AUTOMOTIVE TECHNOLOGY TECH MANUAL
7th Edition
ISBN: 9781337794220
Author: ERJAVEC
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 40, Problem 10ASRQ
While reviewing the procedure for setting backlash: Technician A says that backlash is adjusted along with side-bearing preload by loosening or tightening side-bearing adjusting nuts. Technician B says that normally, to decrease the amount of backlash, a thin shim is installed on one side of the gear and a thick one on the other side. Who is correct?
a Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Technician A says that side-bearing preload limits the amount the differential case is able to move laterally in the axle housing. Technician B says that adjusting backlash sets the depths of the mesh between the ring and pinion gears’ teeth. Who is correct?
While inspecting a planetary gear-type final drive, Technician A says blackened pinion shafts indicate severe overloading. Technician B says bluish gears indicate overheating. Who is correct?
Pinion gear-to-flywheel ring gear clearance is beingdiscussed: Technician A says that if there is too muchclearance, there will be a high pitch while the enginecranks. Technician B says that if there is too littleclearance, there will be a high pitch noise after theengine is started. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor B
Chapter 40 Solutions
AUTOMOTIVE TECHNOLOGY TECH MANUAL
Ch. 40 - Prob. 1SACh. 40 - What type of axle housing resembles a banjo?Ch. 40 - What type of axle merely supports the vehicle load...Ch. 40 - What type of floating axle has one wheel bearing...Ch. 40 - How are problems normally first noticed with the...Ch. 40 - In front-wheel drivetrains, the CV joint nearer...Ch. 40 - A CV joint that is capable of in-and-out movement...Ch. 40 - The double-offset joint is typically used in...Ch. 40 - Which type of joint has a flatter design than any...Ch. 40 - Which of these is the best way to determine which...
Ch. 40 - The single Cardan/Spicer universal joint is also...Ch. 40 - The drive shaft component that provides a means of...Ch. 40 - Large cars with long drive shafts often use a...Ch. 40 - Which type of driving axle supports the weight of...Ch. 40 - Which of the following describes the double-Cardan...Ch. 40 - Technician A says that a gear tooth pattern...Ch. 40 - Technician A says that limited-slip differential...Ch. 40 - Technician A says that side-bearing preload limits...Ch. 40 - Technician A says that a hunting gearset is one in...Ch. 40 - While discussing the possible causes for a...Ch. 40 - While diagnosing the cause of a clicking noise...Ch. 40 - Prob. 7ASRQCh. 40 - Technician A says that when a car is moving...Ch. 40 - While discussing different types of ring and...Ch. 40 - While reviewing the procedure for setting...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- when checking or setting the backlash it is important to have the dial indicator tip in the correct place on the ring gear. where should the tip contact the ring geararrow_forwardWhen discussing the possible causes for a shudder during acceleration, Technician A says that a worn inner CV joint could be the cause. Technician B says that insufficient differential gear backlash could be the cause of the problem. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor Barrow_forwardChoose the correct device pair from the following which is a common example for lower pair and self-closed pair. a. Roller and rings of bearing. b. Cam and follower. c. Gear mesh with another gear. d. Nut and bolt.arrow_forward
- Gears and crankshaft are transmitting type of short distance power type of transmission. Select one: True Falsearrow_forwardTechnician A says that a hunting gearset is one in which one drive pinion gear tooth contacts only certain ring gear teeth, Technician B says that a partial nonhunting gearset is one in which one pinion tooth contacts only six ring gear teeth. Who is correct?arrow_forwardTechnician A says that a Simpson gearset is two planetary gearsets that share a common sun gear. Technician B says that a Ravigneaux gearset has two sun gears, two sets of planet gears, and a common ring gear. Who is correct? a.Technician A only b.Technician B only c.Both A and B d.Neither A or Barrow_forward
- From the following identify a true statement regarding the adjustment of drive belt tension. a. Less than 8 mm should be the correct a deflection for each belt which is under tension b. More than 6 mm should be the correct a deflection for each belt which is under tension c. More than 8 mm should be the correct a deflection for each belt which is under tension. d. More than 6 mm and less than 8 mm should be the correct a deflection for each belt which is under tension.arrow_forwardWhich of the following screwdrivers is like a Phillipsbut has a flatter and blunter tip?a. Standardb. Torx®c. Pozidriv®d. Clutch headarrow_forwardWhich of the following is the most likely cause for a shudder during the engagement of a lock-up torque converter? a. A bad converter b. Worn or damaged CV or U-joints c. A worn front planetary gearset d. Loose flexplatearrow_forward
- A noise occurs in forward and reverse gears but not in neutral: Technician A says that the input shaft bearing may be bad. Technician B says that the mainshaft bearing may be bad. Who is correct? a. Technician A only b. Technician B only c. Both Aand B d. Neither A nor Barrow_forwardchoose true or false :-The speed of the sprocket reduces as the chain pitch increases for a given number of teeth.arrow_forwardTechnician A says that a hunting gearset is one inwhich one drive pinion gear tooth contacts only certainring gear teeth. Technician B says that a partialnonhunting gearset is one in which one pinion toothcontacts only six ring gear teeth. Who is correct?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
BEARINGS BASICS and Bearing Life for Mechanical Design in 10 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=aU4CVZo3wgk;License: Standard Youtube License