Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 27, Problem 6ASRQ
While discussing how to test a Hall-effect crankshaft position sensor: Technician A says that a logic probe can be used. Technician B says that a DMM can be used. Who is correct?
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
While discussing throttle-by-wire systems: Technician A says that a spring on the throttle shaft provides the limp-home feature. Technician B says that most systems have redundant processors and the TP and accelerator pedal sensors send redundant input signals. Who is correct?A. Tech A
B. Tech B
C. Both A and B
D. Neither A nor B
Technician A says that negative caster provides directional stability . Technician B says that pos caster results from excessive positive cam ber . Who is correct ?
Explain about sensors using for speed, throttle position and crank shaft position with the help of neat diagram.
Chapter 27 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 27 - Name the three types of stress testing used to...Ch. 27 - Prob. 2RQCh. 27 - Name the three types of trace pattern display...Ch. 27 - Prob. 4RQCh. 27 - List at least two methods of checking the...Ch. 27 - What happens if one of the ground electrodes of a...Ch. 27 - True or False? The first test when checking a...Ch. 27 - Richer air-fuel mixtures. a. decrease the...Ch. 27 - Prob. 9RQCh. 27 - What does a slope in the spark line represent?
Ch. 27 - True or False? On some engines, if the gap between...Ch. 27 - What is the typical procedure for checking the...Ch. 27 - While checking a pickup coil with an ohmmeter, a...Ch. 27 - A CKP sensor can be checked with all of the...Ch. 27 - Which of the following will cause one or more, but...Ch. 27 - Prob. 1ASRQCh. 27 - Prob. 2ASRQCh. 27 - Prob. 3ASRQCh. 27 - Technician A says that EMI can affect sensor...Ch. 27 - While discussing waste spark EI systems:...Ch. 27 - While discussing how to test a Hall-effect...Ch. 27 - While discussing the possible causes for a...Ch. 27 - Prob. 8ASRQCh. 27 - While discussing EI service and diagnosis:...Ch. 27 - While discussing engine misfire diagnosis:...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- when discussing shift problems, technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems. technician b says that poor shift boot alignment can cause a transaxle to jump out of geararrow_forwardWhile discussing SFI systems: Technician A says that when the injection system fires according to crankshaft position and speed, it is operating in the synchronous mode. Technician B says that one of the advantages of SFI systems is that they are always in the synchronous mode. Who is correct?arrow_forwardExplain the operation of the accelerator position sensors?arrow_forward
- When discussing shift problems,Technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems.Technician B says that poor shift boot alignment can cause a transaxle to jump out of gear?arrow_forwardBefore making a clutch adjustment, it is necessary to______. a. measure clutch pedal free travel b. lubricate the clutch linkage c. check the hydraulic fluid level d. place the transmission in reversearrow_forwardTrue or False? On some engines, if the gap between the crankshaft sensor and its trigger wheel is outside specifications, the sensor should be replaced.arrow_forward
- A throttle position sensor has _________ . a- a 0-5 volts signal output terminal b- a 5-volt reference input terminal c- all answers are correct d- a ground terminalarrow_forwardTechnician A says that throttle position is an important input in most electronic shift control systems. Technician B says that vehicle speed is an important input for most electronic shift control systems. Who is correct?arrow_forwardWhich of the following would not cause noise while driving in 2WD under a heavy throttle? a. Faulty ignition switch b. Worn transfer case clutch c. Inoperative locking hubs d. Bad front half shaftarrow_forward
- Which of the following is the most likely cause of a lean condition during acceleration and cruising speeds? a. A defective oxygen sensor b. A defective PCM c. A defective ECT sensor d. A defective MAF sensorarrow_forwardWhile discussing the cause of a pulsating clutch pedal: Technician A says that this can be caused by a low fluid level in the hydraulic system. Technician B says that this can be caused by a warped flywheel. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhile discussing transmission adaptive learning: Technician A says that the transmission learns to respond according to the current condition of the engine and transmission. Technician B says that the TCM learns to respond to the driver’s driving habits. Who is correct?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY