Concept explainers
(A)
The dimension of A in inches.
Answer to Problem 16A
The dimension of A in inches is
Explanation of Solution
Given information:
The schematic diagram of the system is shown below.
Figure-(1)
Write the expression for the dimension in inches.
Here, the dimension in inches is
Calculation:
Substitute
Conclusion:
The dimension of A in inches is
(B)
The dimension of B in inches.
Answer to Problem 16A
The dimension of B in inches is
Explanation of Solution
Substitute
Conclusion:
The dimension of B in inches is
(C)
The dimension of C in inches.
Answer to Problem 16A
The dimension of C in inches is
Explanation of Solution
Substitute
Conclusion:
The dimension of C in inches is
(D)
The dimension of D in inches.
Answer to Problem 16A
The dimension of D in inches is
Explanation of Solution
Substitute
Conclusion:
The dimension of D in inches is
(E)
The dimension of E in inches.
Answer to Problem 16A
The dimension of E in inches is
Explanation of Solution
Substitute
Conclusion:
The dimension of E in inches is
(F)
The dimension of F in inches.
Answer to Problem 16A
The dimension of F in inches is
Explanation of Solution
Substitute
Conclusion:
The dimension of F in inches is
(G)
The dimension of G in inches.
Answer to Problem 16A
The dimension of G in inches is
Explanation of Solution
Substitute
Conclusion:
The dimension of G in inches is
(H)
The dimension of H in inches.
Answer to Problem 16A
The dimension of H in inches is
Explanation of Solution
Substitute
Conclusion:
The dimension of H in inches is
(I)
The dimension of I in inches.
Answer to Problem 16A
The dimension of I in inches is
Explanation of Solution
Substitute
Conclusion:
The dimension of I in inches is
(J)
The dimension of J in inches.
Answer to Problem 16A
The dimension of J in inches is
Explanation of Solution
Substitute
Conclusion:
The dimension of J in inches is
(K)
The dimension of K in inches.
Answer to Problem 16A
The dimension of K in inches is
Explanation of Solution
Substitute
Conclusion:
The dimension of K in inches is
(L)
The dimension of L in inches.
Answer to Problem 16A
The dimension of L in inches is
Explanation of Solution
Substitute
Conclusion:
The dimension of L in inches is
Want to see more full solutions like this?
Chapter 25 Solutions
EBK MATHEMATICS FOR MACHINE TECHNOLOGY
- Refer to the shaft shown in Figure 6-4. Determine the missing dimensions in the table using the dimensions given. All dimensions are in inches.arrow_forwardA 60° slot has been machined in a fixture. The slot is checked by placing a pin in the slot and indicating the distance between the top of the fixture and the top of the pin as shown. Compute distance H to 3 decimal places by using this formula. All dimensions are in inches. H=1.5D0.866Warrow_forwardThe machined plate distances shown in Figure 41-3 are dimensioned, in millimeters, in terms of x. Determine dimensions A-G.arrow_forward
- Three holes are drilled in the plate shown. All dimensions are in inches. Determine dimensions A and B to 3 decimal places.arrow_forwardDetermine the length A in Figure 4-3. All dimensions are in inches.arrow_forwardDetermine dimension x for each of these figures. a. All dimensions are in inches. b. All dimensions are in millimeters. c. Round the answer to 3 decimal places. All dimensions are in inches. d. Round the answer to 3 decimal places. All dimensions are in inchesarrow_forward
- A hole is cut in a rectangular metal plate as shown in Figure 4-8. To find the area of a rectangle, multiply the length by the width. Determine the area of the plate after the hole has been removed. All dimensions are in inches. The area will be in square inches.arrow_forwardSolve the following applied right triangle problems. Compute linear values to 3 decimal places, customary unit angles to the nearer minute, and metric angles to the nearer hundredth degree. 24. Determine dimension x. All dimension are in millimeters. .arrow_forwardThe shaded piece shown is cut from a circular disk. Find the area of the piece. Round the answer to 1 decimal place. Dimensions are in inches.arrow_forward
- A single-threaded (or single-start) square-thread screw is shown in Figure 5-6. The lead of a screw is the distance that the screw advances in one turn (revolution). The lead is equal to the pitch in a single-threaded screw. Given the number of turns and the amount of screw advance, determine the leads.arrow_forwardAn artist wants to make a small monument in the shape of a square base topped by a right triangle, as shown below. The square base will be adjacent to one leg of the triangle. The other leg of the triangle will measure 2 feet and the hypotenuse will be 5 feet. (a) Use the Pythagorean Theorem to find the length of a side of the square base. Round your answer to the nearest tenth of a foot. (b) Find the exact area of the face of the square base.arrow_forwardGiven: In Figure 39-12, s is the length of a side of a hexagon, r isthe radius of the inside circle, and R is the radius of the outside circle. a. What is the length of r if r equals the product of 0.866 and the length of a side of the hexagon? b. What is the length of R if R equals the product of 1.155 and the radius of the inside circle? c. What is the area of the hexagon if the area equals the product of 2.598 and the square of the radius of the outside circle?arrow_forward
- Mathematics For Machine TechnologyAdvanced MathISBN:9781337798310Author:Peterson, John.Publisher:Cengage Learning,Elementary AlgebraAlgebraISBN:9780998625713Author:Lynn Marecek, MaryAnne Anthony-SmithPublisher:OpenStax - Rice UniversityAlgebra & Trigonometry with Analytic GeometryAlgebraISBN:9781133382119Author:SwokowskiPublisher:Cengage