Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 39, Problem 7ASRQ
While inspecting a transaxie’s gears: Technician A says that wear on the back of the gear teeth is normal. Technician B says that it is normal for a reverse idler gear to have small chips on its engagement side. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Technician A says that side-bearing preload limits the amount the differential case is able to move laterally in the axle housing. Technician B says that adjusting backlash sets the depths of the mesh between the ring and pinion gears’ teeth. Who is correct?
Tech A says that if a noise is caused by a set of worn gears, it will normally be loudest in that gear while driving under a load. Tech B says that if the bearings on the input shaft, countershaft, or main shaft are worn, either front or rear, a growling noise will result when stopped in gear. Who is correct?
To achieve a slow overdrive in a simple planetary gearset, the .
a.sun gear must be the input member
b.ring gear must be the input member
c.planetary cart"ier must be the input memberring gear must be held
d. ring gear must be held
Chapter 39 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 39 - After draining gear oil from a transaxie, the...Ch. 39 - Prob. 2RQCh. 39 - Prob. 3RQCh. 39 - What tool is often required to remove gears and...Ch. 39 - When removing or installing bearings, where should...Ch. 39 - List five common sources for transmission fluid...Ch. 39 - True or False? Bearing noise increases under load...Ch. 39 - A rough, growling noise that is heard from a...Ch. 39 - A clicking noise during transrnission/transaxle...Ch. 39 - Worn teeth on a speed gear can cause_______. a....
Ch. 39 - Using a lubricant that is thicker than the...Ch. 39 - What should you do to properly identify the type...Ch. 39 - Prob. 13RQCh. 39 - List at least five items that are typically...Ch. 39 - A poorly adjusted shift linkage can cause which of...Ch. 39 - Technician A says that the transmission rear seal...Ch. 39 - A noise occurs in forward and reverse gears but...Ch. 39 - A rough, growling noise occurs when a vehicle with...Ch. 39 - A car jumps out of gear into neutral, particularly...Ch. 39 - While diagnosing a noise from a transmission:...Ch. 39 - Technician A says that broken or worn engine and...Ch. 39 - While inspecting a transaxies gears: Technician A...Ch. 39 - During a test drive, a noise that appears to be...Ch. 39 - While inspecting the synchronizers of a transaxle:...Ch. 39 - Technician A says that the proper fluid level for...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- When a transmission is described as having two planetary gearsets in tandem, what does this mean?arrow_forwardIn a simple planetary gearset, when the planetary carrier is held, the gearset produces a______. a. reverse b. direct drive c. fast overdrive d. forward reductionarrow_forwardWhile discussing a Lepelletier system: Technician A says that two simple planetary gearsets are connected in tandem. Technician B says that these systems rely on various combinations of the planetary gears to obtain many forward gears. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- While inspecting a planetary gear-type final drive, Technician A says blackened pinion shafts indicate severe overloading. Technician B says bluish gears indicate overheating. Who is correct?arrow_forwardWhat TWO main characteristics do idler gears offer when used in a gear system?arrow_forwardWhen discussing the various gear positions of a transfer case, Technician A says that when the transfer case is in low, the overall gear ratio is numerically increased. Technician B says that when the transfer case is in the high position, the vehicle operates in an overdrive mode due to the decrease in torque multiplication. Who is correct?arrow_forward
- Discuss the difference between simple gear train and compound gear train ..arrow_forwardThree factors to consider before deciding to apply a transmission of gear drivesarrow_forwardWhile reviewing the procedure for setting backlash: Technician A says that backlash is adjusted along with side-bearing preload by loosening or tightening side-bearing adjusting nuts. Technician B says that normally, to decrease the amount of backlash, a thin shim is installed on one side of the gear and a thick one on the other side. Who is correct? a Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- Explain the operation principle of a differential system and how a differential system relates to epicyclic gear trainsarrow_forwardCompare the differences between different gear profilesarrow_forwardTechnician A says that a Simpson gearset is two planetary gearsets that share a common sun gear. Technician B says that a Ravigneaux gearset has two sun gears, two sets of planet gears, and a common ring gear. Who is correct? a.Technician A only b.Technician B only c.Both A and B d.Neither A or Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License