EBK 3I-EBK: WELDING PRINCIPLES & APPLIC
8th Edition
ISBN: 9780176919764
Author: Jeffus
Publisher: VST
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 27, Problem 19R
What problems can occur to stainless steel as it is allowed to form carbide precipitation during welding?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
What are the advantages of MIG welding on stainless steels?
What are the possible defects of MIG welding on stainless steels?
Welding stainless steel is a complicated process because (uniform / intergranular / erosion) corrosion may happen, to avoid this issue post-weld-heat treatment is conducted to (precipitate / dissolve) carbide particles.
Chapter 27 Solutions
EBK 3I-EBK: WELDING PRINCIPLES & APPLIC
Ch. 27 - What is meant when a metal is said to have good...Ch. 27 - What does the term weldability involve?Ch. 27 - What properties of a metal can be affected by the...Ch. 27 - Referring to Table 27-2, what commercial joining...Ch. 27 - Referring to Table 27-2, what commercial joining...Ch. 27 - Referring to Table 27-2, what types of metals can...Ch. 27 - What two organizations have developed systems for...Ch. 27 - Explain the steel classification number 1030.Ch. 27 - Referring to Table 27-3, what is the composition...Ch. 27 - What is the maximum allowable percentage of...
Ch. 27 - According to Table 27-4, at what level of carbon...Ch. 27 - What factors other than carbon affect a steel's...Ch. 27 - Why would some low-carbon steels have severe...Ch. 27 - What must be done to steels before welding and...Ch. 27 - Why are high-carbon steels preheated before...Ch. 27 - Explain how to weld tool steel with the oxyfuel...Ch. 27 - Why must cracks in the martensite layer of...Ch. 27 - Prob. 18RCh. 27 - What problems can occur to stainless steel as it...Ch. 27 - Why should stainless steel not be held at a...Ch. 27 - What are the different uses for the three types of...Ch. 27 - Referring to Table 27-6, what diameter SMA welding...Ch. 27 - Why must cast iron weld metal be ductile?Ch. 27 - Why should copper be welded with high currents and...Ch. 27 - Why can't aluminum oxide be melted off aluminum?Ch. 27 - Why are aluminum welds likely to cause distortion...Ch. 27 - Prob. 27RCh. 27 - What do the letters and numbers in a magnesium...Ch. 27 - How can a part be cleaned before it is welded?Ch. 27 - How can a spark test be used to identify metals?
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What stainless steel(s) would a. have low creep at high temperatures? b. be used for food service equipment?arrow_forwardWhy must cracks in the martensite layer of high-manganese steels be removed?arrow_forwardWhat are some materials (high alloy casted) that have excellent wear resistance and weldability with little to no post weld heat treatmentarrow_forward
- 8) The correct ways to control liquation cracking tendency in fusion weld joint are I. Use of filler metal that solidifies before the partially melted zone I. Use of single pass welding with higher net heat input instead of multipass welding III. Use of high energy density processes IV. Preheating the substrates V. Use of base metals with fine grain structure OI, II, and III II, and IV OII, IV, and V O II, III and IVarrow_forwardReferring to Table 27-2, what commercial joining process can be used to braze sheet stainless steel?arrow_forwardWhat factors other than carbon affect a steel's ability to be welded?arrow_forward
- What happens to a quench hardened tool or machine part that was not tempered when it is subject to shock loads or bending stress?arrow_forward3) Improper cleaning of faying surfaces during fusion welding of carbon steels will primarily lead to Wider heat affected zone O Higher residual stresses Entrapment of gases and formation of inclusions O Higher fracture toughness of weld jointarrow_forwardCan aluminum be quench-hardened? Why or why not?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Metal Joining Process-Welding, Brazing and Soldering; Author: Toc H Kochi;https://www.youtube.com/watch?v=PPT5_fDSzGY;License: Standard YouTube License, CC-BY