Heating, Ventilation, and Air Conditioning: Analysis and Design
6th Edition
ISBN: 9781119628798
Author: Faye C. McQuiston; Jerald D. Parker; Jeffrey D. Spitler
Publisher: Wiley Global Education US
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 5, Problem 5.34P
Estimate the heat loss from 100 m of buried hot-water pipe. The mean water temperature is 60 C. The copper pipe with 20 mm of insulation,
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Hand written plz asap... I'll give you multiple upvote hand written plz asap...
Fast plz hand written.... I'll upvote if hand written plz asap
Pin fins are provided to increase the heat transfer from a hot surface. The perimeter of each fin is 4cm and its cross section area is 2 cm². The thermal conductivity of fin material is 200 W / mK. The fin base temperature is 230 ° C, the ambient air temperature is 30 ° C and the heat transfer coefficient is 20 W / (m²K). The fins are assumed of negligible end loss Which of the following arrangements will give higher heat transfer rate? (1) 6 fins of 10 cm length. (2) 12 fins of 5 cm length
Chapter 5 Solutions
Heating, Ventilation, and Air Conditioning: Analysis and Design
Ch. 5 - Determine the thermal conductivity of 4 in. (100...Ch. 5 - Compute the unit conductance C for 512 in. (140...Ch. 5 - Compute the unit thermal resistance and the...Ch. 5 - What is the unit thermal resistance for an inside...Ch. 5 - Compute the thermal resistance per unit length for...Ch. 5 - Assuming that the blocks are not filled, compute...Ch. 5 - The partition of Problem 5-4 has still air on one...Ch. 5 - The pipe of Problem has water flowing inside with...Ch. 5 - Compute the overall thermal resistance of a wall...Ch. 5 - Compute the overall heat-transfer coefficient for...
Ch. 5 - Estimate what fraction of the heat transfer for a...Ch. 5 - Make a table similar to Table 5-4a showing...Ch. 5 - Estimate the unit thermal resistance for a...Ch. 5 - Refer to Problem 5-13, and estimate the unit...Ch. 5 - A ceiling space is formed by a large flat roof and...Ch. 5 - A wall is 20 ft (6.1 m) wide and 8 ft (2.4 m) high...Ch. 5 - Estimate the heat-transfer rate per square foot...Ch. 5 - A wall exactly like the one described in Table...Ch. 5 - Prob. 5.19PCh. 5 - Compute the overall heat-transfer coefficient for...Ch. 5 - Compute the overall heat transfer for a single...Ch. 5 - Determine the overall heattransfer coefficient for...Ch. 5 - A basement is 2020ft(66m) and 7 ft (2.13 m) below...Ch. 5 - Estimate the overall heat-transfer coefficient for...Ch. 5 - Rework Problem 5-23 assuming that the walls are...Ch. 5 - A heated building is built on a concrete slab with...Ch. 5 - A basement wall extends 6 ft (1.8 m) below grade...Ch. 5 - A 2440ft(7.312.2m) building has a full basement...Ch. 5 - The floor of the basement described in Problem...Ch. 5 - Assume that the ground temperature tg is 40 F (10...Ch. 5 - Use the temperatures given in Problem 5-30 and...Ch. 5 - A small office building is constructed with a...Ch. 5 - A 100 ft length of buried, uninsulated steel pipe...Ch. 5 - Estimate the heat loss from 100 m of buried...Ch. 5 - A large beverage cooler resembles a small building...Ch. 5 - Consider the wall section shown in Fig. 5-10. (a)...Ch. 5 - A building has floor plan dimensions of 3060ft....Ch. 5 - Compute the temperature of the metal roof deck of...Ch. 5 - Consider the wall section shown in Fig. -4a,...Ch. 5 - Consider the knee space shown in Fig. 5-11. The...Ch. 5 - Estimate the temperature in an unheated basement...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
What is the importance of modeling in engineering? How are the mathematical models for engineering processes pr...
Heat and Mass Transfer: Fundamentals and Applications
6–1C A mechanic claims to have developed a car engine that runs on water instead of gasoline. What is your resp...
Thermodynamics: An Engineering Approach
Locate the centroid of the area. Prob. 9-17
Engineering Mechanics: Statics
23.23 A highly oxidized and uneven round bar is being turned on a lathe. Would you recommend a small or a large...
Manufacturing Engineering & Technology
5.1 through 5.9
Locate the centroid of the plane area shown.
Fig. P5.1
Vector Mechanics for Engineers: Statics and Dynamics
What types of polymers are most commonly blow molded?
Degarmo's Materials And Processes In Manufacturing
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- In a thermal power plant, a horizontal copper pipe of "D" diameter, "L" length and thickness 1.2 cm enters into the boiler that has the thermal conductivity as 0.37 W/mK. The boiler is maintained at 113C and temperature of the water that flows inside the pipe is at 29C. If the energy transfer (Q) is 118779 kJ in 7 hours. Calculate: 4-Length of the pipe, if D = 0.017 L. 5-Pipe Diameter (in mm)arrow_forwardIf hand written i'll upvote otherwise downvote?...arrow_forwardA steam pipe carrying steam at 380 kPa pressure for a distance of 120 m in a chemical plant is not insulated. Estimate the Amount of heat saved if 16 cm steam line were covered with 85% magnesia pipe covering 5 cm thick. Take room temperature to be 36 ℃. Thermal conductivity of 85% magnesia is 0.0745 W/m−K , unit convective coefficient of room air, ho = 12 W m2−K .Take the steam temperature as 142℃. Use atleast 4 decimal places in every computationarrow_forward
- Fluid is flowing through a 20 mm inside diameter and 25 mm outside diameter brass tube at no leaking with temperature at 65℃ and length of 10 m. Surface conduction of hot fluid is 5.2W/(m^2℃) and thermal conductivity of brass is 12.84W/(m℃). Brass tube is covered by silica of 6 mm thickness with thermal conductivity of 13.84W/(m℃) . Outside of it, is a fluid with 45℃ with surface conductance of 3.2W/(m^2℃). Find the heat transfer from the hot fluid with temperature of 65℃ to fluid with temperature of 45℃.arrow_forwardSteel pipe (outer diameter 100 mm) is covered with two layers of insulation. The inner layer, 40 mm thick, has a thermal conductivity of 0.07 W / (m K). The outer layer, 20 mm thick, has a thermal conductivity of 0.15 W / (m K). Pipes are used to deliver steam with a pressure of 700 kPa. The temperature on the outer insulation surface is 24 ° C. If the pipe is 12 m long, determine the following: (assuming that the conduction heat transfer resistance of the steel pipe and the vapor convection resistance are negligible). a. Heat loss per hour. = Answer kJ / hour. b. Temperature between insulation layers. = Answer ° C.arrow_forwardSteel pipe (outer diameter 100 mm) is covered with two layers of insulation. The inner layer, 40 mm thick, has a thermal conductivity of 0.07 W / (m K). The outer layer, 20 mm thick, has a thermal conductivity of 0.15 W / (m K). Pipes are used to deliver steam with a pressure of 600 kPa. The temperature on the outer insulation surface is 24 ° C. If the pipe is 8 m long, determine the following: (assuming that the conduction heat transfer resistance of the steel pipe and the vapor convection resistance are negligible). a. Heat loss per hour. = kJ / hour. b. Temperature between insulation layers. = ° Carrow_forward
- A sphere which is 12.7 mm in diameter, is at 66 °C before it is inserted into an airstream having a temperature of 27 °C. The surface temperature of the sphere is 55 °C after 69 seconds measured by a thermocouple. This sphere has density 8933 kg/m³, cp = 389 J/kg∙K, k=398 W/m K Assume this sphere can be treated as a lumped system. Find the convective heat transfer coefficient and then calculate Bi number to justify the assumption that this sphere can be treated as a lumped system.arrow_forwardSteel pipe (outer diameter 100 mm) is covered with two layers of insulation. The inner layer, 40 mm thick, has a thermal conductivity of 0.07 W / (m K). The outer layer, 20 mm thick, has a thermal conductivity of 0.15 W / (m K). Pipes are used to deliver steam with a pressure of 800 kPa. The temperature on the outer insulation surface is 24 ° C. If the pipe is 10 m long, determine the following: (assuming that the conduction heat transfer resistance of the steel pipe and the vapor convection resistance are negligible). a. Heat loss per hour. = AnswerkJ / hr. b. Temperature between insulation layers. = Answer ° C.arrow_forward4arrow_forward
- 1. Saturated steam at 500 K flows in a 0.20 m inside diameter, 0.21 m outside diameter pipe. The pipe is covered with 0.08 m of insulation with a thermal conductivity of 0.10 W/m-K. The pipe's conductivity is 52 W/m-K. The ambient temperature is 300 K. The unit convective coefficients are h; = 18,000 W/m²-K and ho = 12 W/m²-K. Determine the heat loss (kJ/min) from 4 m of pipe. • show conversions, units, and box in your final answersarrow_forwardYou are designing a 3m x 3m floor with radiant heating. The floor has 12 parallel pex pipes (k = 40 W/mK) of L = 3m, OD = 25mm and ID = 20mm. Hot water (TInfintiy 1 = 90oC, h = 200 W/m2K) runs through the pipes continuously. The surface below the pipes is perfectly insulated. Above the pipes, there is a 3mm layer of bonding material (? = 12 W/mK) and a 9mm layer of tile (k = 2 W/mK). Above the tile, there is air (TInfinity 2 = 25oC, h = 20 W/m2K). Properties of Air: k = 0.025 W/mK, Pr = 0.72, v = 1.847 x 10−5, u = 16.84 x 10−6, p = 1.2 kg/m3, B = 1/Tf (ideal gas), Hint: Assume that the “layer” of pipe starts at the center point (e.g. for conduction purposes, the pipe is OD divided by 2 thick). For convection, consider the entire pipe surface. a) What is the total heat rate entering the room above the floor? b) What is the temperature of the top of the tile?arrow_forwardSteel pipe (outer diameter 100 mm) is covered with two layers of insulation. The inner layer, 40 mm thick, has a thermal conductivity of 0.07 W / (m K). The outer layer, 20 mm thick, has a thermal conductivity of 0.15 W / (m K). Pipes are used to delivering steam with a pressure of 600 kPa. The temperature on the outer insulation surface is 24 ° C. If the pipe is 10 m long, determine the following: (assuming that the conduction heat transfer resistance of the steel pipe and the vapor convection resistance are negligible). a. Hourly heat loss ... (kj / hr)b. temperature between insulation layers ... (° C.)arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Understanding Conduction and the Heat Equation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=6jQsLAqrZGQ;License: Standard youtube license