve
- d. To prevent heating the air-fuel mixture in the cylinder
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
While discussing GDI systems: Technician A says this type of system allows engines to run at very lean air fuel ratios and at higher than normal compression ratios. Texhnician B says that GDI systems eliminate the need to have an EGR valve on the engine. Who is correct?
While discussing GDI systems: Technician A says that this type of system allows engines to run at very lean air-fuel ratios and at higher-than-normal compression ratios. Technician B says that GDI systems eliminate the need to have an EGR valve on the engine. Who is correct?
What is the difference between the 2 types of crankcase ventilation
systems used in engines?
Chapter 24 Solutions
AUTOMOTIVE TECHNOLOGY-NATEF TASK SHEETS
Ch. 24 - What are three three main jobs of the air cleaner...Ch. 24 - How can fuel -injected engine intake manifolds be...Ch. 24 - What is a variable intake manifold?Ch. 24 - How does a muffler quiet exhaust noise?Ch. 24 - What is the purpose and function of exhaust system...Ch. 24 - The air filter restriction indicator uses what to...Ch. 24 - Air filters can remove particles and dirt as small...Ch. 24 - Why do many port fuel-injected engines use long...Ch. 24 - The upper portion of a two-part intake manifold is...Ch. 24 - Which of the following is/are terms for a variable...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
23.23 A highly oxidized and uneven round bar is being turned on a lathe. Would you recommend a small or a large...
Manufacturing Engineering & Technology
3.3 It is known that a vertical force of 200 lb is required to remove the nail at C from the board. As the nail...
Vector Mechanics for Engineers: Statics
The spring of k and unstretched length 1.5R is attached to the disk at a radial distance of 0.75R from the cent...
Engineering Mechanics: Statics
What types of polymers are most commonly blow molded?
Degarmo's Materials And Processes In Manufacturing
Three rigid bodies, 2,3, and 4, are connected by four springs as shown in the figure. A horizontal force of 1,0...
Introduction To Finite Element Analysis And Design
Describe the structural changes that take place when a plain-carbon eutectoid steel is slowly cooled from the a...
Foundations of Materials Science and Engineering
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What are three possible problems that can allow fuel pressure to rapidly bleed down once the engine is shut off?arrow_forwardName the three types of emissions being controlled in gasoline engines.arrow_forwardThe gas/oil mixture used in a two stroke engine has been properly mixed. The carburetor high speed & cruise circuit is adjusted to lean. Tech a says that the lean adjustment may cause the engine to fail due to improper lubrication: tech b says that it may cause the engine to fail because of overheating. Who is correct?arrow_forward
- Differentiate the two types of external combustion enginearrow_forwardCarbon deposits on the intake valve or seat may cause the valve not to close properly. Tech a says that the flywheel will be harder to spin when starting the engine. Tech b says that the engine will loose power. Who is correct?arrow_forwardExplain the importance of keeping the pre-cleaner trash-free on enginearrow_forward
- Which emission control system introduces exhaust gases into the intake air to reduce the formation of NOXin the combustion chamber? EVAP EGR Air injection PCVarrow_forwardWhich of the following are not typically found in the block of a modern engine? a. Pistons b. Crankshaft c. Valves d. Oil pumparrow_forwardTechnician A says that only offshore engines are permitted to use port-helix metering fuel systems on EPA MY 2010 compliant and later engines. Technician B says that port-helix metering injection pumps can be used on current diesel engines when the peak power rating is less than 70 BHP (52 kW). Who is correct?arrow_forward
- an engine is being discussed for lean running condition. technician A checks for air leak in the intake. Technician B checks for alcohol in the fuel. who is correct?arrow_forwardFor Diesel engine, the turbocharger will increase the pressure of a. air fuel mixture entering into cylinder O b. air and exahust gases entering into cycliner. O c. air entering in to cylinder. d. fuel entering into engine cylinderarrow_forwardWhich of the following is similar to a PCV valve but is specific to diesel engines? PCM EGR AIR CDRarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
The Refrigeration Cycle Explained - The Four Major Components; Author: HVAC Know It All;https://www.youtube.com/watch?v=zfciSvOZDUY;License: Standard YouTube License, CC-BY