Concept explainers
The following laboratory tests are performed on aggregate samples:
a. Specific gravity and absorption
b. Soundness
c. Sieve analysis test
What are the significance and use of each of these tests?
Learn your wayIncludes step-by-step video
Chapter 5 Solutions
Materials For Civil And Construction Engineers In Si Units
Additional Engineering Textbook Solutions
Foundation Design: Principles and Practices (3rd Edition)
Mechanics of Materials (10th Edition)
Web Development and Design Foundations with HTML5 (9th Edition) (What's New in Computer Science)
Java: An Introduction to Problem Solving and Programming (8th Edition)
Elements of Chemical Reaction Engineering (5th Edition) (Prentice Hall International Series in the Physical and Chemical Engineering Sciences)
Starting Out with Java: From Control Structures through Objects (7th Edition) (What's New in Computer Science)
- A sieve analysis test was performed on a sample of coarse aggregate and produced the following results:A.) Calculate the fineness modulus of aggregate? Is in within the typical range?arrow_forwardSieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results: a. Calculate the percent passing through each sieve.b. Plot the percent finer in a semi-log gradation chart.c. What is the maximum aggregate size of the sample?d. What is the nominal maximum aggregate size of the sample?e. What is the fineness modulus? Is it in typical range?arrow_forwardA sieve analysis test was performed on a sample of aggregate and produced the results shown in Table .Calculate the percent passing through each sieve. Plot the percent passingversus sieve size on:a. a semilog gradation chart, andb. a 0.45 gradation chart (Figure A.25).What is the maximum size? What is the nominal maximum size?arrow_forward
- A sieve analysis test was conducted for sample of fine aggregate and obtained theresults as shown in Table Q1. Calculate the percent passing of each sieve and classifythe fineness of fine aggregate based on fineness modulus analysis.arrow_forwardThe mass of aggregate B has been reduced and weighed to conduct an aggregate test shown in Table 2. (e) Calculate the: (iii)apparent specific gravity, and the (iv) aggregate absorption.arrow_forwardTEST PROCEDURE: 1. Dry the aggregate test sample to a constant weight at a temperature of 110 ± 5°C, then cool to room temperature. 2. Select suitable sieve sizes to furnish the information required by the specifications covering the material to be tested. Common sieves in millimeters are 37.5, 25, 19, 12.5, 9.5, 4.75, 2.36, 1.18, 0.6, 0.3, 0.15, and 0.075 mm (11 2 in., 1 in., 3 4 in., 1 2 in., 3 8 in., No. 4, No. 8, No. 16, No. 30, No. 50, No. 100, and No. 200). 3. Nest the sieves in order of decreasing size of opening, and place the aggregate sample on the top sieve. 4. Agitate the sieves by hand or by mechanical apparatus for a sufficient period. The criterion for sieving time is that, after completion, not more than 1% of the residue on any individual sieve will pass that sieve during 1 minute of continuous hand sieving. 5. Determine the weight of each size increment. 6. The total weight of the material after sieving should be compared with the original weight of the sample placed…arrow_forward
- Table shows the grain size distributions of aggregates A, and B. Answer the following questions and show all calculations: What are the maximum sizes of aggregates A and B?arrow_forward500 gm oven dry fine aggregate was tested to find its physical properties. The output from the test was as follows: SSD = 510 gm, mass of the vessel full of water = 1200 gm, mass of vessel plus sand and topped up with water= 1500 gm, mass in wet condition 518 gm, Apparent specific gravity= 2.5 . The grading of the fine aggregate is in the table below. Answer the followings: 1-Moisture content % is 2- The mass of oven dried sand isarrow_forwardWhat are the main purposes of Sieve Analysis of aggregates? Discuss FIneness Modulus What are the differences between coarse aggregates coming from processing plants and coarse aggregates obtained under water in rivers? What is Gradation? What is Effective size?arrow_forward
- The mass of fine aggregate B has been reduced and weighed to conduct an aggregate test shown in Table 2. (e) Calculate the dry bulk specific gravity, SSD bulk specific gravity, apparent specific gravity, and the aggregate absorption.arrow_forwardFine aggregate sample was tested to find its physical properties. The test results were as follows: Bulk specific gravity= 2.42, Apparent specific gravity= 2.58, mass of the vessel full of water = 1350 gm, mass of the vessel plus sand and topped up with water= 1600 gm, mass in wet condition 541 gm. Calculate 1- absorption% 2- moisture content% 3- Bulk density 4- Apparent densityarrow_forwardA sieve analysis test was performed on a sample of coarse aggregate and produced the results in Tablea. Calculate the percent passing through each sieve.b. What is the maximum size?c. What is the nominal maximum size?d. Plot the percent passing versus sieve size on a semilog gradation chart.e. Plot the percent passing versus sieve size on a 0.45 gradation chart.f. Referring to Table (ASTM C33), what is the closest size number anddoes it meet the gradation for that standard size?arrow_forward
- Structural Analysis (10th Edition)Civil EngineeringISBN:9780134610672Author:Russell C. HibbelerPublisher:PEARSONPrinciples of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
- Fundamentals of Structural AnalysisCivil EngineeringISBN:9780073398006Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel LanningPublisher:McGraw-Hill EducationTraffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage Learning