Connect 1 Semester Access Card For Electric Motors And Control Systems
2nd Edition
ISBN: 9781259550195
Author: Petruzella, Frank
Publisher: MCGRAW-HILL HIGHER EDUCATION
expand_more
expand_more
format_list_bulleted
Question
Chapter 3.3, Problem 14RQ
To determine
The value of the current flow in the primary.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
AC power of 100 volts and 1 ampere enters a transformer with 2 coils and exits the transformer with 20 coils. What is the exiting voltage and current?
a.) 1000v/0.1amp
b.) 0.1v/1000amp
c.)1000v/1amp
d.) 2v/20amp
e.) No change
Which of the following is the range of excitating current (in percent) of its rated current for a small distribution transformer?
25
Equal to rated current
6
None of option
OO0O
Describe the four tests carried out on the transformer and state their purpose
Chapter 3 Solutions
Connect 1 Semester Access Card For Electric Motors And Control Systems
Ch. 3.1 - Prob. 1RQCh. 3.1 - a. If 1 MW of electric power is to be transmitted...Ch. 3.1 - Compare the type of AC power normally supplied to...Ch. 3.1 - a. Outline the basic function of a unit...Ch. 3.1 - list three factors taken into account in selecting...Ch. 3.1 - When motors and motor controllers are installed,...Ch. 3.1 - a. What types of conduit raceways are commonly...Ch. 3.1 - Compare the function of a switchboard, panelboard,...Ch. 3.2 - Define the terms primary and secondary as they...Ch. 3.2 - On what basis is a transformer classified as being...
Ch. 3.2 - Explain how the transfer of energy takes place in...Ch. 3.2 - In an ideal transformer, what is the relationship...Ch. 3.2 - A step-down transformer with a Wins ratio of 10:1...Ch. 3.2 - A step-up transformer has a primary current of 32...Ch. 3.2 - What is meant by the term transformer magnetizing,...Ch. 3.2 - Prob. 8RQCh. 3.2 - Prob. 9RQCh. 3.2 - Prob. 10RQCh. 3.2 - The primary of a transformer is rated for 480 V...Ch. 3.2 - A single-phase transformer is rated for 0.5 kVA, a...Ch. 3.3 - Explain the way in which the high-voltage and...Ch. 3.3 - Prob. 2RQCh. 3.3 - Prob. 3RQCh. 3.3 - Prob. 4RQCh. 3.3 - Prob. 5RQCh. 3.3 - Prob. 6RQCh. 3.3 - Prob. 7RQCh. 3.3 - Prob. 8RQCh. 3.3 - Explain the basic difference between the primary...Ch. 3.3 - Prob. 10RQCh. 3.3 - Prob. 11RQCh. 3.3 - Prob. 12RQCh. 3.3 - What important safety precaution should be...Ch. 3.3 - Prob. 14RQCh. 3.3 - The control transformer for an across-the-line...Ch. 3.3 - The two primary windings of a dual-primary control...Ch. 3.3 - Prob. 3TCh. 3.3 - A dry-type general-purpose power transformer is...Ch. 3.3 - A current transformer is to be tested in circuit...Ch. 3.3 - Discuss how electric power might be distributed...Ch. 3.3 - A block of several transformers arc fed from...Ch. 3.3 - How would you proceed with a DC resistance check...Ch. 3.3 - Prob. 5DT
Knowledge Booster
Similar questions
- Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELLarrow_forwardDraw a transformer with a turns ratio of 4:1. The primary source voltage is 480 volts. What size load resistor would be needed to develop a secondary current of 12 amps. What is the primary current and the power used in this transformer?arrow_forwardIn the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. a)Find the average power spent by the load circuit? b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Comment on the results obtained?arrow_forward
- In the T-shaped equivalent circuit of the transformer for the load mode, indicate the resistance in which power will be released, equal to the electrical losses of the secondary winding. Select one: O a. 12 O b.11 O c. Zload O d. l2 O e. Im Clear my choice Which of the listed quantities determines on the substitution circuit the resistance of the magnetization branch Rm Select one: O a. Dol, Do2 O b. Pel - electrical losses O C. Pst - losses in steel O d. K-transformation ratio O e. om - mutual induction flow Clear my choicearrow_forwarda) The transformer has a turns ratio of 9.45, what is the dc load voltage considering the ripple voltage? b) The transformer has a turns ratio of 9.45, what is the dc load voltage without considering the ripple voltage?in 2 decimal places.arrow_forwardQ/What is the benefit of the electrical transformer in the event of a load and in the absence of a load?arrow_forward
- Flag this question for future reference What is the test that can be conducted in the laboratory to understand the transformer impedance drops are dependent on the load current with a variation in the secondary voltage? O a. Direct Load Test O b. Open Circuit Test OC. Voltage Ratio Test O d. Polarity Testarrow_forwardWhat is the type of core material of the transformer? a. Iron O b. Silicon steel O c. Graphite O d. Copperarrow_forwardCurrent transformer has Select one: O a. No relation between primary windings and its secondary windings O b. More secondary windings than its primary windings O C. Primary windings equal to secondary windings O d. More primary windings than its secondary windingsarrow_forward
- Voltage control method connected across the load, to supply part of VAR required is ..... O Shunt capacitor O tap changing transformer O series capacitor O booster transformerarrow_forwardAnswer only please The resistance of a transformer winding is 0.25 ohm at 25oC. When operating at full load, the temperature of the winding is 75oC. The temperature coefficient of resistance for copper at 0oC is 0.00427 per oC. What is the winding resistance at full load? a. 0.512 ohm b. 0.315 ohm c. 0.298 ohm d. 0.271 ohmarrow_forward3.6. A 60-kVA, 4800/2400-V single-phase transformer gave the following test results: 1. Rated voltage is applied to the low voltage winding and the high volt- age winding is open-circuited. Under this condition, the current into the low voltage winding is 2.4 A and the power taken from the 2400 V source is 3456 W. 2. A reduced voltage of 1250 V is applied to the high voltage winding and the low voltage winding is short-circuited. Under this condition, the current flowing into the high voltage winding is 12.5 A and the power taken from the 1250 V source is 4375 W. (a) Determine parameters of the equivalent circuit referred to the high volt- age side. (b) Determine voltage regulation and efficiency when transformer is operat- ing at full-load, 0.8 power factor lagging, and a terminal voltage of 2400 V. (c) What is the load kVA for maximum efficiency and the maximum effi- ciency at 0.8 power factor? (d) Determine the efficiency when transformer is operating at 3/4 full-load, 0.8 power…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Electricity for Refrigeration, Heating, and Air C...Mechanical EngineeringISBN:9781337399128Author:Russell E. SmithPublisher:Cengage Learning
Electricity for Refrigeration, Heating, and Air C...
Mechanical Engineering
ISBN:9781337399128
Author:Russell E. Smith
Publisher:Cengage Learning