Fox And Mcdonald's Introduction To Fluid Mechanics
9th Edition
ISBN: 9781118921876
Author: Pritchard, Philip J.; Leylegian, John C.; Bhaskaran, Rajesh
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 5, Problem 27P
To determine
The stream function and the location of streamlines at one-quarter and one-half of the total flow rate.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Consider steady, incompressible, laminar, fully developed, planar Poiseuille flow between two parallel, horizontal plates (velocity and pressure profiles are shown in Fig. At some horizontal location x = x1, the pressure varies linearly with vertical distance z, as sketched. Choose an appropriate datum plane (z = 0), sketch the profile of modi fied pressure all along the vertical slice, and shade in the region representing the hydrostatic pressure component. Discuss.
Consider steady, incompressible, parallel, laminar flow of a film of oil falling slowly down an infinite vertical wall. The oil film thickness is h, and gravity acts in the negative z-direction. There is no applied (forced) pressure driving the flow—the oil falls by gravity alone., except for the case in which the wall is inclined at angle ?. Generate expressions for both the pressure and velocity fields. As a check, make sure that your result agrees with that of when ? = 90°. [Hint: It is most convenient to use the (s, y, n) coordinate system with velocity components (us, ?, un), where y is into the page in Fig. Plot the dimensionless velocity profile us* versus n* for the case in which ? = 60°.]
From the laminar boundary layer the velocity distributions given below, find the momentum thickness θ, boundary layer thickness δ, wall shear stress τw, skin friction coefficient Cf , and displacement thickness δ*1. A linear profile, u(x, y) = a + by
2. von K ́arm ́an’s second-order, parabolic profile,u(x, y) = a + by + cy2
3. A third-order, cubic function,u(x, y) = a + by + cy2+ dy3
4. Pohlhausen’s fourth-order, quartic profile,u(x, y) = a + by + cy2+ dy3+ ey4
5. A sinusoidal profile,u = U sin (π/2*y/δ)
Chapter 5 Solutions
Fox And Mcdonald's Introduction To Fluid Mechanics
Ch. 5 - Which of the following sets of equations represent...Ch. 5 - Which of the following sets of equations represent...Ch. 5 - In an incompressible three-dimensional flow field,...Ch. 5 - In a two-dimensional incompressible flow field,...Ch. 5 - The three components of velocity in a velocity...Ch. 5 - The x component of velocity in a steady,...Ch. 5 - The y component of velocity in a steady...Ch. 5 - The velocity components for an incompressible...Ch. 5 - The radial component of velocity in an...Ch. 5 - A crude approximation for the x component of...
Ch. 5 - A useful approximation for the x component of...Ch. 5 - A useful approximation for the x component of...Ch. 5 - For a flow in the xy plane, the x component of...Ch. 5 - Consider a water stream from a jet of an...Ch. 5 - Which of the following sets of equations represent...Ch. 5 - For an incompressible flow in the r plane, the r...Ch. 5 - A viscous liquid is sheared between two parallel...Ch. 5 - A velocity field in cylindrical coordinates is...Ch. 5 - Determine the family of stream functions that...Ch. 5 - The stream function for a certain incompressible...Ch. 5 - Determine the stream functions for the following...Ch. 5 - Determine the stream function for the steady...Ch. 5 - Prob. 23PCh. 5 - A parabolic velocity profile was used to model...Ch. 5 - A flow field is characterized by the stream...Ch. 5 - A flow field is characterized by the stream...Ch. 5 - Prob. 27PCh. 5 - A flow field is characterized by the stream...Ch. 5 - In a parallel one-dimensional flow in the positive...Ch. 5 - Consider the flow field given by V=xy2i13y3j+xyk....Ch. 5 - Prob. 31PCh. 5 - The velocity field within a laminar boundary layer...Ch. 5 - A velocity field is given by V=10ti10t3j. Show...Ch. 5 - The y component of velocity in a two-dimensional,...Ch. 5 - A 4 m diameter tank is filled with water and then...Ch. 5 - An incompressible liquid with negligible viscosity...Ch. 5 - Sketch the following flow fields and derive...Ch. 5 - Consider the low-speed flow of air between...Ch. 5 - As part of a pollution study, a model...Ch. 5 - As an aircraft flies through a cold front, an...Ch. 5 - Wave flow of an incompressible fluid into a solid...Ch. 5 - A steady, two-dimensional velocity field is given...Ch. 5 - A velocity field is represented by the expression...Ch. 5 - A parabolic approximate velocity profile was used...Ch. 5 - A cubic approximate velocity profile was used in...Ch. 5 - The velocity field for steady inviscid flow from...Ch. 5 - Consider the incompressible flow of a fluid...Ch. 5 - Consider the one-dimensional, incompressible flow...Ch. 5 - Expand (V)V in cylindrical coordinates by direct...Ch. 5 - Determine the velocity potential for (a) a flow...Ch. 5 - Determine whether the following flow fields are...Ch. 5 - The velocity profile for steady flow between...Ch. 5 - Consider the velocity field for flow in a...Ch. 5 - Consider the two-dimensional flow field in which u...Ch. 5 - Consider a flow field represented by the stream...Ch. 5 - Fluid passes through the set of thin, closely...Ch. 5 - A two-dimensional flow field is characterized as u...Ch. 5 - A flow field is represented by the stream function...Ch. 5 - Consider the flow field represented by the stream...Ch. 5 - Consider the flow field represented by the stream...Ch. 5 - Consider the velocity field given by V=Ax2i+Bxyj,...Ch. 5 - Consider again the viscometric flow of Example...Ch. 5 - The velocity field near the core of a tornado can...Ch. 5 - A velocity field is given by V=2i4xjm/s. Determine...Ch. 5 - Consider the pressure-driven flow between...Ch. 5 - Consider a steady, laminar, fully developed,...Ch. 5 - Assume the liquid film in Example 5.9 is not...Ch. 5 - Consider a steady, laminar, fully developed...Ch. 5 - Consider a steady, laminar, fully developed...Ch. 5 - A linear velocity profile was used to model flow...Ch. 5 - A cylinder of radius ri rotates at a speed ...Ch. 5 - The velocity profile for fully developed laminar...Ch. 5 - Assume the liquid film in Example 5.9 is...Ch. 5 - The common thermal polymerase chain reaction (PCR)...Ch. 5 - A tank contains water (20C) at an initial depth y0...Ch. 5 - For a small spherical particle of styrofoam...Ch. 5 - Use Excel to generate the progression to an...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A viscous incompressible liquid of density p and of dynamic viscosity n is carried upwards against gravity with the aid of moving side walls. This laminar flow is steady and fully developed in z-direction and there is no applied pressure gradient. The coordinate is fixed in the midway between the walls as shown below. 2d g=-gk liquid P, n x=-d x=d I. The velocity profile in z-direction is pg w(x) = (x2 – d) + U. 2n II. To be able to carry a net amount of liquid upwards, the wall velocities need to be greater than pgd²/(2n). III. If one of the walls stops, increasing the speed of the other wall to 3/2U would carry the same amount of liquid upwards. Which of the above statements are true?arrow_forwardProblem 1: Write the boundary conditions for the following flows: a) Flow between parallel plates (Fig. 1) without a pressure gradient. The upper plate is moving with velocity V. y = +h y = -h Fixed Fig. 1 V u(y)arrow_forwardTwo free vortices of equal strength. but opposite direction of rotation, are superimposed with a uniform flow as shown in Fig. 4 1. The stream functions for these two vorticies are V = -[±T/2#)] In r. (a) Develop an equation for the x-component of velocity, u, at point P(x,y) in terms of Cartesian coordinates x and y. (b) Compute the x-component of velocity at point A and show that it depends on the ratio I'/H. 4- Sketch and describe the flow then determine the stagnation points. •Plx, y) Figure (4)arrow_forward
- Problem 4: Vorticity of flow A two-dimensional velocity is given by the equation: v = 6yi +6xj Is the flow rotational or irrotational? Show the details of your work for full credit.arrow_forward1- Reynolds number is a dimensionless number represent .....to .. 2- The velocity profile of the flow between two parallel plates is linear if the pressure gradient equal and parabolic if the pressure gradient has a .... 3- In the sink and source flow the potential function is represented as.. ...... and the stream function is represented as **** 4- In the laminar boundary layer, the .............. is the dominant reason for the loss while in turbulent boundary layer the is dominant. 5- For inviscid flow, there are no shear stresses the only forces acting on a fluid element are ....... and. *****arrow_forwardConsider the flow field V = (ay+dx)i + (bx-dy)j + ck, where a(t), b(t), c(t), and d(t) are time dependent coefficients. Prove the density is constant following a fluid particle, then find the pressure gradient vector gradP, Γ for a circular contour of radius R in the x-y plane (centered on the origin) using a contour integral, and Γ by evaluating the Stokes theorem surface integral on the hemisphere of radius R above the x-y plane bounded by the contour.arrow_forward
- Oil flows between two very long parallel plates, separated from H, with width b. The bottom plate moves with speed U and is isolated. The upper plate is at rest and receives heat from the environment at a rate equal to qs". Consider laminar flow, thermally developed. Due to the high viscosity of the fluid, viscous dissipation is relevant U isolada 1 - Estimate the velocity profile considering the null pressure gradient and determine the average speed. 2. Determine dissipation per volume unit. 3. Set mixing temperature and determine the mixing temperature variation over the plates.arrow_forwardConverging duct flow is modeled by the steady, two- dimensional velocity field V = (u, v) = (U₁ + bx) i-by. For the case in which Ug = 3.56 ft/s and b = 7.66 s¯¹, plot several streamlines from x = 0 ft to 5 ft and y=-2 ft to 2 ft. Be sure to show the direction of the streamlines. (Please upload you response/solution using the controls provided below.)arrow_forwardConsider a two-dimensional flow which varies in time and is defined by the velocity field, u = 1 and v = 2yt. Compute the convective derivative of each velocity component: Du/Dt and Dv/Dt.arrow_forward
- P1 A thin layer of water flows down a plate inclined to the horizontal with an angle a = 15° in the shown coordinate system. If the thickness of the water layer is a=0.5 mm, assuming that the flow is laminar and incompressible, (water density p = 1000 kg/m³viscosity µ = 0.001 Pa.s and acceleration of gravity g = 9.81 m/s²) and an air flow shears the layer in a direction opposite to its flow with a shear stress of 1 N /m². Solve the Navier-Stokes equation: air water (a) to find the value of the maximum water velocity in m/s to three decimal points, Answer: (b)and to find the value of water velocity at the layer's surface in m/s to three decimal points, Answer:arrow_forwardProblem 3: Obtaining the stream function from velocity components The steady state, incompressible flow field for two-dimensional flow is given by th velocity components: v = 16 y - x and v = 16x+y %3D %3D Determine the equation for the stream function and make sure continuity is satisfiearrow_forwardA common flow encountered in practice is the crossflow of a fluid approaching a long cylinder of radius R at a free stream speed of U∞. For incompressible inviscid flow, the velocity field of the flow is given as in fig. Show that the velocity field satisfies the continuity equation, and determine the stream function corresponding to this velocity field.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Thermodynamics - Chapter 3 - Pure substances; Author: Engineering Deciphered;https://www.youtube.com/watch?v=bTMQtj13yu8;License: Standard YouTube License, CC-BY