Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
6th Edition
ISBN: 9780135257272
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 30, Problem 3CQ
Technician A says that an Audi five-valve engine uses three intake valves and two exhaust valves. Technician B says that it uses three exhaust valves and two intake valves. Which technician is correct?
- a. Technician A only
- b. Technician B only
- c. Both Technicians A and B
- d. Neither Technician A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Carbon deposits on the intake valve or seat may cause the valve not to close properly. Tech a says that the flywheel will be harder to spin when starting the engine. Tech b says that the engine will loose power. Who is correct?
Explain briefly
1. Valve lag
2. intake lag
INTRODUCTION ABOUT VALVE SYSTEM IN INTERNAL COMBUSTION ENGINE
Chapter 30 Solutions
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Ch. 30 - What is meant by the term crossflow head?Ch. 30 - Prob. 2RQCh. 30 - What is the recommended cylinder head...Ch. 30 - What are the advantages of using four valves per...Ch. 30 - How is valve stem-to-guide clearance measured?Ch. 30 - Cylinder heads with four valves flow more air than...Ch. 30 - Two technicians are discussing a Hemi engine....Ch. 30 - Technician A says that an Audi five-valve engine...Ch. 30 - The gasket surface of a cylinder head, as measured...Ch. 30 - A warped aluminum cylinder head can be restored to...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Select a mechanical component from Part 3 of this book (roller bearings, springs, etc.), go to the Internet, an...
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
Define or describe each type of fluid: (a) viscoelastic fluid (b) pseudoplastic fluid (c) dilatant fluid (d) Bi...
Fluid Mechanics: Fundamentals and Applications
A 20-lb force is applied to the control rod AB as shown. Knowing that the length of the rod is 9 in. and that t...
Statics and Mechanics of Materials
How is the hydrodynamic entry length defined for flow in a pipe? Is the entry length longer in laminar or turbu...
Fluid Mechanics Fundamentals And Applications
Determine the length of the cantilevered beam so that the maximum bending stress in the beam is equivalent to t...
Mechanics of Materials (10th Edition)
Describe the structural changes that take place when a plain-carbon eutectoid steel is slowly cooled from the a...
Foundations of Materials Science and Engineering
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The function of carburettor used in engine is to a. mix air, petrol and diesel in engines b. mix petrol and diesel in engines c. mix air and diesel in engines d. mix air and petrol in enginesarrow_forwardan engine is being discussed for lean running condition. technician A checks for air leak in the intake. Technician B checks for alcohol in the fuel. who is correct?arrow_forwardTechnician A says that broken engine mounts can cause the fan to hit the shroud. Technician B says that missing or broken air dams can cause an engine to overheat. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- The injector function in diesel engine is to a. inject fuel continusously when engine is running. b. inject fuel at the beginning of comprssion stroke c. inject fuel at the end of expansion stroke d. inject fuel at end of compression strokearrow_forwardExplain the Four - Stroke Cycle Engine Intake Compression Power Exhaustarrow_forward1. The purpose of running this injector balance test is to determine which injector is restricted, inoperative, or delivering fuel differently than the other injectors. Replacing a complete set of injectors can be expensive. a. Describe the step involve in conducting injector balance test. b. Based on the recorded data on the power balance test in Table 1. Explain the condition on each injector. Table 1 Data collected from power balance test. Injector 1 2 3 Initial pressure (psi) 45 45 45 Second pressure 32 36 25 (psi)arrow_forward
- During suction stroke of petrol engines, the following statement is correct. O a. Air alone enters through inlet valve and piston moves from BDC to TDC O b. Air fuel mixture enters through inlet valve and piston moves from BDC to TDC Air alone enters through inlet valve and piston moves from TDC to BDC d. Air fuel mixture enters through inlet valve and piston moves from TDC to BDCarrow_forwardWhich of the following are not typically found in the block of a modern engine? a. Pistons b. Crankshaft c. Valves d. Oil pumparrow_forwardExplain why a small PCV valve opening is adequate at idle speed.arrow_forward
- Technician A says that you may be able to smell antifreeze from a leaking heater core. Technician B says that you may be able to hear a loose belt when the engine is running. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardAn engine starts and runs briefly after a small quantity of fuel is put into the spark plug hole, but it doesn't not start when fuel is added to the carburetor throat. Tech a says that the problem may be that the exhaust valve is not closing completely due to carbon buildup. Tech b says it may be due to a defective carburetor mounting gasket. Who is correct?arrow_forward1- What is “valve overlap” and how it's affect the performance of the enginearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
The Refrigeration Cycle Explained - The Four Major Components; Author: HVAC Know It All;https://www.youtube.com/watch?v=zfciSvOZDUY;License: Standard YouTube License, CC-BY