Materials For Civil And Construction Engineers In Si Units
4th Edition
ISBN: 9781292154404
Author: Michael S Mamlouk
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 5, Problem 5.28QP
Three aggregates are to be mixed together in the following ratio:
Aggregate A: 35%
Aggregate B: 40%
Aggregate C: 25%
For each aggregate, the percent passing a set of five sieves is shown in Table P5.28.
Determine the percent passing each sieve for the blended aggregate.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Three aggregates are to be mixed together in the following ratio:Aggregate A: 35%Aggregate B: 40%Aggregate C: 25%For each aggregate, the percent passing a set of five sieves is shown in Table PDetermine the percent passing each sieve for the blended aggregate.
"A sieve analysis test was performed on a sample of fine aggregate and produced the following results:Sieve, mm 4.75 2.36 2.00 1.18 0.60 0.30 0.15 0.075 pan.Amount retained, g 0 33.2 56.9 83.1 151.4 40.4 72.0 58.3 15.6 .Calculate the percent passing each sieve, and draw a 0.45 power gradation chart with the use of a spreadsheet program. The specific steps or functions selected in the following description can vary somewhat depending on the version of the spreadsheet program being used.Calculate the fineness modulus of the sieve analysis results of Sample Problem
A sieve analysis test was performed on a sample of fine aggregate and produced the following results:Sieve, mm 4.75 2.36 2.00 1.18 0.60 0.30 0.15 0.075 panAmount retained, g 0 33.2 56.9 83.1 151.4 40.4 72.0 58.3 15.6Calculate the percent passing each sieve, and draw a 0.45 power gradation chart with the use of a spreadsheet program. The specific steps or functions selected in the following description can vary somewhat depending on the version of the spreadsheet program being used.
Chapter 5 Solutions
Materials For Civil And Construction Engineers In Si Units
Ch. 5 - Prob. 5.1QPCh. 5 - Discuss five different desirable characteristics...Ch. 5 - Discuss five different desirable characteristics...Ch. 5 - The shape and surface texture of aggregate...Ch. 5 - Define the following terms: a. Saturated...Ch. 5 - Three samples of fine aggregate have the...Ch. 5 - A sample of wet aggregate weighed 297.2 N. After...Ch. 5 - 46.5 kg (102.3 lb) of fine aggregate is mixed with...Ch. 5 - Samples of coarse aggregate from a stockpile are...Ch. 5 - Base course aggregate has a target dry density of...
Ch. 5 - Calculate the percent voids between aggregate...Ch. 5 - Calculate the percent voids between aggregate...Ch. 5 - Coarse aggregate is placed in a rigid bucket and...Ch. 5 - The following laboratory tests are performed on...Ch. 5 - Students in the materials lab performed the...Ch. 5 - The specific gravity and absorption test (ASTM...Ch. 5 - Prob. 5.18QPCh. 5 - Calculate the sieve analysis shown in Table P5.19...Ch. 5 - Calculate the sieve analysis shown in Table P5.20,...Ch. 5 - A sieve analysis test was performed on a sample of...Ch. 5 - A sieve analysis test was performed on a sample of...Ch. 5 - Draw a graph to show the cumulative percent...Ch. 5 - Referring to Table 5.6, plot the specification...Ch. 5 - Referring to the aggregate gradations A, B, and C...Ch. 5 - Table P5.26 shows the grain size distributions of...Ch. 5 - Table P5.27 shows the grain size distributions of...Ch. 5 - Three aggregates are to be mixed together in the...Ch. 5 - Table P5.29 shows the grain size distribution for...Ch. 5 - Laboratory specific gravity and absorption tests...Ch. 5 - Table P5.31 shows the grain size distribution for...Ch. 5 - Prob. 5.32QPCh. 5 - Laboratory specific gravity and absorption tests...Ch. 5 - Prob. 5.34QPCh. 5 - Define the fineness modulus of aggregate. What is...Ch. 5 - Calculate the fineness modulus of aggregate A in...Ch. 5 - Calculate the fineness modulus of aggregate B in...Ch. 5 - A portland cement concrete mix requires mixing...Ch. 5 - Discuss the effect of the amount of material...Ch. 5 - Aggregates from three sources having the...Ch. 5 - Aggregates from three sources having the...Ch. 5 - A contractor is considering using three stockpiles...Ch. 5 - Prob. 5.43QPCh. 5 - What are the typical deleterious substances in...Ch. 5 - Review ASTM D75 and summarize the following: a....
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- From the given data shown in the table below, determine the effective specific gravity of aggregates. Round off to two decimal places.arrow_forwardA box measuring 50 cm x 50 cm x 50 cm is filled to the top with dry coarse aggregate of mass 187.5 kg. The water absorption and specific gravity of the aggregate are 0.5% and 2.5, respectively. The maximum quantity of water (in kg, round off to 2 decimal places) required to fill the box completely is brisarrow_forwardA sieve analysis test was performed on a sample of aggregate and produced the results shown in Table .Calculate the percent passing through each sieve. Plot the percent passingversus sieve size on:a. a semilog gradation chart, andb. a 0.45 gradation chart (Figure A.25).What is the maximum size? What is the nominal maximum size?arrow_forward
- Calculate the bulk specific gravity of combined aggregate if you know the specific gravities of coarse aggregate (C), fine aggregate (F) and Mineral Filler (MF) are 2.61, 2.63 and 2.71 respectively. The percent for C, F, and MF can be determined based on the gradation shown belowarrow_forwardSuppose you had 10 kg (10000 g) sample of an aggregate at air dry conditions (Moisture Content = 0.07%). How much water (in grams) would be needed to bring the sample to SSD conditions? Show work.arrow_forwardTable shows the grain size distributions of aggregates A, B, and C. The three aggregates must be blended at a ratio of 15:25:60 by weight, respectively.Using a spreadsheet program, determine the grain size distribution of the blend.arrow_forward
- Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit weight. The following data are obtained: Volume of bucket =14L Weight of empty bucket = 9.21kg Weight of bucket filled with dry rodded coarse aggregate: Trial 1 =34,75 kg Trial 2 =34.06 kg Trial 3 =35.74 kg a. Calculate the average dry-rodded unit weight b.If the bulk dry specific gravity of the aggregate is 2.620, calculate the percent voids between aggregate particles for each trial.arrow_forwardCoarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit weight. The following data are obtained:Volume of bucket = 12 ft3Weight of empty bucket = 20.3 lbWeight of bucket filled with dry rodded coarse aggregate:Trial 1 = 76.6 lbTrial 2 = 75.1 lb Trial 3 = 78.8 lba. Calculate the average dry-rodded unit weightb. If the bulk dry specific gravity of the aggregate is 2.620, calculate the percent voids between aggregate particles for each trial.arrow_forwardAggregates from three sources having bulk specific gravities of 2.753, 2.649, and 2.689 were blended at a ratio of 70:20:10 by weight, respectively. What is the bulk specific gravity of the aggregate blend?arrow_forward
- Based from the proportion that you have designed, say that the concrete is mixed to fill 20 cubes (100 x 100 x 100mm) and 10 prisms (500 x 100 x 100mm), find the mass of each material based on the aggregate conditions in Table 2.arrow_forwardCoarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit weight. The following data are obtained:Volume of bucket = 1/3 ft3Weight of empty bucket = 18.5 lbWeight of bucket filled with dry rodded coarse aggregate = 55.9 lba. Calculate the dry-rodded unit weightb. If the bulk dry specific gravity of the aggregate is 2.630, calculate the percent voids in the aggregate.arrow_forwardAccording to fuller equation, to draw the maximum density line for aggregate gradation shown below , what is the percent passing corresponding 4.75 mm sieve size ?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Structural Analysis (10th Edition)Civil EngineeringISBN:9780134610672Author:Russell C. HibbelerPublisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Fundamentals of Structural AnalysisCivil EngineeringISBN:9780073398006Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel LanningPublisher:McGraw-Hill Education
Traffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage Learning
Structural Analysis (10th Edition)
Civil Engineering
ISBN:9780134610672
Author:Russell C. Hibbeler
Publisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Fundamentals of Structural Analysis
Civil Engineering
ISBN:9780073398006
Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning
Publisher:McGraw-Hill Education
Traffic and Highway Engineering
Civil Engineering
ISBN:9781305156241
Author:Garber, Nicholas J.
Publisher:Cengage Learning
Aggregates: Properties; Author: nptelhrd;https://www.youtube.com/watch?v=49yGZYeokKM;License: Standard YouTube License, CC-BY