Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 31, Problem 5ASRQ
While discussing airflow sensors: Technician A says that with mass airflow and volume airflow sensor systems, if any air bypasses the sensors, the engine will run lean. Technician B says that vacuum leaks in a speed density system will decrease injector pulse width. Who is correct?
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Explain the working of NDIR and chemical sensors of exhaust gas analyzers
In the rotameter (gas flow sensor), rotor friction is greatly increased by water condensation and therefore when mounted on a ventilator or anesthesia machine; insertion is recommended in:A) The inspiratory pathway.B) The expiratory route.C) The escape route.D) B and C
Because modern engines heat up rapidly heated oxygen sensor (ho2s) are not required.
True
False
Chapter 31 Solutions
Automotive Technology
Ch. 31 - List four service precautions for working on the...Ch. 31 - What is indicated by a LTFT reading of 24 percent?Ch. 31 - Describe how testing GDI fuel systems differs from...Ch. 31 - What is the difference between the pulse width and...Ch. 31 - How can you use a dual trace scope to make sure...Ch. 31 - What are three possible problems that can allow...Ch. 31 - What is the purpose of having two accelerator...Ch. 31 - What is indicated by a negative LTFT value?Ch. 31 - What problem may result from dirt buildup on an...Ch. 31 - What is the difference between STFT and LTFT?
Ch. 31 - True or False? The signals from an air-fuel ratio...Ch. 31 - Prob. 2TFCh. 31 - Which of the following is the most likely cause of...Ch. 31 - The PCM checks for a closed throttle plate each...Ch. 31 - Which of the following would not cause a...Ch. 31 - While discussing the causes of...Ch. 31 - While discussing IAC valve diagnosis: Technician A...Ch. 31 - While discussing IAC motor removal, service, and...Ch. 31 - While discussing injector testing: Technician A...Ch. 31 - While discussing airflow sensors: Technician A...Ch. 31 - While discussing scan tool diagnosis of fuel...Ch. 31 - While discussing a high idle speed problem:...Ch. 31 - While discussing the causes of a rich air-fuel...Ch. 31 - While diagnosing an idle speed problem: Technician...Ch. 31 - While looking at fuel trim values: Technician A...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Describe the purpose of having both upstream and downstream oxygen sensors in an exhaust system.arrow_forwardWhich of the following is a likely cause of a lean condition during acceleration and cruising speeds? a. A defective oxygen sensor b. A defective PCM c. A defective ECT sensor d. A defective MAF sensorarrow_forwardTrue or False? An A/F ratio sensor can be tested in the same way as an oxygen sensor.arrow_forward
- What is the correct procedure for checking an oxygen sensor with a DMM?arrow_forwardTrue or False? The signals from an air-fuel ratio sensor are identical to those from a conventional oxygen sensor.arrow_forwardQ 151. the activity of an O2 sensor is best monitered with a ______ . a. scan tool b. logic probe c. noid light d. lab scopearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY