Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 39, Problem 5ASRQ
While diagnosing a noise from a transmission: Technician A says that the noise is caused by something internal if it is most noticeable during a test drive. Technician B says that the noise is caused by the clutch if it disappears when the clutch is disengaged. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
technician a says that an oil-soaked clutch dis can cause clutch chatter technician b says that clutch chatter can be caused by the loose bell housing bolts
when discussing shift problems, technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems. technician b says that poor shift boot alignment can cause a transaxle to jump out of gear
Technician A says that limited- slip differential clutch packs are designed to slip when the vehicle turns a corner. Technician B says that a special additive is placed in the hypoid gear lubricant to promote clutch pack slippage on corners. Who is correct?
Chapter 39 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 39 - After draining gear oil from a transaxie, the...Ch. 39 - Prob. 2RQCh. 39 - Prob. 3RQCh. 39 - What tool is often required to remove gears and...Ch. 39 - When removing or installing bearings, where should...Ch. 39 - List five common sources for transmission fluid...Ch. 39 - True or False? Bearing noise increases under load...Ch. 39 - A rough, growling noise that is heard from a...Ch. 39 - A clicking noise during transrnission/transaxle...Ch. 39 - Worn teeth on a speed gear can cause_______. a....
Ch. 39 - Using a lubricant that is thicker than the...Ch. 39 - What should you do to properly identify the type...Ch. 39 - Prob. 13RQCh. 39 - List at least five items that are typically...Ch. 39 - A poorly adjusted shift linkage can cause which of...Ch. 39 - Technician A says that the transmission rear seal...Ch. 39 - A noise occurs in forward and reverse gears but...Ch. 39 - A rough, growling noise occurs when a vehicle with...Ch. 39 - A car jumps out of gear into neutral, particularly...Ch. 39 - While diagnosing a noise from a transmission:...Ch. 39 - Technician A says that broken or worn engine and...Ch. 39 - While inspecting a transaxies gears: Technician A...Ch. 39 - During a test drive, a noise that appears to be...Ch. 39 - While inspecting the synchronizers of a transaxle:...Ch. 39 - Technician A says that the proper fluid level for...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- When discussing shift problems,Technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems.Technician B says that poor shift boot alignment can cause a transaxle to jump out of gear?arrow_forwardTechnician A says that if the shift for all forward gears is delayed, a slipping forward clutch is normally indicated. Technician B says that a bad forward clutch is indicated when there is a slip when the transmission shifts into any forward gear. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that clutch slippage is most notice-able in higher gears. Technician B says that clutch slip page is not noticeable in lower gears. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- Technician A says that the clutch-style limited slip differential uses a multi-plate clutch pack between each side gear and the differential case. Technician B says that if the clutch discs are worn, rotating torque will be higher than specifications. Who is correct?arrow_forwardThree factors to consider before deciding to apply a transmission of gear drivesarrow_forwardWhile inspecting a planetary gear-type final drive, Technician A says blackened pinion shafts indicate severe overloading. Technician B says bluish gears indicate overheating. Who is correct?arrow_forward
- 4) Explain the importance of a cone clutch with an application.arrow_forwardWhat is the purpose of a clutch in a vehicle transmission system?arrow_forwardA hot-wire MAF has low resistance across it when the wire is hot: Technician A says that this condition will cause the engine to stall as soon as you put the transmission into gear. Technician B says that this condition will cause the transmission to shift late. Who is correct?arrow_forward
- Technician A says a purpose of a lockup piston clutch is to improve fuel economy. Technician B says a lockup piston clutch is designed with a damper assembly to transmit driving torque and absorb shock. Who is correct?arrow_forwardHow does a viscous clutch assembly work? Why is it used in AWD systems?arrow_forwardWhile discussing the purpose of a clutch pressure plate: Technician A says that the pressure plate assembly squeezes the clutch disc onto the flywheel. Technician B says that the pressure plate moves away from the clutch disc so that the disc can stop rotating. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License