AUTOMOTIVE TECHNOLOGY (W/MINDTAP)
7th Edition
ISBN: 9780357096772
Author: ERJAVEC
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 34, Problem 6MC
Which of the following exhaust gases is typically not measured during an I/M 240 test?
a. HC
b. O2
c. NOx
d. CO
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
When performing an engine oil level
check, if additional oil is needed, estimate
the amount by checking the emissions
standards guide to the dipstick markings.
Select one:
True
False
Unburned HC and Carbon mono-oxide reduced in the exhaust gases if the
A/F decreased
True
False
Technician A says that if the oil pressure
shows low on the vehicle's gauge, engine
oil pressure should be verified using a
manual test gauge. Technician B says that
if a vehicle's oil pressure gauge reads too
high, engine oil pressure should be
verified using a manual test gauge. Who is
correct?
Select one:
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
Chapter 34 Solutions
AUTOMOTIVE TECHNOLOGY (W/MINDTAP)
Ch. 34 - A rich air-fuel ratio causes HC emissions to...Ch. 34 - What will result from too little EGR flow? And...Ch. 34 - What can result from a charcoal canister that is...Ch. 34 - What happens if a PCV valve is stuck in the open...Ch. 34 - Explain why the I/M 240 and similar tests are...Ch. 34 - How do you test the efficiency of a secondary AIR...Ch. 34 - List five common causes for high HC emissions.Ch. 34 - Describe carbon monoxide (CO) emissions in...Ch. 34 - An EGR valve that does not fully close can cause...Ch. 34 - A restricted catalytic converter can cause all of...
Ch. 34 - Which of the following statements about EVAP...Ch. 34 - As a catalytic converter begins to deteriorate,...Ch. 34 - How much pressure does a typical EVAP pressure...Ch. 34 - Which of the following exhaust gases is typically...Ch. 34 - Prob. 7MCCh. 34 - While discussing the proper way to test a...Ch. 34 - Prob. 2ASRQCh. 34 - While discussing catalytic converter diagnosis:...Ch. 34 - While discussing EGR valve diagnosis: Technician A...Ch. 34 - While discussing EGR valve diagnosis: Technician A...Ch. 34 - When discussing the diagnosis of a positive back...Ch. 34 - While diagnosing a PCV problem: Technician A says...Ch. 34 - Technician A says that the AIR system should pump...Ch. 34 - While discussing PCV system diagnosis: Technician...Ch. 34 - While discussing EVAP testing: Technician A says...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following is not an effective way to determine if an engine has an internal coolant leak? Performing a pressure test on the system Visually inspecting the exhaust, coolant, and engine oil Using a dye penetrant and black light Using a combustion leak testerarrow_forwardTrue or False? A compression gauge will show the amount of air leaking through a cylinder as a percentage.arrow_forwardTechnician A makes sure that the exhaust system is cool to the touch before working on it. Technician B disconnects the batterys negative cable before welding an exhaust pipe. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
- P Flag question An increase in oil prices will create a situation where consumers will start buying conventional cars. Select one: O a. True O b. False Clear my choicearrow_forwardWhich of the following statements regarding the “Pre-Emission Inspection Check” Of a diesel powered vehicle that is subject to Opacity (Smoke Meter) testing is not true? The governor (if equipped), the exhaust system, and the emissions control devices must all be checked. The exhaust system must be checked for any missing sections which would prevent collection of a valid exhaust sample. Vehicles not meeting requirements cannot be inspected. This is not considered an inspection or rejection and no fee is to be charged. The governor, if originally equipped, must be checked for presence, connection, and operation.arrow_forwardTechnician A uses sandpaper to remove carbon deposits from turbocharger wastegate parts. Technician B scrapes off heavy deposits before attempting to clean the unit. Who is correct?arrow_forward
- Technician A says that if an engine had good results from a compression test, it will have good results from a cylinder leakage test Technician B says that if an engine had good results from a cylinder leakage test, it will have good results from a running compression test Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardHC emissions may come from the tailpipe or sources.arrow_forwardName the three types of stress testing used to test for intermittent ignition component problems and list the procedures for conducting each type of test.arrow_forward
- Which of the following is not a common way to identify the location of cracks in the engine block or cylinder head? Pressure checks Vacuum test Magnetic particle inspection Penetrativearrow_forwardTechnician A says that vacuum hose routing for the entire vehicle is illustrated on the underhood decal. Technician B says that this decal illustrates emission system vacuum hose routing. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardTrue or False? The first step in removing an engine is usually the removal of the intake and exhaust manifolds.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
General Industrial Safety; Author: Jim Pytel;https://www.youtube.com/watch?v=RXtF_vQRebM;License: Standard youtube license