HEATING, VENTILATING,+AC ANAL...EBOOK>I<
6th Edition
ISBN: 2819480255750
Author: Mcquiston
Publisher: INTER WILE
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 4, Problem 4.20P
To determine
The number of filter modules required for the air handling system.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A duct system layout is shown in the figure below, it is supplied with air from a
central air conditioning unit. The ducts require to be rectangular with a
maximum height of 10in due to ceiling limitations. Maximum air duct velocities
are: main = 1200fpm; branches = 800 fpm. Determine the sizes of the
rectangular ducts and the static pressure at the AHU. Use Velocity reduction
method.
AHU- AIR HANDLING UNIT (CENTRAL AIRCON)
please solve : A its my home work, thank you very much.
page: 2/8
8. For hydraulic pumps and motors, there are two types of losses, i.e.
9. The measure for oil trapping of gear pumps is
10. Three basic conditions for operation of pumps are
and mechanism to
separate suction from delivery stroke.
11. For the axial piston pump, the pulsation is minimized when the
pump
has
12. In neutral position, the port P and T of relief valves are
(connected/disconnected).
13. The secondary air treatment unit of pneumatic systems include
and air lubricator.
Chapter 4 Solutions
HEATING, VENTILATING,+AC ANAL...EBOOK>I<
Ch. 4 - Using Fig. 4-1, draw a conclusion about the...Ch. 4 - Using Fig. 4-1, draw a conclusion about the...Ch. 4 - Select comfortable summer design conditions (dry...Ch. 4 - It is desired to use a space as a large classroom...Ch. 4 - An indoor tennis facility finds that it has...Ch. 4 - Work Problem 4-5 for an average air speed at court...Ch. 4 - In an occupied space the mean air velocity is...Ch. 4 - An occupied space is being held at 76 F (24 C) and...Ch. 4 - What do you think is the best thermostat setting...Ch. 4 - With the air conditioning running and the...
Ch. 4 - Discuss how an emergency government mandate to set...Ch. 4 - In the heating seasons the heat loss from a...Ch. 4 - Air motion can be good or bad, depending on the...Ch. 4 - To save energy in large, chilled water systems,...Ch. 4 - Overhead fans (Casablanca fans) are often reversed...Ch. 4 - A school classroom is designed for 30 people. (a)...Ch. 4 - Carbon dioxide is being generated in an occupied...Ch. 4 - Each person in a room is assumed to be producing...Ch. 4 - An air-handling system must handle 2000 cfm with a...Ch. 4 - Prob. 4.20PCh. 4 - How many filter modules will be required using the...Ch. 4 - Work Problem 4-21 assuming that the filter is a...Ch. 4 - The M-200, 0.60.60.2 filters of Table 4-3 are to...Ch. 4 - Investigate the feasibility of using 100 percent...Ch. 4 - Work Problem 4-24 but replace the 100 percent...Ch. 4 - Using M-15 filter media and the requirement of 60...Ch. 4 - A filter system is available that will filter out...Ch. 4 - A maximum of 10 smokers are anticipated in a smong...Ch. 4 - Solve Ex. 4-4 assuming that the filter is in...Ch. 4 - Solve Problem 4-28 assuming that the filter is in...Ch. 4 - Fora 3000-ft3 combination and exercise operation,...Ch. 4 - A classroom with a capacity of 225 people is...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- BOOK: FLUID POWER, 3e, JAMES A. SULLIVAN PROBLEM: 13 - 18arrow_forwardProblem 1-22. A portion of a well is to be drilled from depth A to depth B with the following requirements: Minimum flow rate = 240 gpm Maximum flow rate = 660 gpm The pump is a single-acting triplex pump with the following specifications: Maximum delivery pressure = 3,400 psi Hydraulic horsepower = 800 hp Volumetric efficiency = 80% for spm less than 50 and 70% for spm greater than 50 %3D %3D Specify the liner size that should be used to drill that portion of hole.arrow_forwardDetermine the pressure drop over a reducer with the following conditions: Fluid density: 25 kg/m3Fluid velocity: 1.5 m/sFluid viscosity: 0.001 Pa*sInlet diameter: 0.12 mOutlet diameter: 0.019 mPipe absolute roughness: 4e-4 m Give your final answer in Pa, rounded to the nearest whole number. [Ignore entrance/exit losses and velocity loss terms]arrow_forward
- he night-time chilled water system is not a closed loop system, meaning that some amount of water is lost due to evaporation every night. If it is 96% efficient (i.e. 4% of the water flow rate is dispersed to the outdoor air and needs to be replaced), how much make up water does it need to draw from the municipal water supply daily (in gallons)? Round to nearest integer. (Given: Qheat loss = 1,500,000 Btu) Total gallons in water tank: 1500 gallons//system runs: 10 hoursarrow_forwardQ: Design the duct system by using velocity reduction method and find FTP and the amount of dampering required. Assume a dynamic loss coefficient of 0.3 for downstream and 0.5 for upstream to branch and for the elbow. The dynamic loss coefficients for the outlets may be taken as 1.0. 1m'/s 10 m 2 m /s 30 m 9 m/s FAN 30 m 45 m 10 m 1m /sarrow_forwardSolve itarrow_forward
- Q: Design the duct system by using velocity reduction method and of dampering required. Assume dynamic loss coefficient of 0.3 for downstream and 0.5 for branch and for the elbow. The dynamic loss find FTPmax and the amount a upstream to coefficients for the outlets may be taken as 1.0. 1m /s 10 m 2m3 /s 30 m 9 m/s FAN 30 m 45 m 10 m 1m /sarrow_forwardNeed in 20 minsarrow_forwardApply the grid method. A motor is being to used to turn the shaft of a centrifugal pump. Apply the equation shown in the image below to calculate the power in watts corresponding to a torque of 100 lbf-in and a rotation speed of 850 rpm.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning