Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 40, Problem 6RQ
In front-wheel drivetrains, the CV joint nearer the transaxle is the____.
a. inner joint
b. inboard joint
c. outboard joint
d. both a and b
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
The typical RWD drive shaft rotates how many times faster than wheels
Which type of driving axle supports the weightof the vehicle?a. Semifloatingb. Three-quarter floatingc. Full-floatingd. None of the above
what are the mechanical differences between 4 wheel drive, front wheel drive and rear wheel drive systems?
Chapter 40 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 40 - Prob. 1RQCh. 40 - What type of axle housing resembles a banjo?Ch. 40 - What type of axle merely supports the vehicle load...Ch. 40 - What type of floating axle has one wheel bearing...Ch. 40 - How are problems normally first noticed with the...Ch. 40 - In front-wheel drivetrains, the CV joint nearer...Ch. 40 - A CV joint that is capable of in-and-out movement...Ch. 40 - The double-offset joint is typically used in...Ch. 40 - Which type of joint has a flatter design than any...Ch. 40 - Which of these is the best way to determine which...
Ch. 40 - The single Cardan/Spicer universal joint is also...Ch. 40 - The drive shaft component that provides a means of...Ch. 40 - Large cars with long drive shafts often use a...Ch. 40 - Which type of driving axle supports the weight of...Ch. 40 - Which of the following describes the double-Cardan...Ch. 40 - Technician A says that a gear tooth pattern...Ch. 40 - Technician A says that limited-slip differential...Ch. 40 - Technician A says that side-bearing preload limits...Ch. 40 - Technician A says that a hunting gearset is one in...Ch. 40 - While discussing the possible causes for a...Ch. 40 - While diagnosing the cause of a clicking noise...Ch. 40 - Prob. 7ASRQCh. 40 - Technician A says that when a car is moving...Ch. 40 - While discussing different types of ring and...Ch. 40 - While reviewing the procedure for setting...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The four common configurations used as the final drives on FWD vehicles are the_____ gear,_____ gear,_______gear, and_____.arrow_forwardWhich characteristic is common to all four-wheel-drive vehicles? They use a differential at both axles. They use CV joints at the front axle. They use a centre differential.arrow_forward32. Technician A says hypoid gearset are only used in RWD vehicle drivetrains. Technician B says hypoid gearset multiply torque. Which technician is correct? A- Technician A B- Technician B C- Both A and B D- Neither A nor B.arrow_forward
- Which of the following is the most likely cause for a shudder during the engagement of a lock-up torque converter? a. A bad converter b. Worn or damaged CV or U-joints c. A worn front planetary gearset d. Loose flexplatearrow_forwardWhich of the following is probably not the cause of a vibrating clutch? a. Excessive crankshaft end play b. Out-of-balance pressure plate assembly c. Excessive flywheel runout d. Loose flywheel boltsarrow_forwardWhat is open belt drive?arrow_forward
- Which type of driving axle supports the weight of the vehicle? a. Semifloating b. Three-quarter floating c. Full-floating d. None of the abovearrow_forwardWhich of the following is a good definition of SAI? Forward tilt of the top of the steering knuckle Inward tilt of the spindle steering arm Inward tilt of the top of the ball joint or strut Outward tilt of the top of the ball joint or strutarrow_forwardWhich of the following is part of the sprung weight of a vehicle? a. Steering linkage b. Tires c. Engine d. All of the abovearrow_forward
- How is the speed of gearless traction elevator drive mechanisms varied?arrow_forwardIn a planetary arrangement transfer case, what is the driven member in 4LO? carrier sun direct clutch ringarrow_forwardTechnician A says the front wheel bearings on a typical FWD car are sealed and non-adjustable. Technician B says the front wheel bearings on a typical FWD car are greaseable and adjustable. Who is correct?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License