Concept explainers
Compute the power absorbed by each element in the circuit of Fig. 3.68 if the mysterious element X is (a) a 13 Ω resistor; (b) a dependent voltage source labeled 4v1, “+” reference on top; (c) a dependent voltage source labeled 4ix, “+” reference on top.
FIGURE 3.68
(a)
Find the power absorbed by each element.
Answer to Problem 28E
Power absorbed by
Explanation of Solution
Given Data:
Element
Formula used:
The expression for power absorbed by voltage source is as follows.
Here,
The expression for power absorbed by resistor is as follows.
Here,
Calculation:
The circuit diagram is redrawn as shown in Figure 1.
Refer to the redrawn Figure 1.
The expression for KVL in mesh
Here,
Substitute
Rearrange equation (4) for
Current is leaving the positive terminal and we are calculating power absorbed hence current should leave by negative terminal so we will use magnitude of voltage with negative sign, therefore, value of
Substitute
So power absorbed by independent voltage source
Substitute
So, the power absorbed by resistor
Substitute
So power absorbed by resistor
Substitute
So power absorbed by resistor
Substitute
So power absorbed by independent voltage source
Substitute
So power absorbed by resistor
Conclusion:
Thus, power absorbed by
(b)
Find power absorbed by each element.
Answer to Problem 28E
Power absorbed by
Explanation of Solution
Given Data:
Element
Calculation:
The circuit diagram is redrawn as shown in Figure 2,
Refer to the redrawn Figure 2,
The expression for KVL in mesh
Here,
The expression for voltage
Here,
The expression for voltage
Here,
Refer to the redrawn Figure 2,
Substitute
Substitute
Rearrange equation (9) for
Current is leaving the positive terminal and we are calculating power absorbed hence current should leave by negative terminal so we will use magnitude of voltage with negative sign, therefore, value of
Substitute
So power absorbed by independent voltage source
Substitute
So power absorbed by resistor
Substitute
So power absorbed by resistor
Substitute
Substitute
Substitute
So power absorbed by dependent voltage source
Substitute
So power absorbed by independent voltage source
Substitute
So power absorbed by resistor
Conclusion:
Thus, power absorbed by
(c)
Find power absorbed by each element.
Answer to Problem 28E
Power absorbed by
Explanation of Solution
Given Data:
Element
Calculation:
The circuit diagram is redrawn as shown in Figure 3.
Refer to the redrawn Figure 3,
The expression for KVL in mesh
Here,
The expression for voltage
Here,
Refer to the redrawn Figure 2,
Substitute
Rearrange equation (12) for
Current is leaving the positive terminal and we are calculating power absorbed hence current should leave by negative terminal so we will use magnitude of voltage with negative sign, therefore, value of
Substitute
So power absorbed by independent voltage source
Substitute
So power absorbed by resistor
Substitute
So power absorbed by resistor
Substitute
Substitute
So power absorbed by dependent voltage source
Substitute
So power absorbed by independent voltage source
Substitute
So power absorbed by resistor
Conclusion:
Thus, power absorbed by
Want to see more full solutions like this?
Chapter 3 Solutions
Loose Leaf for Engineering Circuit Analysis Format: Loose-leaf
- Lesson: signals and systems Thanx for answer <3arrow_forwardKindly provide CLEAR and COMPLETE solutions #3arrow_forwardA 33kv, 3phase, 50hz underground line, 3.4km long, uses three single core cables. Each cable has a core diameter of 2.5cm and the radial thickness of insulation is 0.6cm. the relative permittivity of the dielectric is 3.1. Find (i) maximum stress and (ii) total charging kVARarrow_forward
- Q3 / A: The Arton device is designed to configure an ammeter with ranges of 10 ampere, 5 ampere, and 1 ampere, given that the internal resistance of the circuit-breaker circuit is 50 ohms and the full current deviation is 1 milliampere.arrow_forwardKnowing that R1 = 1kΩ, R2 = 2.2kΩ, R3 = 1.2kΩ, R4 = 1kΩ, R5 = 1.2kΩ, Vs = 5V, calculate, using the Kirchhoff Current Law (KCL), the current and voltage values for the components the circuit.arrow_forwardCompute the power absorbed by each element in the circuit of Fig. 3.67 if themysterious element X is (a) a 13 resistor; (b) a dependent voltage sourcelabeled 4v1, “” reference on top; (c) a dependent voltage source labeled 4ix,“” reference on toparrow_forward
- Calculate I1 and I2 using Current Division for the Circuit in Fig. 3.5arrow_forwardA certain appliance requires 225 watts when it is switched on. How much would it cost to run for m minutes, at a cost of d dollars per kilowatt-hour? Express your answer algebraically.arrow_forwardA natural waterfalls, 50 meters high, constantly discharges 1.3m3 per second. A minihydroelectric plant is to be constructed at the bottom of the waterfalls. Calculate theelectric generator kW rating, assuming 90% mechanical to electrical conversion efficiencyand water turbine design efficiency of 70%.arrow_forward
- Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSONDelmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningProgrammable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
- Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill EducationElectric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSONEngineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,