AUTOMATIC TRANSMISSION+TRANS.>CUSTOM<
6th Edition
ISBN: 9781337495370
Author: ERJAVEC
Publisher: CENGAGE C
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 27, Problem 1RQ
Name the three types of stress testing used to test for intermittent ignition component problems and list the procedures for conducting each type of test.
Expert Solution & Answer
To determine
The types of stress testing used for testing intermittent ignition problems.
Answer to Problem 1RQ
There are three types of stress testing used for conducting testing the intermittent ignition component problems. They are cold testing, heat testing, and moisture testing.
Explanation of Solution
The stress testing is of three types:
- Cold testing
- Heat testing
- Moisture testing
Now, the following are the methods of stress testing:
Procedure to be followed in case of cold testing:
- In this kind of testing, first, the ignition components are cooled by using a liquid which is later used as a cooling agent.
- Then, the traces of any malfunction or problem in the pattern within the dwell zone is observed and checked.
- Then, this same procedure is being followed and repeated again for the other components in this test. By doing this, results are compared and bad ones are observed and pointed out.
Procedure to be followed in case of heat testing:
- In this testing, the ignition components are heated by using the heat gun which puts hot air in the components. Doing this process, the degree should be kept in that much value so that plastic and wire does not get damaged.
- Then, the traces of any malfunction or problems in the pattern within the dwell zone and the area of limited flow is observed and checked.
- In case of malfunction found, the terminals should be cleaned and coated.
Procedure to be followed in case of moisture testing:
- In this testing, the ignition components are being sprayed a little with water and the raster which is connected to the scope provides the pattern of the problem which is found in it.
- Although, in some cases, instead of using the scope, the problems can be identified by hearing the shutter.
Conclusion:
Thus, there are three kinds of stress testing.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Name the three types of stress testing used to test forintermittent ignition component problems and listthe procedures for conducting each type of test.
What are the equipment/apparatus required to conduct performance test of internal combustion engine?
Identify two (2) mechanical components that are most likely to cause abnormal noises in a diesel engine and briefly explain the associated testing procedure used to confirm the fault. (70 - 140 words)
Chapter 27 Solutions
AUTOMATIC TRANSMISSION+TRANS.>CUSTOM<
Ch. 27 - Name the three types of stress testing used to...Ch. 27 - Prob. 2RQCh. 27 - Name the three types of trace pattern display...Ch. 27 - Prob. 4RQCh. 27 - List at least two methods of checking the...Ch. 27 - What happens if one of the ground electrodes of a...Ch. 27 - True or False? The first test when checking a...Ch. 27 - Richer air-fuel mixtures. a. decrease the...Ch. 27 - Prob. 9RQCh. 27 - What does a slope in the spark line represent?
Ch. 27 - True or False? On some engines, if the gap between...Ch. 27 - What is the typical procedure for checking the...Ch. 27 - While checking a pickup coil with an ohmmeter, a...Ch. 27 - A CKP sensor can be checked with all of the...Ch. 27 - Which of the following will cause one or more, but...Ch. 27 - Prob. 1ASRQCh. 27 - Prob. 2ASRQCh. 27 - Prob. 3ASRQCh. 27 - Technician A says that EMI can affect sensor...Ch. 27 - While discussing waste spark EI systems:...Ch. 27 - While discussing how to test a Hall-effect...Ch. 27 - While discussing the possible causes for a...Ch. 27 - Prob. 8ASRQCh. 27 - While discussing EI service and diagnosis:...Ch. 27 - While discussing engine misfire diagnosis:...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- List the five steps to be followed when using a penetrant test.arrow_forwardWhat hardness testing scale uses many different penetrators and loads?arrow_forward1. What type of measurements are most often obtained when testing vehicle circuits ? 2. What measurement is common in testing audio system and many modern door lock system ?arrow_forward
- Standard operating procedures for internal combustion engine(mounted on vehicle)arrow_forwardWhat are the suggestions to prevent the occurrence of failures in car clutch?arrow_forward13) Which one of the following is the Non destructive test a. Ultrasonic test b. Tensile test c. Brinell Hardness test d. Vickers hardness testarrow_forward
- 1.Name type of failures in engine blocksarrow_forwardshow solution and all steps. thermo 2. first solve with cold air standard, then solve without cold air standard. label part 1 and part 2arrow_forwarda) What would be the best instrument to use for detecting steam leaks on a superheated steam line, a Vibration analyser, an Ultrasound detector or a Thermal Imaging Camera? b) Explain your choice of instrument for question “a”arrow_forward
- What two major safety problems does hydrogen present?arrow_forwardHow can ambient temperature and pressure affect vehicle emission rates?arrow_forwardIn an automatic AWD vehicle, normally one axle receives all the torque; when slippage occurs, 50 percent of the torque can be sent to the other axle by _____ means. Question 15 options: hydraulic mechanical electrical all answers are correctarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningPrecision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Material Properties 101; Author: Real Engineering;https://www.youtube.com/watch?v=BHZALtqAjeM;License: Standard YouTube License, CC-BY