Fox and McDonald's Introduction to Fluid Mechanics
9th Edition
ISBN: 9781118912652
Author: Philip J. Pritchard, John W. Mitchell
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 3, Problem 77P
The barge shown weighs 40 tons and carries a cargo of 40 tons. Calculate its draft in freshwater.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A dam 30.5m long retains 8 m of fresh water and is inclined at an angle of 60 degrees. Calculate the magnitude of the resultant force on the dam and the location of the center of pressure.
For the three-liquid system shown, compute h 1 and h 2 .Neglect the air density.
As shown in the illustration, a 6-m-wide, 15-m-long barge is filled with rocks and floats in water. Assume that the rocks' and barge's center of gravity, G, is positioned along the centerline at the barge's surface. What is the metacentric height in meters if the barge carrying the rocks weights 1,765.8 kN?
Chapter 3 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Ch. 3 - Because the pressure falls, water boils at a lower...Ch. 3 - Ear popping is an unpleasant phenomenon sometimes...Ch. 3 - When you are on a mountain face and boil water,...Ch. 3 - Your pressure gauge indicates that the pressure in...Ch. 3 - A 125-mL cube of solid oak is held submerged by a...Ch. 3 - The tube shown is filled with mercury at 20C....Ch. 3 - Calculate the absolute and gage pressure in an...Ch. 3 - An open vessel contains carbon tetrachloride to a...Ch. 3 - A hollow metal cube with sides 100 mm floats at...Ch. 3 - Compressed nitrogen (140 lbm) is stored in a...
Ch. 3 - If at the surface of a liquid the specific weight...Ch. 3 - In the deep ocean the compressibility of seawater...Ch. 3 - Assuming the bulk modulus is constant for sea...Ch. 3 - An inverted cylindrical container is lowered...Ch. 3 - A water tank filled with water to a depth of 16 ft...Ch. 3 - A partitioned tank as shown contains water and...Ch. 3 - Consider the two-fluid manometer shown. Calculate...Ch. 3 - The manometer shown contains water and kerosene....Ch. 3 - Determine the gage pressure in kPa at point a, if...Ch. 3 - With the manometer reading as shown, calculate px....Ch. 3 - Calculate px py for this inverted U-tube...Ch. 3 - An inclined gauge having a tube of 3-mm bore, laid...Ch. 3 - Water flows downward along a pipe that is inclined...Ch. 3 - A reservoir manometer has vertical tubes of...Ch. 3 - A rectangular tank, open to the atmosphere, is...Ch. 3 - The sketch shows a sectional view through a...Ch. 3 - The manometer reading is 6 in. when the funnel is...Ch. 3 - A reservoir manometer is calibrated for use with a...Ch. 3 - The inclined-tube manometer shown has D = 96 mm...Ch. 3 - The inclined-tube manometer shown has D = 76 mm...Ch. 3 - A barometer accidentally contains 6.5 inches of...Ch. 3 - A water column stands 50 mm high in a 2.5-mm...Ch. 3 - Consider a small-diameter open-ended tube inserted...Ch. 3 - Compare the height due to capillary action of...Ch. 3 - If atmospheric pressure at the ground is 101.3 kPa...Ch. 3 - If the temperature in the atmosphere is assumed to...Ch. 3 - A hydropneumatic elevator consists of a...Ch. 3 - Semicircular plane gate AB is hinged along B and...Ch. 3 - A circular gate 3 m in diameter has its center 2.5...Ch. 3 - For the situation shown, find the air pressure in...Ch. 3 - What is the pressure at A? Draw a free body...Ch. 3 - A plane gate of uniform thickness holds back a...Ch. 3 - A rectangular gate (width w = 2 m) is hinged as...Ch. 3 - Gates in the Poe Lock at Sault Ste. Marie,...Ch. 3 - Calculate the minimum force P necessary to hold a...Ch. 3 - Calculate magnitude and location of the resultant...Ch. 3 - Calculate magnitude and location of the resultant...Ch. 3 - A window in the shape of an isosceles triangle and...Ch. 3 - A large open tank contains water and is connected...Ch. 3 - The circular access port in the side of a water...Ch. 3 - The gate AOC shown is 6 ft wide and is hinged...Ch. 3 - The gate shown is hinged at H. The gate is 3 m...Ch. 3 - For the dam shown, what is the vertical force of...Ch. 3 - The parabolic gate shown is 2 m wide and pivoted...Ch. 3 - An open tank is filled with water to the depth...Ch. 3 - A dam is to be constructed using the cross-section...Ch. 3 - The quarter cylinder AB is 10 ft long. Calculate...Ch. 3 - Calculate the magnitude, direction (horizontal and...Ch. 3 - A hemispherical shell 1.2 m in diameter is...Ch. 3 - A cylindrical weir has a diameter of 3 m and a...Ch. 3 - If you throw an anchor out of your canoe but the...Ch. 3 - A hydrometer is a specific gravity indicator, the...Ch. 3 - A cylindrical can 76 mm in diameter and 152 mm...Ch. 3 - If the 10-ft-long box is floating on the oil-water...Ch. 3 - The timber weighs 40 lb/ft3 and is held in a...Ch. 3 - Find the specific weight of the sphere shown if...Ch. 3 - The fat-to-muscle ratio of a person may be...Ch. 3 - An open tank is filled to the top with water. A...Ch. 3 - If the timber weighs 670 N, calculate its angle of...Ch. 3 - The barge shown weighs 40 tons and carries a cargo...Ch. 3 - Quantify the experiment performed by Archimedes to...Ch. 3 - Hot-air ballooning is a popular sport. According...Ch. 3 - It is desired to use a hot air balloon with a...Ch. 3 - The opening in the bottom of the tank is square...Ch. 3 - A balloon has a weight (including crew but not...Ch. 3 - A helium balloon is to lift a payload to an...Ch. 3 - The stem of a glass hydrometer used to measure...Ch. 3 - A sphere of radius R is partially immersed to...Ch. 3 - A sphere of 1-in.-radius made from material of...Ch. 3 - You are in the Bermuda Triangle when you see a...Ch. 3 - Three steel balls (each about half an inch in...Ch. 3 - A proposed ocean salvage scheme involves pumping...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
The column is constructed from high-strength concrete and eight A992 steel reinforcing rods. If the column is s...
Mechanics of Materials (10th Edition)
Determine the force in each member of the Pratt truss, and state if the members are in tension or compression. ...
Engineering Mechanics: Statics
If it is placed on the ground for which the coefficient of kinetic friction is c = 0.5, determine the time requ...
Engineering Mechanics: Dynamics (14th Edition)
The force for equilibrium in each cord.
Engineering Mechanics: Statics & Dynamics (14th Edition)
A piston/cylinder has a water volume separated in VA=0.2m3 and VB=0.3m3 by a stiff membrane (Fig. P3.139). The ...
Fundamentals Of Thermodynamics
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The thin-walled cylindrical can with a spherical dimple weighs 0.2 lb. Determine the force P required to push the can into water to a depth of 8 in. Use =0.036lb/in.3 for water.arrow_forwardThe hemispherical glass bowl is filled with water. Find the location y of the center of gravity of the filled bowl. Approximate the bowl as a thin shell of radius R=6.15in. Use 1=162lb/ft3 for glass and 2=62.4lb/ft3 for water.arrow_forwardFind the elevation h (km) where the weight of an object is one-tenth its weight on the surface of the earth.arrow_forward
- A man weighs 170 lb on the surface of the earth. Compute his weight in an airplane flying at an elevation of 28 000 ft.arrow_forwardEvaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen, air, and saturated steam at a temperature of 100C. Let D=1m,U=1m/sec, and hc=1W/m2K.arrow_forwardThe weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.arrow_forward
- A concrete seawater dam is shown in cross section. Is the dam safe against tipping about edge A? The mass densities are 24000kg/m3 for concrete and 1030kg/m3 for seawater.arrow_forwardCalculate the resultant of hydrostatic force on the gate. What vertical force P is necessary to lift the gate at point A. The weight of the gate is 800 N. Width of the gate is 1.6 m.arrow_forwardA vertical bulk head is 2 meters wide and 3.7 meters high. It has fresh water on one side to a depth of 3 meters and sea water on the other side to a depth of 3.5 meters. Calculate the resultant force on the door.arrow_forward
- A water tank of cross-sectional area 2.5 m2 and height 120 in contains 1500 (US) gallons of water. If the density of water is 1000 kg/m3, calculate the force on the base of the tank.arrow_forwardThe figure below shows a block of wood with total height H, submerged height h and square base with side b = 0.41 m, floating in a tank with water. a) Knowing that the wood density is d = 0.75, calculate: a) the ratio between the submerged height h and the total height of block H; b) the metacentric height, in meters, for the block to float, in the indicated configuration, with indifferent balance (critical); c) the value of H for the same situation as the previous item (indicate the unit).arrow_forwardIn Fig. , curved section AB is 5 m wide into the paperand is a 60 ° circular arc of radius 2 m. Neglecting atmosphericpressure, calculate the vertical and horizontalhydrostatic forces on arc AB .arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- International Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE LPrinciples of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Physics 33 - Fluid Statics (1 of 10) Pressure in a Fluid; Author: Michel van Biezen;https://www.youtube.com/watch?v=mzjlAla3H1Q;License: Standard YouTube License, CC-BY