AUTOMOTIVE TECH - W/ TECH MAN. + MINDTA
7th Edition
ISBN: 9780357474723
Author: ERJAVEC
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Question
thumb_up100%
Chapter 40, Problem 1SA
To determine
The three ways for classification of CV joints.
Expert Solution & Answer
Answer to Problem 1SA
The three ways for classification are by position, by design and by function.
Explanation of Solution
The CV joints are classified in three ways which are:
- By Position − inboard or outboard.
- By Design − ball-type or tripod.
- By Function − fixed or plunge.
Conclusion:
Thus, these are the three classifications of CV joints.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
explain the operational difference between CV joints and universal joints. (50-80 words)
Define the following,Joint.Link.Joint space.Actuator space.
List the pros and cons of a compression spring ping pong ball launcher
Chapter 40 Solutions
AUTOMOTIVE TECH - W/ TECH MAN. + MINDTA
Ch. 40 - Prob. 1SACh. 40 - What type of axle housing resembles a banjo?Ch. 40 - What type of axle merely supports the vehicle load...Ch. 40 - What type of floating axle has one wheel bearing...Ch. 40 - How are problems normally first noticed with the...Ch. 40 - In front-wheel drivetrains, the CV joint nearer...Ch. 40 - A CV joint that is capable of in-and-out movement...Ch. 40 - The double-offset joint is typically used in...Ch. 40 - Which type of joint has a flatter design than any...Ch. 40 - Which of these is the best way to determine which...
Ch. 40 - The single Cardan/Spicer universal joint is also...Ch. 40 - The drive shaft component that provides a means of...Ch. 40 - Large cars with long drive shafts often use a...Ch. 40 - Which type of driving axle supports the weight of...Ch. 40 - Which of the following describes the double-Cardan...Ch. 40 - Technician A says that a gear tooth pattern...Ch. 40 - Technician A says that limited-slip differential...Ch. 40 - Technician A says that side-bearing preload limits...Ch. 40 - Technician A says that a hunting gearset is one in...Ch. 40 - While discussing the possible causes for a...Ch. 40 - While diagnosing the cause of a clicking noise...Ch. 40 - Prob. 7ASRQCh. 40 - Technician A says that when a car is moving...Ch. 40 - While discussing different types of ring and...Ch. 40 - While reviewing the procedure for setting...
Knowledge Booster
Similar questions
- materials used in friction clutch designarrow_forward(1)Explain all the parameters that will be helpful to make driveshaft more efficient and lightweight.arrow_forwardLabel all links starting with "1" and all joints starting with "A". Include whether the joint is a half joint or full joint as well as the type of joint.arrow_forward
- Where and why do we use Overrunning clutches? Explain its constructional featuresand working in the starting drivearrow_forwardSection angle of V-belt in belt drive φ=40˚,In order to make good contact and increase friction, thepulley groove angle should be_____. A.Slightly greater than 40˚ B.Slightly less than 40˚C.Equal to 40˚ .D.Equal to 90˚ (please explain it too)arrow_forwardThe length of threading on a BX box connector is approximately 7/16 inch. The locknut is 1/8 inch thick, and the metal into which this connector is inserted is 3/32 inch. How much threading is left for a threaded bushing?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningUnderstanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning