Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 40, Problem 6ASRQ
While diagnosing the cause of a clicking noise that is heard only when the car is turning: Technician A says that the most probable cause is a worn wheel bearing. Technician B says that the most probable cause is a worn outboard CV joint. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
When discussing shift problems,Technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems.Technician B says that poor shift boot alignment can cause a transaxle to jump out of gear?
When adjusting a vehicle to counter the effect of road crown, what is the adjustment would you make-Adjust the left front wheel with slightly less positive caster-Adjust the right front wheel with slightly less positive caster-Adjust the right front wheel with slightly more positive camber-Adjust both front wheels with slight toe-out
Technician A says that on most vehicles, the wheel/tire assembly is considered sprung weight . Technician B says that low unsprung weight makes the vehicle handle better on irreg ular surfaces. Who is correct?
Chapter 40 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 40 - Prob. 1RQCh. 40 - What type of axle housing resembles a banjo?Ch. 40 - What type of axle merely supports the vehicle load...Ch. 40 - What type of floating axle has one wheel bearing...Ch. 40 - How are problems normally first noticed with the...Ch. 40 - In front-wheel drivetrains, the CV joint nearer...Ch. 40 - A CV joint that is capable of in-and-out movement...Ch. 40 - The double-offset joint is typically used in...Ch. 40 - Which type of joint has a flatter design than any...Ch. 40 - Which of these is the best way to determine which...
Ch. 40 - The single Cardan/Spicer universal joint is also...Ch. 40 - The drive shaft component that provides a means of...Ch. 40 - Large cars with long drive shafts often use a...Ch. 40 - Which type of driving axle supports the weight of...Ch. 40 - Which of the following describes the double-Cardan...Ch. 40 - Technician A says that a gear tooth pattern...Ch. 40 - Technician A says that limited-slip differential...Ch. 40 - Technician A says that side-bearing preload limits...Ch. 40 - Technician A says that a hunting gearset is one in...Ch. 40 - While discussing the possible causes for a...Ch. 40 - While diagnosing the cause of a clicking noise...Ch. 40 - Prob. 7ASRQCh. 40 - Technician A says that when a car is moving...Ch. 40 - While discussing different types of ring and...Ch. 40 - While reviewing the procedure for setting...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While diagnosing the cause of wheel shimmy: Technician A says that this problem can be caused by loose wheel bearings. Technician B says that this can be caused by binding steering column U-joints. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that on FWD vehicles, the front wheels toe-out while the rear wheels on an independent suspension try to toe-in as the vehicle moves ahead. Technician B says that on RWD vehicles, the front wheels tend to toe-in while the rear wheels toe-out in response to rolling resistance as suspension compliance. Who is correct?arrow_forwardTechnician A says that the front bearing assembly locknuts for RWD vehicles are typically heavily torqued to maintain the bearing adjustment. Technician B says that the axle nuts for FWD wheel bearing assembly is often staked in place to maintain its specified torque. Who is correct?arrow_forward
- The clutch friction disc always rotates with thearrow_forwardAll of the following are functions of the flywheel, except it ____ . a. provides a mounting place for the clutch assembly b. smooths out cylinder firing pulsations c. has marks used to set the valve timing d. meshes with the starter drive geararrow_forwardMom and vibrations c) Explain why the wheel/tire balancing is necessary.arrow_forward
- When checking the fifth wheel, coupling device, the Certified Inspector must check the condition and the mounting to the frame. True or False?arrow_forwardWhile discussing the fail-safe function: Technician A says that the 4WS indicator light is illuminated during the fail-safe function. Technician B says that the rear wheels steer normally when the 4WS control unit enters the fail-safe mode. Who is correct?arrow_forwardWhile discussing front-wheel caster: Technician A says that excessive positive caster increases the steering effort and causes harsh riding. Technician B says that excessive negative caster causes front-wheel shimmy. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forward
- Which of the following is a good definition of SAI? Forward tilt of the top of the steering knuckle Inward tilt of the spindle steering arm Inward tilt of the top of the ball joint or strut Outward tilt of the top of the ball joint or strutarrow_forwardDefine dynamic and static wheel balance.arrow_forwardTechnician A says that play in the steering gear is the probable cause of a shimmy. Technician B says that it could be loose steering linkage. Who is correct?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License