Find a second frequency where the current in the speaker of Example 28.4 has half its maximum value.
EXAMPLE 28.4 An RLC Circuit: Designing a Loudspea
Current flows to the midrange speaker in a loudspeaker system through a 2.2-mH inductor in series with a capacitor. (a) What should the capacitance be so that a given voltage produces the greatest current at 1.0 kHz? (b) If the same voltage produces half this current at 618 Hz, what is the speaker’s resistance? (c) If the peak output voltage of the amplifier is 24 V, what will the peak capacitor voltage be at 1 kHz?
Want to see the full answer?
Check out a sample textbook solutionChapter 28 Solutions
Essential University Physics -Modified MasteringPhysics Access
Additional Science Textbook Solutions
Essential University Physics: Volume 1 (3rd Edition)
Physics for Scientists and Engineers: A Strategic Approach, Vol. 1 (Chs 1-21) (4th Edition)
Physics for Scientists and Engineers: A Strategic Approach with Modern Physics (4th Edition)
University Physics Volume 1
College Physics
Lecture- Tutorials for Introductory Astronomy
- A 60.0-ft resistor is connected in series with a 30.0-F capacitor and a source whose maximum voltage is 120 V, operating at 60.0 Hz. Find (a) the capacitive reactance of the circuit, (b) the impedance of the circuit, and (c) the maximum current in the circuit. (d) Does the voltage lead or lag the current? (e) How will adding an inductor in series with the existing resistor and capacitor affect the current? Explain.arrow_forwardAfter the switch is dosed in the LC circuit shown in Figure CQ32.8, the charge on the capacitor is sometimes zero, but at such instants the current in the circuit is not zero. How is this behavior possible? Figure CQ32.8 Conceptual Question 8 and Problems 52, 54, and. 15.arrow_forwardIn a series RLC circuit with a maximum current of 0.250 A, an AC source with Vmax= 115 V operating at 60.0 Hz is connected to a 325-mH inductor, a 7.50-F capacitor, and a resistor with unknown resistance R. Draw a phasor diagram for this circuit, including the current, the potential difference across each of the circuit elements, and the source emf. Draw your diagram with the current phasor pointing upward along the vertical axis.arrow_forward
- An inductor (L = 400 mH), a capacitor (C = 4.43 F), C1 and a resistor (R = 500 11) are connected in series. A 50.0-Hz AC] source produces a peak current of 250 mA in the circuit, (a) Calculate the required peak voltage Vmax (b) Determine the phase angle by which the current leads or lags the applied voltage.arrow_forwardProblems 71 and 72 paired. Figure P33.71 shows a series RLC circuit with a 25.0- resistor, a 430.0-mH inductor, and a 24.0-F capacitor connected to an AC source with Vmax = 60.0 V operating at 60.0 Hz. What is the maximum voltage across the a. resistor, b. inductor, and c. capacitor in the circuit? FIGURE P33.71 Problems 71 and 72.arrow_forwardA series RLC circuit has resistance R = 50.0 and inductance L. = 0.500 H. (a) Find the circuits capacitance C if the voltage source operates at a frequency of f = 60.0 Hz and the impedance is Z = R = 50.0 . (b) What is the phase angle between the current and the voltage?arrow_forward
- A 2.0-F capacitor is charged to a potential difference of 12.0 V and then connected across a 0.40-mH inductor. What is the current in the circuit when the potential difference across the capacitor is 6.0 V?arrow_forwardA 1.5k resistor and 30-mH inductor are connected in series, as below, across a120-V(rms)ac power source oscillating at 60-Hz frequency. (a) Find the current in the circuit. (b) Find the voltage drops across the resistor and inductor. (C) Find the impedance of the circuit. (d) Find the power dissipated in the resistor. (e) Find the power dissipated in the inductor. (1) Find the power produced by the source.arrow_forwardAn RLC series circuit hag a 1.00 k(register, a 150 (H inductor, and a 25.0 nF capacitor. (a) Find the circuit’s impedance at 500 Hz. (b) Find the circuit’s impedance at 7.50 kHz. (c) It the voltage source has Vrms = 408 V, what is Irms at each frequency? (d) What is the resonant frequency of the circuit? (e) What is Irms at resonance?arrow_forward
- One application of an RL circuit is the generation of lime-varying high voltage from a low-volt age source as shown in Figure P32.82. (a) What is the current in the circuit a long time after the switch has been in position a? (b) Now the switch is thrown quickly from a to b. Compute the initial voltage across each resistor and across the inductor. (c) How much time elapses before the voltage across the inductor drops to 12.0 Y?arrow_forwardAn LC circuit in an AM tuner (in a car stereo) uses a coil with an inductance of 2.5 mH and a variable capacitor. If the natural frequency of the circuit is to be adjustable over the range 540 to 1600 kHz (the AM broadcast band), that range of capacitance is required?arrow_forwardA series RLCcircuit contains a 20.0- resistor, a 0.750-F capacitor, and a 120-mH inductor. (i) 11 a sinusoidally varying rms voltage of 120 V at f = 500 Hz is applied across this combination of elements, what is the rms current in the circuit? (a) 2.33 A (b) 6.00 A (c) 10.0 A (d) 17.0 A (e) none of those answers (ii) What If? W hat is the rms current in the circuit when operating at its resonance frequency? Choose from the same possibilities as in part (i).arrow_forward
- College PhysicsPhysicsISBN:9781285737027Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningCollege PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningPhysics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
- Physics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning