Welding: Principles and Applications (MindTap Course List)
8th Edition
ISBN: 9781305494695
Author: Larry Jeffus
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 27, Problem 26R
Why are aluminum welds likely to cause distortion and cracking?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Discuss the arc welding quality and type of defects involved? What are the inspection and testing methods available to check the quality of the weld joint?
It has been reported that gas–tungsten arc welds of aluminum made in the overhead position (assumed lap weld joint) tend to have a significantly higher porosity level than those made in the flat position:
Explain why
Sketch the general view of the overhead position
Indicate where the (most probable) location of the porosity
Give information about residual stresses and distortions after welding.
Chapter 27 Solutions
Welding: Principles and Applications (MindTap Course List)
Ch. 27 - What is meant when a metal is said to have good...Ch. 27 - What does the term weldability involve?Ch. 27 - What properties of a metal can be affected by the...Ch. 27 - Referring to Table 27-2, what commercial joining...Ch. 27 - Referring to Table 27-2, what commercial joining...Ch. 27 - Referring to Table 27-2, what types of metals can...Ch. 27 - What two organizations have developed systems for...Ch. 27 - Explain the steel classification number 1030.Ch. 27 - Referring to Table 27-3, what is the composition...Ch. 27 - What is the maximum allowable percentage of...
Ch. 27 - According to Table 27-4, at what level of carbon...Ch. 27 - What factors other than carbon affect a steel's...Ch. 27 - Why would some low-carbon steels have severe...Ch. 27 - What must be done to steels before welding and...Ch. 27 - Why are high-carbon steels preheated before...Ch. 27 - Explain how to weld tool steel with the oxyfuel...Ch. 27 - Why must cracks in the martensite layer of...Ch. 27 - Prob. 18RCh. 27 - What problems can occur to stainless steel as it...Ch. 27 - Why should stainless steel not be held at a...Ch. 27 - What are the different uses for the three types of...Ch. 27 - Referring to Table 27-6, what diameter SMA welding...Ch. 27 - Why must cast iron weld metal be ductile?Ch. 27 - Why should copper be welded with high currents and...Ch. 27 - Why can't aluminum oxide be melted off aluminum?Ch. 27 - Why are aluminum welds likely to cause distortion...Ch. 27 - Prob. 27RCh. 27 - What do the letters and numbers in a magnesium...Ch. 27 - How can a part be cleaned before it is welded?Ch. 27 - How can a spark test be used to identify metals?
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What chemicals alloys are a. considered to be contaminants to the weld metal? b. used to increase tensile strength in the weld metal? c. used to increase corrosion resistance? d. used to reduce creep?arrow_forwardWhat are the major atmospheric contaminations of the molten weld metal?arrow_forwardWhat is a good indication that the molten weld pool is not being protected from oxidation?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Differences between Temporary Joining and Permanent Joining.; Author: Academic Gain Tutorials;https://www.youtube.com/watch?v=PTr8QZhgXyg;License: Standard Youtube License